buttons SUBARU IMPREZA 2003 2.G User Guide

Audio
5-31
– CONTINUED –
In-dash 6 CD auto changer 1 (if equipped) Loading and unloading compact discs
(1) Disc slot
(2) Disc indicators (disc No.1 to 6)
(3) Disc select buttons (disc No.1
to 6)
(4) Eject button
(5) Disc slot indicator

Audio
5-32
CAUTION
Do not attempt to insert two or more discs
into the slot at a time. Doing so can cause me-
chanical damage to the CD changer. Use only music CDs identified by a
mark. Do not use CDs listed below which could
cause damage to the CD player.
3-inch (8 cm) compact disc.
Any disc with a peel-off or seal on it.
Any disc with scratches and/or dust.
Bent disc.
Cleaning disc.
CD accessory. (E.g., 3-inch (8 cm) disc
adapter)
Do not insert or remove any disc when the
automatic transmission selector lever is in thepark position; the selector lever in that posi-tion can interfere with disc insertion or remov-al, causing scratches on the disc surface (for
AT vehicles).
To insert a disc
1. Press one of the “Disc select ” buttons (3) (num-
bered from 1 to 6) for which the disc indicator light(2) is “OFF”. The Disc indicator lights are located directly above
the corresponding
“Disc select ” buttons.
2. The indicator will begin blinking. The blinking willlast for 15 seconds.
During this period, insert a desired disc, and the
disc will begin to play. (If any disc is not inserted during this period, the “Disc slot ” (1) door will close.
Repeat step 1.)
Be sure to hold a disc with the label side (the side
where titles are printed) up.
3. To insert another disc, repeat step 1 and 2
choosing a different disc select button.
To insert six discs at a time
1. Press and hold the “Disc select ” button number 1
until all disc indicators begin blinking (about 1.5 se-conds).
2. The indicators will blink for 15 seconds. During
this period, insert desired six discs.
3. When all discs are loaded, the first disc will begin
to play. (If no disc is inserted within this 15 seconds,
the entire disc load sequence will be canceled.)
To remove a disc
1. Press the desired one of the “Disc select ” buttons
(3) (numbered from 1 to 6) for which the disc indica-tor light is on.
2. Press the “Eject button ” (4). The selected disc

Audio
5-33
– CONTINUED –
will be ejected and the indicator light will begin blinking.
3. To remove another disc, repeat step 1 and 2
choosing a different “Disc select ” button.
(To remove discs when the ignition switch is in the
“Lock” position, press the “Eject” button, and the
first disc will be ejected. Press the “Eject” button
again, and the next disc will be ejected and so on.At this time, the “Disc select ” buttons are disabled.)
To remove all discs at one time
1. Press and hold the “Eject” button (4) until all
“Disc” indicators begin blinking (about 1.5 se-
conds), and the first disc will be ejected.
2. When the disc is removed, the next one will be
ejected, and so on.
To replace a playing disc with another
Simply press the desired one of “Disc select ” but-
tons (3) (numbered from 1 to 6) or press the “DISC
select” button on the radio unit to select the desired
disc, and the disc will begin to play.
Disc indicators
Lit: when the corresponding storage tray is occu-pied by a disc.
Blinking: Disc player is either in loading, eject or
changing mode. OFF: No disc is loaded or the ignition switch is in the
“LOCK”
position.
n Open/Closed disc slot indicator
When the disc slot is open, the disc indicators onboth sides of the slot illuminate.
Function control
Refer to CD changer control operating instructions described in the “Type B audio set ” section.