knob SUBARU LEGACY 1996 Service Repair Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 1996, Model line: LEGACY, Model: SUBARU LEGACY 1996Pages: 2890, PDF Size: 61.9 MB
Page 945 of 2890
1. Manual Transmission
1. AWD MODEL
B3M0005B
1Gear shift knob
2Console boot
3Boot plate
4Gear shift lever
5Bush
6Spacer
7Locking wire
8Boot
9Snap ring
10O-ring
11Bush
12Cushion rubber
13Boss
14Joint
15Rod
16Bracket
17Spring
18Washer
19Stay
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 4.4±1.5 (0.45±0.15, 3.3±1.1)
T2: 5 (0.51, 3.7)
T3: 12±3 (1.2±0.3, 8.7±2.2)
T4: 18±5 (1.8±0.5, 13.0±3.6)
T5: 24.5±2 (2.50±0.20, 18.07±1.48)
2
3-3COMPONENT PARTS
1. Manual Transmission
Page 946 of 2890
2. FWD MODEL
B3M0006B
1Gear shift knob
2Console boot
3Boot plate
4Gear shift lever
5Bush
6Spacer
7Locking wire
8Boot
9Snap ring
10O-ring
11Bush
12Cushion rubber
13Boss
14Joint
15Rod
16Bracket
17Spring
18Stay
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 4.4±1.5 (0.45±0.15, 3.3±1.1)
T2: 5 (0.51, 3.7)
T3: 12±3 (1.2±0.3, 8.7±2.2)
T4: 18±5 (1.8±0.5, 13.0±3.6)
T5: 29±5 (3.0±0.5, 21.7±3.6)
3
3-3COMPONENT PARTS
1. Manual Transmission
Page 953 of 2890
G3M0695
9) Mount the following parts on the rod.
1Bush
2Spacer
CAUTION:
Apply grease [NIGLUBE-R or equivalent] to inner
and side surfaces of the bush when installing spacers.
The rod should be installed in the direction shown in
the figure.
10) Check that there is no excessive play and that parts
move smoothly.
B3M0010
E: INSTALLATION
1) Put into gearshift lever from passenger compartment.
2) Mount boot plate on the body.
3) Install console box and gearshift knob.
G3M0684
4) Mount cushion rubber on the body.
Tightening torque:
18±5 N⋅m (1.84±0.51 kg-m, 13.3±3.7 ft-lb)
G3M0697
5) Connect rod to the joint.
Tightening torque:
FWD model
12±3 N⋅m (1.2±0.3 kg-m, 8.7±2.2 ft-lb)
AWD model
18±5 N⋅m (1.84±0.51 kg-m, 13.3±3.7 ft-lb)
10
3-3SERVICE PROCEDURE
1. Manual Transmission
Page 1362 of 2890
4. Control Unit
1. LHD MODEL
B4M0369A
1Back plate
2Bulb
3Fan switch ASSY
4Illumi. plate
5Switch base
6Control panel
7Fan switch knob
8RECIRC switch
9A/C switch
10Temp. switch knob
11Mode switch
12Temp. lever ASSY
13Base plate
14Control amp.
15Temp. control cable
9
4-6COMPONENT PARTS
4. Control Unit
Page 1363 of 2890
2. RHD MODEL
B4M0057A
1Back plate
2Bulb
3Fan switch ASSY
4Illumi. plate
5Switch base
6Control panel
7Fan switch knob
8RECIRC switch
9A/C switch
10Temp. switch knob
11Mode switch
12Temp. lever ASSY
13Base plate
14Control amp.
15Temp. control cable
10
4-6COMPONENT PARTS
4. Control Unit
Page 1462 of 2890
1. Hood
The hood lock has a dual locking design which consists of
a main lock and a safety lock mechanism. When the
release knob located at the front pillar on the driver’s side
is pulled back, the main lock is released through the cable
attached to the knob.
The safety lock can be released by pushing the lever pro-
truding above the front grill while opening the hood.
G5M0137
A: REMOVAL
1. HOOD
1) Open front hood, and remove washer hose.
2) Remove attaching bolts.
3) Detach front hood from hinges.
B5M0267
2. HOOD LOCK
1) Open front hood and remove front grille.
2) Remove bolts which secure lock assembly to radiator
panel, and remove lock assembly.
3) Disconnect release cable from lock assembly.
B5M0319
3. RELEASE CABLE
1) Remove front grille.
2) Remove release cable from opener lever in passenger
compartment.
3) Remove release cable from lock assembly.
4) Remove cable clip from engine compartment.
G5M0140
B: POINTS TO CHECK
1) Check striker for bending or abnormal wear.
2) Check safety lever for improper movement.
3) Check other levers and spring for rust formation and
unsmooth movement.
33
5-1SERVICE PROCEDURE
1. Hood
Page 1551 of 2890
G5M0342
1. Front Seat
A: REMOVAL
1) While operating knob (located on top of backrest), lift
headrest out with hand placed between backrest and head-
rest.
2) Pull reclining lever back to fold backrest all the way for-
ward. While pulling slide adjuster lever, move seat all the
way forward.
B5M0332
3) Disconnect connector under driver’s seat.
4) Remove bolt cover at rear end of slide rail.
5) Remove bolts securing seat rear.
G5M0344
6) While pulling slide adjuster lever, slide seat all the way
back.
7) Remove bolts securing front of seat.
8) Remove front seat from vehicle, then install headrest.
CAUTION:
Be careful not to scratch seat when removing it from
vehicle.
G5M0342
B: INSTALLATION
1) While operating knob (located on top of backrest), lift
headrest out with hand placed between backrest and head-
rest.
2) Pull reclining lever back to fold backrest all the way for-
ward. Pull slide adjuster lever and move lower slide rail all
the way backward.
8
5-3SERVICE PROCEDURE
1. Front Seat
Page 1554 of 2890
G5M0350
2. WAGON MODEL
1) Remove bolts securing hinges (located at front of seat)
to body.
2) Pull strap (located in middle rear portion of cushion) to
release lock. Lift cushion out and away from body.
3) Pull knobs (located at each side of backrest’s upper
portion) up to release lock, and fold backrest all the way
forward.
B5M0333A
4) Remove the bolt1and then remove backrest. (LH
side)
5) Remove the bolt
2and then remove backrest (RH side)
from hinge bracket
3.
G5M0348
G5M0345
B: INSTALLATION
1. SEDAN MODEL
1) Before installing backrest, ensure that trim panel, insu-
lator and seat belt are properly installed.
2) Transfer outer seat belt webbing to front of backrest and
fold backrest forward. Attach seat wire to upper hooks (2
places), and move pillow in the direction of“B”until back-
rest is aligned with lower mounting holes in body.
3) Engage backrest’s folding mechanism with striker.
4) Secure lower center and both sides of backrest to body
with bolts.
5) Slightly raise front section of cushion while pushing
down on cushion in the direction of“C”. With cushion held
in that position, attach rear section of cushion to hooks at
lower frame location.
6) Secure front of cushion to body with bolts.
CAUTION:
Before installing seat, ensure that seat belt is placed
on cushion.
Confirm that winding of three-point type seat belt
can operate regularly.
10
5-3SERVICE PROCEDURE
2. Rear Seat
Page 1566 of 2890
1. Instrument Panel
Airbag system wiring harness is routed near combination
meter.
CAUTION:
All Airbag system wiring harness and connectors
are colored yellow. Do not use electrical test equip-
ment on these circuits.
Be careful not to damage Airbag system wiring har-
ness when servicing the combination meter.
B5M0022A
A: REMOVAL
1) Disconnect GND cable from battery.
2) Remove shift knob (MT model).
3) Remove console cover
1and front cover2.
B5M0023
4) Remove console box.
B5M0024A
5) Remove lower cover and then disconnect connector.
B5M0025
6) Remove glove box.
5
5-4SERVICE PROCEDURE
1. Instrument Panel
Page 1667 of 2890
G6M0107
5) Remove screws which secure switch and remove
switch.
CAUTION:
During installation (with key interlock)
When routing combination switch harness around
steering system, do not place it over key interlock
release knob.
After installing lower column cover, ensure that key
interlock release knob is accessible.
B6M0237
C: DISASSEMBLY AND ASSEMBLY
1. COMBINATION SWITCH
1) Remove screws which secure slip ring to combination
switch, and remove slip ring.
G6M0109
2) Remove screws which secure lighting switch, wiper and
washer switch. Remove both switches.
Assembly is in the reverse order of disassembly.
D: INSPECTION
1. COMBINATION SWITCH (ON-CAR)
1) Remove instrument panel lower cover.
2) Remove lower column cover.
11
6-2SERVICE PROCEDURE
4. Headlight