low beam SUBARU IMPREZA 2005 2.G Owners Manual

19
–
CONTINUED –
„Light control and wiper control levers/switches
12
3
4
5
1
10 9 7
11
2
6
8
UGF064BB
1) Parking light switch (page 3-35)
2) Windshield wiper (page 3-38)
3) Mist (page 3-39)
4) Windshield washer (page 3-39)
5) Rear window wiper and washer
switch (page 3-40)
6) Wiper control lever (page 3-38)
7) Illumination brightness control (page 3-33)
8) Light control lever (page 3-30)
9) Headlight ON/OFF (page 3-30)
10) Headlight flasher High/Low beam change (page 3-30)
11) Turn signal (for lane change) (page 3-32)
12) Turn signal (page 3-32)

3-2
Instruments and controls
High/low beam change (dimmer) .................... 3-31
Headlight flasher .............................................. 3-31
Daytime running light system (except U.S.-spec. WRX-STi) ......................... 3-32
Turn signal lever ........................................... 3-32
Illumination brightness control ................... 3-33
Illumination brightness control (WRX-STi) .................................................. 3-34
Headlight beam leveler (U.S.-spec. WRX-STi) ................................ 3-34
Parking light switch ..................................... 3-35
Fog light button (if equipped) ..................... 3-36
Wiper and washer ......................................... 3-36 Windshield wiper and washer switches ......... 3-38
Rear window wiper and washer switch – Wagon .......................................................... 3-40
Rear window defogger button ..................... 3-41
Windshield wiper deicer (if equipped) ........ 3-43
Intercooler water spray switch (WRX-STi) .................................................. 3-44
Mirrors ........................................................... 3-45 Inside mirror ...................................................... 3-45
Outside mirrors ................................................. 3-48
Tilt steering wheel ........................................ 3-50
Horn ............................................................... 3-51

3-31
Instruments and controls
– CONTINUED –
„High/low beam change (dimmer)
To change from low beam to high beam, push the turn
signal lever forward. When the headlights are on high
beam, the high beam indicator light “ ” on the in-
strument panel is also on.
To switch back to low beam, pull the lever back to the
detent position. „
Headlight flasher
To flash the headlights, pull the lever toward you and
then release it. The high beam will stay on for as long
as you hold the lever. The headlight flasher works
even though the lighting switch is in the “OFF” posi-
tion.
When the headlights are on high beam, the high beam
indicator light “ ” on the instrument panel alsocomes on.
Do not hold the lever in the flashing position for
HS3026CAHS3026DA

3-32
Instruments and controls
more than just a few seconds.
„ Daytime running light system (except
U.S.-spec. WRX-STi)
The low beam headlights will automatically come on at
reduced brightness when the engine has started, un-
der the following conditions: y The parking brake is fully released.
y The light switch is in the “OFF” or “ ” position.
y The automatic transmission selector lever is set at
other than the “P” position.
The tail lights, parking lights, and side marker
lights are not turned on by the daytime running
light system. The light switch must always be
turned to the “ ” position when it is dark
outside.
Turn signal lever
1) Right turn
2) Left turn
3) Lane change for right
4) Lane change for left
To activate the right turn signal, push the turn signal le-
ver up. To activate the left turn signal, push the turn
signal lever down. When the turn is finished, the lever
will return automatically. If the lever does not return af-
ter cornering, return the lever to the neutral position by
hand.
To signal a lane change, push the turn signal lever up
1 2 3
4
HS3027BB

3-34
Instruments and controls
Illumination brightness control
(WRX-STi)
The brightness of the combination meter can be ad-
justed in five steps with the headlight switch either the
OFF position or the “ ” or “ ” position.
When the control dial is turned upward or downward,
the instrument panel’s illumination brightness is indi-
cated by the trip meter. The brightness is shown in five
steps from “ ” (dimmest) to “ ” (brightest).
If the control dial is not turned for three seconds, the
trip meter returns to its original trip meter indication.
Headlight beam leveler (U.S.-spec. WRX-STi)
The WRX-STi version has High-Intensity Discharge
(HID) headlights on the low beam setting. The HID
headlights generate more light than conventional halo-
gen headlights. Therefore a driver of an oncoming ve-
hicle may experience too much glare when your head-
light beam height adjustment is high due to the vehicle
carrying heavy load.
The headlight beam leveler can be used to adjust
beam height to avoid such a condition.
The higher the number the knob is turned to, the lower
UG3032AAUG3511AA

3-35
Instruments and controls
– CONTINUED –
the beam becomes.Parking light switch
The parking light switch operates regardless of the ig-
nition switch position.
By pushing the front end of this switch, following lights
will come on.
– Parking lights
– Tail lights
– License plate lights
To turn off, push the rear end of the parking light switch.
Avoid leaving these lights on for a long time because
that will run down the battery.
P
UG3043BA

3-36
Instruments and controls
Fog light button (if equipped)
The fog lights operate only when the headlights are on
low beam. Push the fog light button to turn the fog
lights on.
Press the button again to turn them off.
The indicator light located on the button will illuminate
when the fog lights are on.Wiper and washer
In freezing weather, do not use the windshield
washer until the windshield is sufficiently
warmed by the defroster.
Otherwise the washer fluid can freeze on the
windshield, blocking your view.
y
Do not operate the washer continuously for
more than ten seconds, or when the washer flu-
id tank is empty. This may cause overheating of
the washer motor. Check the washer fluid level
frequently, such as at fuel stops. y Do not operate the wipers when the wind-
shield or rear window is dry. This may scratch
the glass, damage the wiper blades and cause
the wiper motor to burn out. Before operating
the wiper on a dry windshield or rear window,
always use the windshield washer.y In freezing weather, be sure that the wiper
blades are not frozen to the windshield or rear
window before switching on the wipers. At-UG3512BA

11 - 7 0
Maintenance and service
„
Headlights (U.S.-spec. WRX-STi)
High-intensity-discharge (HID) bulbs are used
for the low beams of the headlights on the U.S.-
spec. WRX-STi. These HID bulbs use an ex-
tremely high voltage. To avoid the risk of an
electric shock and resulting serious injury, you
should not attempt to replace them. Neither
should you attempt to replace the high-beam
bulbs, remove/refit the headlight assemblies,
or remove any headlight-assembly compo-
nents. For replacement of the headlight bulbs
(low-beam and high-beam), removal and instal-
lation of the headlight assemblies, and removal
of headlight-assembly components, contact
your SUBARU dealer.
Wattage Bulb No.
1) Front turn signal 12V-21W –
2) Spot light 12V-8W –
3) Room light 12V-8W –
4) Parking light 12V-5W 168
5) Low beam head light U.S.-spec. WRX-STi 12V-35W D2R Except U.S.-spec. WRX-STi 12V-55W H1
6) Front fog light 12V-55W H3
7) High beam head light 12V-60W 9005 (HB3)
8) Trunk room light 12V-16W W16W
9) High mount stop light Sedan
(in compartment) 12V-18W 921
(in rear spoiler) 12V-1.2W –
Wagon 12V-13W 912
10) Backup light 12V-21W 7440
11) Rear turn signal 12V-21W (Amber)–
12) Brake/tail light 12V-21/5W 7443
13) Tail light 12V-21/5W 7443
14) Brake light 12V-21W 7440
15) License plate light 12V-5W 168 16) Cargo area light 12V-13W –
Wattage Bulb No.

11 -7 1
Maintenance and service
– CONTINUED –
„Headlights (Except U.S.-spec. WRX-
STi)
Halogen headlight bulbs become very hot while
in use. If you touch the bulb surface with bare
hands or greasy gloves, finger prints or grease
on the bulb surface will develop into hot spots
and cause the bulb to break. If there are finger
prints or grease on the bulb surface, wipe them
away with a soft cloth moistened with alcohol.
NOTE yIf headlight aiming is required, consult your
SUBARU dealer for proper adjustment of the head-
light aim. y It may be difficult to replace the bulbs. Have
your SUBARU dealer replace the bulbs if neces-
sary. T
Low beam light bulbs
1. Remove the bulb cover, by turning it counterclock- wise.
UGB516BA

12-10
Specifications
Bulb chart
Description Wattage Bulb type
Headlight
U.S.-spec. WRX-
STi versionLow beam 12V-35W D2R
High beam 12V-60W 9005 (HB3)
Except U.S.-spec.
WRX-STi version Low beam 12V-55W H1
High beam 12V-60W 9005 (HB3)
Front fog light 12V-55W H3
Front turn signal 12V-21W –
Parking light 12V-5W 168
Rear combination
light Brake light (Sedan) 12V-21W 7440
Brake/tail light 12V-21/5W 7443
Turn signal light 12V-21W (Amber) –
Tail light (Sedan) 12V-21/5W 7443
Back-up light 12V-21W 7440 High mount stop light
Sedan
(in compartment) 12V-18W 921
Sedan
(in rear spoiler) 12V-1.2W –
Wagon 12V-13W 912
License plate light 12V-5W 168
Trunk room light 12V-16W W16W
Cargo area light 12V-13W –
Front ashtray light 12V-1.4W –
Dome light 12V-8W –
Map light 12V-8W –
Description Wattage Bulb type