start stop button SUBARU IMPREZA 2002 2.G Owners Manual

Keys and doors
2-11
– CONTINUED –
4. Place the ignition key into the ignition switch and
cycle the switch from LOCK to ON ten times within
15 seconds . Be sure to stop at the LOCK position.
The horn will sound once to indicate that you are in
the transmitter programming mode. NOTE
You must finish the next step (opening the driv-
er’ s door) within 45 seconds of starting this pro-
cedures.
To program the transmitters:
HB1005BB
1. Open the driver ’s door.
2. Close the driver ’s door.
HB1000DC
1) Press any button.
3. Press and release any button on the transmitter
that you wish to program into the system. The horn will sound two times to indicate that the transmitter
has been programmed.
Any additional transmitters can also be programmed
at this time. Repeat steps 1 through 3 for an addi-
tional transmitter.
To exit the programming mode:
1. After all of your transmitters are programmed, re-
move the key from the ignition switch.
The horn will sound three times to indicate that the
system has exited the programming mode.
2. Make sure that the keyless entry system properly

Audio
5-9
– CONTINUED –
To play back a compact disc
n When CD is not in the player
Hold a disc with a finger in the center hole while
gripping the edge of the disc, then insert it in to the
slot (with the label side up) and the player will auto-
matically pull the disc into position.A single CD (8 cm/3 inch CD) may also be used
without any adapter.
NOTE Make sure to always insert a disc with the label
side up. If a disc is inserted with the label side down, it might be ejected or the player mightshut off. After the last song finishes, the player will
automatically return to track 1 (the first song onthe disc).
n When CD is in the player
Press the “DISC” button (9). The display will show
“CD” and the player will start playback.
NOTE
After the last song finishes, playback will auto-
matically return to track 1 (the first song on the disc).
To select a song from its beginning
n Forward direction
Briefly press the “
” button (11) to skip to the begin-
ning of the next track. Each time the button is
pressed, the indicated track number will increase.
n Backward direction
Briefly press the “ ” button (11) to skip to the begin-
ning of the current track. Each time the button is
pressed, the indicated truck number will decrease.
Fast forwarding and fast reverse
n Fast forwarding
Press the “
” button (11) continuously for more than
1 second to fast forward the disc.
Release the button to stop fast forwarding.
n Fast reverse
Press the “ ” button (11) continuously for more than
1 second to fast reverse the disc.
Release the button to stop fast reverse.
Repeat playback
Press the “RPT/RDM” button (10) and release it in
less than 2 seconds while a song is playing to play
the song repeatedly. The “RPT” indicator will come
on and the song will be played continuously. To can-

Audio
5-12
To start playback
When the “CD” button (13) is pressed, the CD
changer will start playback. The display shows the
current disc number, track number and the elapsed
time during playback. NOTE If a disc is in the player, the “DISC” button is
used to change from CD player operation to DISC changer operation. Each time the “DISC”
button is pressed, the operating mode will
change alternately. At the end of the disc, the player automatically
continues with the next disc. After playback on the last disc finishes, play-
back will automatically return to the first disc. If you have loaded fewer than 6 discs, any mis-
sing disc is automatically skipped.
Selection of a desired disc
You can select a desired disc from among the discs
contained in the magazines only by pressing the
corresponding number one of the disc select but-
tons. If you are to listen to the 7th disc in the double
magazine (12 discs), for example, it is selected firstby selecting “M2” (“M2” means 2nd magazine) with
the “DISC” button and then pressing the “1” button
of the disc select buttons. All other discs in the mag- azines can also be selected in a similar way.
NOTE No disc change takes place if the button corre-
sponding to the magazine slot in which no disc is loaded is pressed. If the direct disc button corresponding to the
disc now in playback is pressed again, the disc will be replayed from its beginning.
To select a song from its beginning
n Forward direction
Briefly press the “
” button (12) to skip to the begin-
ning of the next track. Each time the button is
pressed, the indicated track number will increase.
n Backward direction
Briefly press the “ ” button (12) to skip to the begin-
ning of the current track. Each time the button is
pressed, the indicated track number will decrease.
Fast forwarding and fast reverse
n Fast forwarding
Press the “
” button (12) continuously for more than
1 second to fast forward the disc.
Release the button to stop fast forwarding.
If you continue fast forwarding to the end of the disc,

Audio
5-13
– CONTINUED –
the CD changer will automatically stop fast forward-
ing and start playback beginning with the first track
on the current disc.
n Fast reverse
Press the “ ” button (12) continuously for more than
1 second to fast reverse the disc.
Release the button to stop fast reverse.
If you continue fast reverse to the beginning of the disc, the CD changer will automatically stop fast
reverse and start playback beginning with the first
track on the current disc.
Repeat playback
Use this to play a certain track repeatedly. During
playback, press the “RPT/RDM” button (14) and re-
lease it in less than 2 seconds. The “RPT” indicator
will come on and the song will be played continu-
ously. To cancel the repeat mode, press the buttonagain. Then the “RPT” indicator goes out, and nor-
mal playback mode is restored.
Random playback
Use this to play the tracks on the disc in random or-
der. During playback, press the “RPT/RDM” button
(14) and hold it in for more than 2 seconds. The
“RDM” indicator will come on and all songs on the
disc will be played in a random order. To cancel the random mode, press the button again.
Then the
“RDM” indicator goes out, and normal
playback mode is restored.

Audio
5-20
NOTE Only use good quality cassettes (cassettes
longer than C-90 are not recommended). Put cassettes back in their boxes immediately
after use to protect them from dust and dirt andto prevent the tape from unwinding. Never expose cassettes to heat, direct sunlight
or moisture. Clean the tape head (once or twice a month)
using a
wet-type cleaning cassette.
To play back a cassette tape
n When cassette tape is not in the player
When a cassette is partially inserted, it is automati-
cally drawn in and starts tape playback.
n When cassette tape is in the player
When the “TAPE” button (12) is pressed, the display
will show “PLAY” and the player will start playback.
Tape travel indicators
These indicate the direction the cassette tape ismoving. : indicates that the top side of the cassette is be-
ing played back. : indicates that the bottom side of the cassette is
being played back.
Program switching button (PROG)
When the program switching button “PROG” (16) is
pressed during playback, the tape travel indicatorswill switch and the player will begin playing back theopposite side of the tape. The same mechanism is
automatically activated when the end of the tape is
reached. This allows the opposite side of the tape to
play, providing continuous playback.
Fast-forward button (FF)
To fast-forward the tape, press the “FF” button (15).
The display will show “FF”. To stop fast-forwarding,
press the “FF” or “TAPE” (12) button.
Rewind button (REW)
To rewind the tape, press the “REW” button (17).
The display will indicate “REW”. To stop rewinding,
press the “REW” or “TAPE” (12) button.
Eject button (
)
When “
” button (10) is pressed, play back stops
and the cassette tape is ejected. The ejection function also operates when the ignition switch is in the “LOCK” position. Always make cer-
tain that you remove the cassette tape.

Audio
5-24
press any of the other mode buttons “FM” (2), “AM”
(1) and “TAPE” (12), the player will enter standby
mode. Press the “CD” button to start playback.
n Loading all the magazine (Full disc loading mode)
1. If you continue to press the “LOAD” button for
more than 1.5 seconds, the player will produce beep sound and will enter the full disc loading mode.
2. A “DISC” indicator will blink, and the “IN” will be
on display for a period of 15 seconds. If a disc issuccessfully loaded during this period, the “DISC”
indicator will stop blinking and will steadily light.
3. When the loading of a disc is complete, the next
“DISC” indicator will blink. Then repeat Step 2.
4. When the magazine is filled with discs by repeat-
ing Steps 2 and 3, the player will start playback of
the discs, beginning with the one inserted first.
If you fail to insert any disc during each 15-second interval, the full disc loading mode will be canceled,
and the player will start playback of the disc in-
serted first.
How to play back a CD or make a pause
n When there is no CD inserted:
Insert a CD by referring to “How to Insert a CD(s) ”.When a CD is loaded, the player will start playback
of the CD, beginning with the first number.
n When there are CDs loaded:
Press a desired one of the “DISC SELECT ” buttons
(26) the “DISC” indicator of which steadily lights up.
The player will then start playback of the selected
CD, beginning with the first number.
Selecting a desired track (TRACK)
HS5005BA
❚: Skipping forward
❚ : Skipping backward
: Fast forwarding
: Fast reversing

Starting and operating
7-25
– CONTINUED –
Parking your vehicle
WARNING
Never leave unattended children or pets in
the vehicle. They could accidentally injure
themselves or others through inadvertent op-
eration of the vehicle. Also, on hot or sunny
days, the temperature in a closed vehiclecould quickly become high enough to cause
severe or possibly fatal injuries to people. Do not park the vehicle over flammable ma-
terials such as dry grass, waste paper or rags,as they may burn easily if they come near hotengine or exhaust system parts. Be sure to stop the engine if you take a nap
in the vehicle. If engine exhaust gas enters the
passenger compartment, occupants in the ve-hicle could die from carbon monoxide (CO)contained in the exhaust gas.
CAUTION
Never drive while the parking brake is set be-
cause this will cause unnecessary wear on the brake linings. Before starting to drive, always
make sure that the parking brake has been ful-ly released.
To set the parking brake, press the brake pedal firm-ly and hold it down while fully pulling up the parking
brake lever.
HB4001BA
To release the parking brake, pull the lever up slight-
ly, press the release button, then lower the lever
while keeping the button pressed.
When the parking brake is set while the engine is