catalytic converter SUBARU LEGACY 1996 Service Repair Manual

ON-BOARD
DIAGNOSTICS
II
SYSTEM
[Tiq2]
2-

1
.
General

1~
Engine
control
module
(ECM)
~
Radiator
fan

~2
Ignition
coil~s
Radiator
fan
relay

~3
Ignitqr
~s
Pressure
sources
switching
solenoid
valve

~4
Crankshaft
position
sensor
~
Knock
sensor

~5
Camshaft
position
sensor
~
Back-pressure
transducer

Throttle
position
sensor
~s
Front
oxygen
sensor

~7
duel
injectors
~o
Rear
oxygen
sensor
(Except
California
model)

~8
Pressure
regulator
~
Pressure
sensor

Engine
coolant
temperature
sensor
~z
A/C
compressor

~o
Mass
air
flow
sensor
~
Inhibitor
switch

Idle
air
control
solenoid
valve
~
CHECK
ENGINE
malfunction
indicator
lamp
(MIL)

~z
Purge
control
solenoid
valve
~
Tachometer

0
Fuel
pump
~s
A/C
relay

0
PCV
valve
~
A/C
control
module

~s
Air
cleaner
~eIgnition
switch

Canister
~
Transmission
control
module
(TCM)

~
Main
relay
~o
Vehicle
speed
sensor
2

~a
Fuel
pump
relay
~
Data
link
connector
(For
Subaru
select
monitor)

~s
Fuel
filter
@
Data
link
connector
(For
Subaru
select
monitor
and

~o
Front
catalytic
converter
OBD-II
general
scan
tool)

Rear
catalytic
converter
@
Two
way
valve

~2
MGR
valve
~a
Rear
oxygen
sensor
(California
model
only)

EGR
control
solenoid
valve
~
Filter

3

2-7
[72A2]
ON-BOARD
DIAGNOSTICS
Ii
SYSTEM

2
.
Electrical
Components
Location

6

%
Front
oxygen
sensor
~
Front
catalytic
converter

~9
Rear
oxygen
sensor
(Except
California
model)
~2
Rear
catalytic
converter

Rear
oxygen
sensor
(California
model)

B2M0724
1. Front Catalytic Converter
A: REMOVAL
1) Disconnect front oxygen sensor connector.
B2M0725
2) Disconnect rear oxygen sensor connector. (California
2200 cc model)
B2M0312
3) Lift-up the vehicle.
4) Disconnect rear oxygen sensor connector. (Except Cali-
fornia 2200 cc model)
B2M0055
5) Separate center exhaust pipe from rear exhaust pipe.
B2M0054
6) Remove bolts which hold front exhaust pipe onto cylin-
der heads.
2
2-1SERVICE PROCEDURE
1. Front Catalytic Converter

B2M0313
7) Remove front exhaust pipe and center exhaust pipe
from hanger bracket.
CAUTION:
Be careful not to pull down front exhaust pipe and
center exhaust pipe.
B2M0060
8) Separate front catalytic converter from front exhaust
pipe and center exhaust pipe.
B2M0060
B: INSTALLATION
CAUTION:
Replace gaskets with new ones.
1) Install front catalytic converter to front exhaust pipe and
center exhaust pipe.
Tightening torque:
30±5 N⋅m (3.1±0.5 kg-m, 22.4±3.6 ft-lb)
B2M0313
2) Install front exhaust pipe and center exhaust pipe.
And temporarily tighten bolt which installs center exhaust
pipe to hanger bracket.
B2M0054
3) Tighten bolts which hold front exhaust pipe onto cylin-
der heads.
Tightening torque:
30±5 N⋅m (3.1±0.5 kg-m, 22.4±3.6 ft-lb)
3
2-1SERVICE PROCEDURE
1. Front Catalytic Converter

B2M0055
4) Install center exhaust pipe to rear exhaust pipe.
Tightening torque:
18±5 N⋅m (1.8±0.5 kg-m, 13.0±3.6 ft-lb)
B2M0313
5) Tighten bolt which holds center exhaust pipe to hanger
bracket.
Tightening torque:
35±5 N⋅m (3.6±0.5 kg-m, 26.0±3.6 ft-lb)
B2M0312
6) Connect rear oxygen sensor connector. (Except Califor-
nia 2200 cc model)
B2M0725
7) Lower the vehicle.
8) Connect rear oxygen sensor connector. (California
2200 cc model)
B2M0724
9) Connect front oxygen sensor connector.
4
2-1SERVICE PROCEDURE
1. Front Catalytic Converter

B2M0312
2. Rear Catalytic Converter
A: REMOVAL
1) Lift-up the vehicle.
2) Disconnect rear oxygen sensor connector. (Except Cali-
fornia 2200 cc model)
B2M0055
3) Separate center exhaust pipe and rear catalytic con-
verter assembly from rear exhaust pipe.
B2M0421
4) Separate center exhaust pipe and rear catalytic con-
verter assembly from front catalytic converter.
B2M0313
5) Remove center exhaust pipe and rear catalytic con-
verter assembly from hanger bracket.
CAUTION:

Be careful not to pull down center exhaust pipe.

After removing center exhaust pipe, do not apply
excessive pulling force on front catalytic converter
and front exhaust pipe.
B2M0313
B: INSTALLATION
CAUTION:
Replace gaskets with new ones.
1) Install center exhaust pipe and rear catalytic converter
assembly.
Temporarily tighten bolt which installs center exhaust pipe
to hanger bracket.
5
2-1SERVICE PROCEDURE
2. Rear Catalytic Converter

B2M0421
2) Install center exhaust pipe to front catalytic converter.
Tightening torque:
35±5 N⋅m (3.6±0.5 kg-m, 26.0±3.6 ft-lb)
B2M0055
3) Install center exhaust pipe to rear exhaust pipe.
Tightening torque:
18±5 N⋅m (1.8±0.5 kg-m, 13.0±3.6 ft-lb)
B2M0313
4) Tighten bolt which holds center exhaust pipe to hanger
bracket.
Tightening torque:
35±5 N⋅m (3.6±0.5 kg-m, 26.0±3.6 ft-lb)
B2M0312
5) Connect rear oxygen sensor connector. (Except Califor-
nia 2200 cc model)
G2M0375
3. Canister
A: REMOVAL AND INSTALLATION
1. 2200 cc FWD AND 2500 cc MODEL
1) Disconnect canister hoses from evaporation pipes.
2) Remove canister with bracket.
6
2-1SERVICE PROCEDURE
2. Rear Catalytic Converter - 3. Canister

B2M0421
2) Install center exhaust pipe to front catalytic converter.
Tightening torque:
35±5 N⋅m (3.6±0.5 kg-m, 26.0±3.6 ft-lb)
B2M0055
3) Install center exhaust pipe to rear exhaust pipe.
Tightening torque:
18±5 N⋅m (1.8±0.5 kg-m, 13.0±3.6 ft-lb)
B2M0313
4) Tighten bolt which holds center exhaust pipe to hanger
bracket.
Tightening torque:
35±5 N⋅m (3.6±0.5 kg-m, 26.0±3.6 ft-lb)
B2M0312
5) Connect rear oxygen sensor connector. (Except Califor-
nia 2200 cc model)
G2M0375
3. Canister
A: REMOVAL AND INSTALLATION
1. 2200 cc FWD AND 2500 cc MODEL
1) Disconnect canister hoses from evaporation pipes.
2) Remove canister with bracket.
6
2-1SERVICE PROCEDURE
2. Rear Catalytic Converter - 3. Canister

G2M0066
9) Drain engine oil.
Set container under the vehicle, and remove drain plug
from oil pan.
B2M0312
10) Disconnect connector from rear oxygen sensor.
(Except California 2200 cc model)
B2M0054
11) Remove front exhaust pipe.
(1) Separate front catalytic converter from center
exhaust pipe.
(2) Remove front exhaust pipe from engine.
(3) Remove bolt which installs front exhaust pipe on
bracket.
B2M0743A
12) Remove nuts which install front cushion rubber onto
front crossmember.
G2M0081
13) Remove bolts which install oil pan on cylinder block
while raising up engine.
14) Insert oil pan cutter blade between cylinder block-to-oil
pan clearance.
CAUTION:
Do not use a screwdriver or similar tool in place of oil
pan cutter.
10
2-4SERVICE PROCEDURE
2. Oil Pan and Oil Strainer

B2M0054
9) Install front exhaust pipe.
CAUTION:
Always use the new gaskets.
(1) Place front exhaust pipe on bracket.
(2) Tighten nuts which install front exhaust pipe on
engine.
Tightening torque:
30±5 N⋅m (3.1±0.5 kg-m, 22.4±3.6 ft-lb)
B2M0055
(3) Tighten nuts which install front catalytic converter to
center exhaust pipe.
Tightening torque:
35±5 N⋅m (3.6±0.5 kg-m, 26.0±3.6 ft-lb)
B2M0056
(4) Tighten bolt which installs front exhaust pipe on
bracket.
Tightening torque:
24±3 N⋅m (2.4±0.3 kg-m, 17.4±2.2 ft-lb)
B2M0312
10) Connect connector to rear oxygen sensor. (Except
California 2200 cc model)
B2M0053
11) Lower the vehicle.
CAUTION:
At this time, lower lifting device and release steel
cables.
12) Remove lifting device and steel cables.
13
2-4SERVICE PROCEDURE
2. Oil Pan and Oil Strainer