reset SUBARU LEGACY 2001 3.G Owners Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2001, Model line: LEGACY, Model: SUBARU LEGACY 2001 3.GPages: 453, PDF Size: 4.61 MB
Page 111 of 453
Keys and doors2-13
–
CONTINUED –
Security system (if equipped)
The sec urity system help s to p rotec t your vehic le a
nd valuab les from
theft. The horn sound s and the p arking lig hts flash if someone attemp ts
to b reak into your vehic le. The starter motor is al so interrup ted to p revent
starting the vehic le without a key.
The system c an b e armed and d isarmed with the remot e transmitter.
The system d oes not op erate when the key is inserte d into the ig nition
switc h.
System operation
The sec urity system will g ive the following alarm i nd ic ations when trig -
g ered : The p arking lig hts will flash and the horn will sou nd intermittently.
In ad d ition, the starter motor will not op erate. The alarm automatic ally resets after 30 sec ond s; ho wever, the
alarm will reac tivate if the vehic le is tamp ered wi th ag ain. The alarm
will c ontinue for twelve times if any sensor c ontin ues to b e ac tivated .
The alarm is trig g ered b y: Op ening a d oor, the rear g ate or trunk lid .
Ap p lic ation of p hysic al shoc k to the vehic le (e.g . b reaking g lass or
forc ed entry). Note that there are two alarm levels for shoc k: warning
and alarm. In warning mod e, the alarm d etec ts lower level vib rations
and trig g ers 2 warning c hirp s on the horn and two f lashes on the
lig hts as a d eterrent to would b e vand als. In alarm mod e, hig her lev-
els of shoc k are d etec ted and the system will g o in to full alarm.
Ig nition switc h b eing turned on while in armed stat e.
Page 163 of 453
3-34n
Compass zone adjustment
HB6021AB
1. The zone setting is fac tory p reset to Zone 8. Ref er to the “Com-
p ass c alib ration zone ” map shown ab ove or one attac hed to the end
of this manual to verify that the c omp ass zone sett ing is c orrec t for
your g eog rap hic al loc ation.
2. Press and hold the rig ht b utton for 3 sec ond s the n release, and the
word “ZONE ” will b riefly ap p ear and then the zone numb er will b e d is-
p layed .
3. Press the rig ht hand b utton rep eated ly to c yc le t he d isp lay throug h
all p ossib le zone setting s. Stop c yc ling when the c orrec t zone setting
for your loc ation is d isp layed .
4. Releasing the b utton for 3 sec ond s will exit the zone setting mod e.
Outside mirrors Convex mirror (Passenger side)
WARNING
Objects look smaller in a convex mirror and farther away than
when viewed in a flat mirror. Do not use the convex mirror tojudge the distance of vehicles behind you when changing lanes.
Use the inside mirror (or glance backwards) to determine theactual size and distance of objects that you view in convex mir-
ror.
Page 193 of 453
Audio5-7
–
CONTINUED –
Type A and B audio set (if equipped)
Typ e A: Without weather b and
Typ e B: With weather b and
The aud io set will op erate only when the ig nition s
witc h is in the “ACC ” or
“ ON ” p osition.
Radio operation
HB5041BB
1 Power switc h/Volume, Tone,
Balanc e, Fad er c ontrol d ial
2 AUDIO b utton
3 BAND b utton 4
Tuning b uttons
5 Preset b uttons
6 SCAN b utton
Power switch and volume/bass/treble/fader/balance control
n Power switch and volume control (PWR/VOL)
The d ial 1 is used for b oth p ower (ON/OFF) and volume c ontrol . The
rad io is turned ON and OFF b y p ushing the d ial and the volume is
c ontrolled b y turning the d ial.
Page 196 of 453
5-10Press the
“SCAN ” b utton ag ain to c anc el the SCAN mod e and to stop
on any d isp layed freq uenc y.
When the “SCAN ” b utton is p ressed for automatic tuning , stations a re
sc anned in the d irec tion of low freq uenc ies to hig h freq uenc ies only.
Automatic tuning may not func tion p rop erly if the s tation rec ep tion is
weakened b y d istanc e from the station or p roximity to tall b uild ing s
and hills. Selecting preset stations
Presetting a station with a “p reset b utton ”
5 allows you to selec t that
station in a sing le op eration. Up to six WB (if eq u ip p ed ), AM, FM1 and
FM2 stations eac h may b e p reset. How to preset stations
1. Press the “BAND ” b utton 3 to selec t FM1, FM2, AM or WB (if
eq uip p ed ) rec ep tion.
2. Press the “SCAN ” b utton or tune the rad io manually until the
d esired station freq uenc y is d isp layed .
3. Press one of the p reset b uttons for more than 2 s ec ond s to store
the freq uenc y. At this time, there will momentarily b e no sound from
the rad io. If the b utton is p ressed for less than 2 sec ond s, the p rec ed -
ing selec tion will remain in memory.
NOTE If the connection between the radio and battery is broken for any
reason such as vehicle maintenance or radio removal, all stationsstored in the preset buttons are cleared. If this occurs, it is neces-sary to reset the preset buttons.
Page 205 of 453
Audio5-19
–
CONTINUED –
Type C audio set (if equipped)
The rad io will op erate only when the ig nition switc
h is in the “ACC ” or
“ ON ” p osition.
Radio operation
HB5042BB
1 FM/AM selec tion b utton
2 SCAN b utton
3 WB (weather b and ) b utton
4 Tuning b uttons
5 Preset b uttons 6
Fad er/Balanc e selec tion
b utton
7 Power switc h, Volume c ontrol,
Bass/Mid d le/Treb le c ontrol and
Fad er/Balanc e c ontrol d ial
8 AUDIO (aud io mod e) b utton
Power switch and volume/bass/treble/fader/balance control (PWR/VOL)
The d ial 7 is used for b oth p ower (ON/OFF) and volume c ontrol . The
rad io is turned ON and OFF b y p ushing the d ial and the volume is
c ontrolled b y turning the d ial.