sensor SUBARU IMPREZA WRX 2002 2.G User Guide

Instruments and controls
3-26
Compass mirror (if equipped)
HB6019BC
1) Left button
2) Auto dimming indicator
3) Photosensor
4) Right button
The inside electronic compass mirror has an anti-
glare feature which automatically reduces glare
coming from headlights of vehicles behind you. It also contains a built-in compass. By pressing and releasing the left button, the au-
tomatic dimming function is toggled on or off. Whenthe automatic dimming function is on, the auto dim-
ming indicator light (green) located to the right of the button will illuminate.
By pressing and releasing the right button, the
compass display is toggled on or off. When the
compass is on, an illuminated compass reading will
appear in the lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror
surface turns bright if the transmission is shifted into
reverse. This is to ensure good rearward visibility
during reversing.
n Photosensors
HB6020BA
The mirror has a photosensor attached on both the
front and back sides. If the glare from the headlights
of vehicles behind you strikes the mirror, these sen-
sors detect it and make the reflection surface of the
mirror dimmer to help prevent you from being

Instruments and controls
3-27
– CONTINUED –
blinded. For this reason, use care not to cover the
sensors with stickers, or other similar items. Periodi-
cally wipe the sensors clean using a piece of dry
soft cotton cloth or an applicator.
n Compass calibration
1. For optimum calibration, switch off all nonessen-
tial electrical accessories (rear window defogger,
heater/air conditioning system, spotlight, etc.) and
ensure all doors are shut.
2. Drive to an open, level area away from large me-
tallic objects or structures and make certain the igni-
tion switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then
release, and the compass will enter the calibration
mode. “CAL” and direction will be displayed.
4. Drive slowly in a circle until “CAL” disappears
from the display (about two or three circles).
5. The compass is now calibrated. Further calibra-
tion is not required. The compass will automatically
calibrate from this point forward. n
Compass zone adjustment
HB6021AA
Compass calibration zones
1. The zone setting is factory preset to Zone 8. Re- fer to the “Compass calibration zone ” map shown
above or one attached to the end of this manual to
verify that the compass zone setting is correct for your geographical location.
2. Press and hold the right button for 3 seconds
then release, and the word “ZONE” will briefly ap-
pear and then the zone number will be displayed.
3. Press the right hand button repeatedly to cycle
the display through all possible zone settings. Stop
cycling when the correct zone setting for your loca-
tion is displayed.

Audio
5-21
– CONTINUED –
Tape program sensor button (TPS)
n Blank skip
When the “TPS” button (13) is pressed, the “TPS” in-
dicator will come on and the player will automatically
skip any blank portion of 15 second or more and
play the next program, even if it is on the other side.
To cancel blank skip mode, press the “TPS” button
again.
n Blank search
Press “TPS” button (13) during playback to return to
the beginning of the current selection or to skip to
the beginning of the next selection. To use this func-
tion, press the “TPS” button to turn on the “TPS” in-
dicator. If the fast-forward button “FF” (15) is then
pressed, the player advances the tape to the begin-
ning of the next selection and starts playing it. If the
rewind button “REW” (17) is pressed instead, the
player rewinds the tape to the beginning of the cur-
rent selection and starts replaying it. The “TPS”
function may not operate properly under the follow- ing conditions: When the recording level is low.
When there are long pauses in the middle of a
selection. When the tape contains verbal material such as
conversations.
When the blanks between selections are shorter
than five seconds. When there are no blanks between selections (live
concerts, etc.).
Repeat button (RPT)
Push the “RPT” button (11) to repeat the piece of
music being listened to. To use this function, push the “RPT” button while the piece you want to hear
again is being played. “RPT” will be indicated on the
display. When the selection ends, the cassette play-
er automatically rewinds to the beginning of the
piece and the selection begins again. To cancel the
repeat function, push the “RPT” button again. Until
the repeat function is cancelled, the same piece of
music will be repeated indefinitely. The “RPT” func-
tion may not operate properly under the followingconditions: When the recording level is low.
When there are long pauses in the middle of a
selection. When the tape contains verbal material such as
conversations. When the blanks between selections are shorter
than five seconds. When there are no blanks between selections (live
concerts, etc).

Audio
5-22
Dolby B NR button ()
Press “
” button (14) when playing tapes re-
corded using the Dolby NR system*. The “” in-
dicator will light up and high-frequency noise on the
tape will be reduced for clearer sound reproduction.
* Noise reduction system manufactured under license from Dolby Laboratories Licensing Corporation.
“Dolby” and the
double-D Symbol are trade marks of Dolby Laboratories Li-
censing Corporation.
n Auto metal sensor
The cassette player automatically adjusts for metal or CrO 2 tape.
Built in CD changer operation
HS5004DB
(18) LOAD button
(19) SCAN button
(20) Disc slot
(21) CD button
(22) Eject button
(23) Random button
(24) Fast forward/Fast reverse and
track UP/DOWN knob
(25) Repeat button
(26) Disc select button