brake SUBARU LEGACY 2000 3.G User Guide

Starting and operating7-17
–
CONTINUED –
shift normally. NOTE In some cases, depressing the brake pedal on a downhill grade
does not result in an automatic downshift to 3rd gear. This canhappen when the automatic transmission fluid temperature is
very low, for example, during driving shortly after the vehicle has
been parked for an extended period of time. When the ATF tem-perature has risen to a certain level, automatic downshift normal-ly takes place. In the meantime, downshift manually for enginebraking as required.Also, downshifting when braking downhill will not occur at
speeds above approximately 50 mph (80 km/h).
3 (Third)
This p osition is for using eng ine b raking when g oin g d own a hill or for
c limb ing a g rad e.
The transmission automatic ally shifts into a suitab le g ear from 1st to
3rd ac c ord ing to the vehic le sp eed and the ac c elera tion you req uire.
When more ac c eleration is req uired in this p osition , p ress the ac c eler-
ator p ed al fully to the floor and hold that p ositio n. The transmission
will automatic ally d ownshift to 2nd or 1st g ear. Wh en you release the
p ed al, the transmission will return to the orig inal g ear p osition.
2 (Second)
This p osition is for using eng ine b raking when g oin g d own a hill or for
c limb ing a steep g rad e.
In this p osition, the transmission hold s in the 2nd g ear.
Use this p osition when starting off from a stand sti ll on slip p ery road
surfac es suc h as mud or snow. It will ensure g reate r trac tion.
1 (First)
This p osition is for d riving up or d own very steep g rad es, or d riving
throug h mud or sand , or on slip p ery surfac es. In th is p osition, the
transmission hold s in the 1st g ear.

7-18
Maximum speeds
WARNING
When shifting down a gear, ensure that the vehicle is not travel- ling at a speed exceeding the Maximum Allowable Speed for thegear which is about to be selected. Failure to observe this pre-caution can lead to engine over-revving and this in turn canresult in engine damage.In addition, sudden application of engine brakes when the vehicleis travelling on a slippery surface can lead to wheel locking; as a
consequence, control of the vehicle may be lost and the risk ofan accident increased.
The following tab les show the maximum sp eed s that a re p ossib le with
eac h d ifferent g ear. The tac hometer ’s (if so eq uip p ed ) need le will
enter the red area if these sp eed s are exc eed ed .
When shifting d own a g ear, it is imp ortant to c onfi rm that the c urrent
vehic le sp eed is not in exc ess of the Maximum Allow ab le Sp eed of
the g ear whic h is ab out to b e selec ted .
Exc eed ing the Maximum Allowab le Sp eed s will result in over-revving
of the eng ine. In ad d ition a p owerful eng ine b rake will eng ag e and
c ontrol of the vehic le may b e lost.
mph (km/h)
Vehicle type
PositionBrighton, LGTOUTBACK
133 (53)27 (43)29 (47)
264 (103)57 (92)62 (100)
3102 (164)97 (156)104 (167)
NOTE In order to prevent over-revving during acceleration of the
vehicle, the transmission will automatically shift to the next high- est gear if the Maximum Allowable Speed for the current gear isexceeded.

Starting and operating7-21
–
CONTINUED –
Braking
Braking tips
WARNING
Never rest your foot on the brake pedal while driving. This can
cause dangerous overheating of the brakes and needless wearon the brake pads and linings.
When the brakes get wet
When d riving in rain or after washing the vehic le, the b rakes may g et
wet. As a result, b rake stop p ing d istanc e will b e l ong er. To d ry the
b rakes, d rive the vehic le at a safe sp eed while lig htly d ep ressing the
b rake p ed al to heat up the b rakes. Use of engine braking
Rememb er to make use of eng ine b raking in ad d ition to foot b raking .
When d esc end ing a g rad e, if only the foot b rake is used , the b rakes
may start working imp rop erly b ec ause of b rake fluid overheating ,
c aused b y overheated b rake p ad s. To help p revent th is, shift into a
lower g ear to g et strong er eng ine b raking . Braking when a tire is punctured
Do not d ep ress the b rake p ed al sud d enly when a tire is p unc tured .
This c ould c ause a loss of c ontrol of the vehic le. Keep d riving straig ht
ahead while g rad ually red uc ing sp eed . Then slowly p ull off the road
to a safe p lac e.
Brake system Two separate circuits
Your vehic le has two sep arate c irc uit b rake systems . Eac h c irc uit
works d iag onally ac ross the vehic le. If one c irc uit of the b rake system
should fail, the other half of the system still wor ks. If one c irc uit fails,
the b rake p ed al will g o d own muc h c loser to the flo or than usual and
you will need to p ress it d own muc h hard er. And a m uc h long er d is-
tanc e will b e need ed to stop the vehic le.

7-22
Brake booster
The b rake b ooster uses eng ine manifold vac uum to as sist b raking
forc e. Do not turn off the eng ine while d riving b ec ause that will turn off
the b rake b ooster, resulting in p oor b raking p ower.
The b rakes will c ontinue to work even when the b rak e b ooster c om-
p letely stop s func tioning . If this hap p ens, however , you will have to
p ush the p ed al muc h hard er than normal and the b rak ing d istanc e
will inc rease.
Disc brake pad wear warning indicators
OM-H0163
The d isc b rake p ad wear warning ind ic ators on the d isc b rakes g ive a
warning noise when the b rake p ad s are worn.
If a sq ueaking or sc rap ing noise is heard from the d isc b rakes while
b raking , immed iately have your vehic le c hec ked b y y our SUBARU d eal-
er.

Starting and operating7-23
–
CONTINUED –
ABS (Anti-lock Brake System)
WARNING
Always use the utmost care in driving – overconfidence because
you are driving with an ABS equipped vehicle could easily lead to a serious accident.
CAUTION
The ABS system does not always decrease stopping distance.
You should always maintain a safe following distance from othervehicles. When driving on badly surfaced roads, gravel roads, icy road,
or over deep newly fallen snow, stopping distances may be long-er for a vehicle with the ABS system than one without. When driv-ing under these conditions, therefore, reduce your speed and
leave ample distance from other vehicles. When you feel the ABS system operating, you should maintain
constant brake pedal pressure. Do not pump the brake pedal
since doing so may defeat the operation of the ABS system.
The ABS system p revents the loc k-up of wheels whic h may oc c ur d uring
sud d en b raking or b raking on slip p ery road surfac es . This help s p revent
the loss of steering c ontrol and d irec tional stab il ity c aused b y wheel
loc k-up .
When the ABS system is op erating , you may hear a c h attering noise or
feel a slig ht vib ration in the b rake p ed al. This is normal when the ABS
op erates.
The ABS system will not op erate when the vehic le sp eed is b elow
ap p roximately 6 mp h (10 km/h).
ABS system self-check
You may feel a slig ht shoc k in the b rake p ed al and hear the op erating
sound of ABS from the eng ine c omp artment just after the vehic le is

Starting and operating7-25
–
CONTINUED –
but goes out immediately, remaining off.
The warning light remains on after the engine has been
started, but it goes out when the vehicle speed reaches about 8mph (12 km/h). The warning light comes on during driving, but it goes out
immediately and remains off.
When d riving with an insuffic ient b attery voltag e s uc h as when the en-
g ine is jump started , the ABS warning lig ht may c om e on. This is d ue
to the low b attery voltag e and d oes not ind ic ate a malfunc tion. When
the b attery b ec omes fully c harg ed , the lig ht will g o out.
Parking your vehicle
WARNING
Never leave unattended children or pets in the vehicle. They
could accidentally injure themselves or others through inadver- tent operation of the vehicle. Also, on hot or sunny days, the tem-perature in a closed vehicle could quickly become high enoughto cause severe or possibly fatal injuries to them. Do not park the vehicle over flammable materials such as dry
grass, waste paper or rags, as they may burn easily if they comenear hot engine or exhaust system parts. Be sure to stop the engine if you take a nap in the vehicle. If
engine exhaust gas enters the passenger compartment, occu-pants in the vehicle could die from carbon monoxide (CO) con-tained in the exhaust gas.
CAUTION
Never drive while the parking brake is set because this will cause
unnecessary wear on the brake linings. Before starting to drive,always make sure that the parking brake has been fully released.
To set the p arking b rake, p ress the b rake p ed al fir mly and hold it d own

8-12When the vehic le has b een left p arked after use on
road s heavily c ov-
ered with snow, or has b een left p arked d uring a sn owstorm, ic ing
may d evelop on the b rake system, whic h c ould c ause p oor b raking
ac tion. Chec k for snow or ic e b uild up on the susp en sion, d isc b rakes
and b rake hoses und erneath the vehic le.
If there is c aked snow or ic e, remove it, b eing c ar eful not to d amag e
the d isc b rakes and b rake hoses and ABS harness. n Refueling in cold weather
To help p revent moisture from forming in the fuel s ystem and the risk
of its freezing , use of an antifreeze ad d itive in t he fuel tank is rec om-
mend ed d uring c old weather.
Use only ad d itives that are sp ec ific ally d esig ned f or this p urp ose.
When an antifreeze ad d itive is used , its effec t las ts long er if the tank is
refilled whenever the fuel level reac hes half emp ty .
If your SUBARU is not g oing to b e used for an exten d ed p eriod , it is
b est to have the fuel tank filled to c ap ac ity. Driving on snowy and icy roads
WARNING
Do not use the cruise control on slippery roads such as snowy or icy roads. This may cause loss of vehicle control.
To p revent skid d ing and slip p ing , avoid sud d en b rak ing , ab rup t ac -
c eleration, hig h-sp eed d riving , and sharp turning w hen d riving on
snowy or ic y road s.
Always maintain amp le d istanc e b etween your vehic le and the vehic le
ahead of you to avoid the need for sud d en b raking .
To sup p lement the foot b rake, use the eng ine b rake effec tively to c on-
trol the vehic le sp eed . (Shift into a lower g ear wh en nec essary.)
Avoid shifting d own ab rup tly. Suc h b ehavior c an c au se the wheels to
loc k, p ossib ly lead ing to loss of vehic le c ontrol.
An anti-loc k b rake system (ABS) e nhanc es your vehic le’s braking perfor-
manc e on snowy and ic y road s. Refer to the “ABS (Anti-Loc k Brake Sys-
tem) ” section in chapter 7 for information on b raking on slip p ery sur-
fac es.

8-22Trailer hitch (if equipped)
WARNING
Never exceed the maximum weight specified for the trailer
hitch. Exceeding the maximum weight could cause an accident resulting in serious personal injuries. Permissible trailer weight
changes depending on the situation. Refer to the next section“ Trailer towing ” for possible recommendations and limitations.
Trailer brakes are required when the towing load exceeds
1,000 lbs. (453 kg). Be sure your trailer has safety chains and that
each chain will hold the trailer ’s maximum gross weight. Towing
trailers without safety chains could create a traffic safety hazardif the trailer separates from the hitch due to coupling damage orhitch ball damage. Be sure to check the hitch pin and safety pin for positive lock-
ing placement before towing a trailer. If the ball mount comes off
the hitch receiver, the trailer could get loose and create a trafficsafety hazard. Use only the ball mount supplied with this hitch. Use the hitch
only as a weight carrying hitch. Do not use with any type ofweight distributing hitch.
The trailer hitc h is d esig ned to tow a Class 1 rate d load . A maximum of
2,000 lbs. (906 kg) g ross trailer weig ht and a maximum of 200 lbs. (90
kg) g ross tong ue weig ht are p ermissib le for the traile r hitc h.
When you tow a trailer, follow the instruc tions in the next sec tion “Trailer
towing ”.

Driving tips8-27
–
CONTINUED –
CAUTION
Adequate size trailer brakes are required when the trailer and
its cargo exceed 1,000 lbs (453 kg) total weight. Before towing a trailer, check the trailer total weight, GVW,
GAWs and tongue load. Make sure the load and its distribution inyour vehicle and trailer are acceptable.
n Total trailer weight
The total trailer weig ht (trailer weig ht p lus its c arg o load ) must never
exc eed the maximum weig ht shown b elow.
Model
ConditionsMaximum totaltrailer weight
MT modelsWhen towing a trailer without brakes.1,000 lbs (453 kg)
When towing a trailer with brakes.2,000 lbs (906 kg)
AT modelsWhen towing a trailer without brakes.1,000 lbs (453 kg)
When towing a trailer with brakes.2,000 lbs (906 kg)
When towing a trailer on a long uphill grade continuously for over 5 miles (8 km) with an outside temperature of 104 F
(40 C) or above.1,000 lbs (453 kg)
OM-H2781
Total trailer weight

Driving tips8-31
–
CONTINUED –

Trailer hitches
WARNING
Never drill the frame or under-body of your vehicle to install a
commercial trailer hitch. If you do, dangerous exhaust gas, wateror mud may enter the passenger compartment through the drilledhole. Exhaust gas contains carbon monoxide, a colorless andodorless gas which is dangerous, or even lethal, if inhaled. Also,drilling the frame or under-body of your vehicle could cause dete-rioration of strength of your vehicle and cause corrosion aroundthe drilled hole.
CAUTION
Do not modify the vehicle exhaust system, brake system, or
other systems when installing a hitch or other trailer towingequipment. Do not use axle-mounted hitches as they can cause damage to
the axle housing, wheel bearings, wheels or tires.
Choose a p rop er hitc h for your vehic le and trailer. OUTBACK wagon
The use of a g enuine SUBARU trailer hitc h is rec omm end ed . A g enu-
ine SUBARU hitc h is availab le from your SUBARU d eal er.
If use of a non-g enuine hitc h is unavoid ab le, b e su re the hitc h is
suited to your vehic le and trailer. Consult with a p rofessional hitc h
sup p lier to assist you in c hoosing an ap p rop riate h itc h for your
vehic le. Be sure to follow all of the hitc h manufac turer’s instruc tions for
installation and use.
Never use a hitc h that mounts only to the rear b ump er. The b ump er is
not d esig ned to hand le that typ e of load .
For all typ es of hitc hes, reg ularly c hec k that the hitc h mounting b olts
and nuts are tig ht.