fog light SUBARU LEGACY 2004 4.G User Guide

4-11
Climate control
– CONTINUED –
2. Set the temperature control dial to the red area.
3. Set the fan speed control dial at the highest speed. Automatic climate control system (if
equipped)
NOTE y
Operate the automatic climate control system
when the engine is running. y When the engine coolant is cold, for instance in
cold weather, the air flows through the windshield
defroster outlets and the blower runs at the lowest
speed to prevent cold air from blowing directly
against the driver and front passenger.y In the “AUTO” mode, if the air temperature in the
passenger compartment is cooled down to the
specified temperature, the air conditioner com-
pressor stops automatically. For efficient defog-
ging or dehumidifying in cold weather, press the
“A/C” switch on.y Even when cooling is not necessary, setting the
temperature much lower than the current outlet air
temperature turns on the air conditioner compres-
sor automatically and the “A/C” indicator light on
the control panel comes on.
The automatic climate control system automatically
controls outlet air temperature, fan speed, air flow dis-
tribution air-inlet control, and air conditioner compres-
sor operation. It activates when the “AUTO” switch is

4-13
Climate control
– CONTINUED –
TAUTO switch
AUTO mode operation:
The Automatic Climate Control system automatically
controls the air temperature of the passenger com-
partment in the AUTO mode. When the “AUTO” switch
is pressed, the indicator light “AUTO” on the control
panel comes on. In this state, outlet air temperature,
fan speed, air flow distribution, air-inlet control, and air
conditioner compressor operation are automatically
controlled.
ECON (economy) mode:
When you press the “AUTO” switch while the system
is in the AUTO mode, it selects the ECON (economy)
mode, turning on the “ ” indicator light. In the
ECON mode, the compressor runs to be thrifty with
energy consumption. Interior windows tend to fog in
this energy-saving operation. It is therefore recom-
mended that the AUTO mode be used only in high hu-
midity conditions.
Manual mode operation:
When the Automatic Climate Control system is operat-
ing in the AUTO mode, pressing the “ ”,
“ ”, “MODE”,“A/C” or “ ” switch
shifts the operation into the “MANUAL” mode and the
indicator light “AUTO” on the control panel will go out.
When the “ ”, “ ”, “MODE”,“A/C” or “ ” switch is pressed, the corresponding func-
tion can be controlled independently, while automatic
control of the other functions are maintained.
To change the system back to the AUTO mode, press
the “AUTO” switch. T
OFF switch
The Automatic Climate Control system turns off (the
air conditioner compressor and fan turn off) when the
“OFF” switch is pressed.
When the “OFF” switch is pressed, the outside air in-
troduction mode (“ ” position) is automatically
selected.
NOTE
Display illumination dimness cancellation (BRIGHT):
Setting the light switch to the “ ” or “ ”
position causes the illuminating icons on the dis-
play panel to dim. When traveling with the lights
on in gloomy daylight or in twilight, press the OFF
switch for 1 second or longer if you feel it is too
hard to identify the icons clearly. The brightness
comes back to normal.
If you wish to dim the icons again, hold down the
OFF switch again or if you can safely do so, turn
the light switch OFF and then place it in the
“ ” or “ ” position.

4-14
Climate control
T
OUT.TEMP switch
To check the outside air temperature, push the
“OUT.TEMP” switch. The outside air temperature will
be displayed for five seconds, and then the display au-
tomatically changes back to the inside air tempera- ture.
The display changes over from the inside air tempera-
ture to the outside air temperature as its normal indi-
cation if you keep the switch pressed for more than 2seconds.
NOTE y The outside air temperature display shows the
outside air temperature in a range from –22 to
131 °F (–30 to 55 °C).
y You can check the outside air temperature even
when the Automatic Climate Control is off. (The ig-
nition switch should be in the “ON” position.) y In the following cases, the display can indicate a
higher temperature than the actual outside air
temperature: – In direct sunlight
– When the vehicle is parked for a long period of
time with the engine kept running.
– During stop and go driving
T – Defroster switch
To defrost or dehumidify the windshield and side win- dow, push the defroster switch “ ”. When the
“ ” switch is pushed, regardless whether the air
conditioner is operating or not, outside air is drawn into
the passenger compartment, the air conditioner com-
pressor turns on, air flow is directed towards the wind-
shield and side windows, and the indicator light
“ ” on the control panel comes on.
Even with the defroster switch pushed, you can turn
the air conditioner ON/OFF and select interior air recir-
culation or outside air introduction as desired.
After eliminating the fogging from the windshield, set
the air conditioner back in the AUTO mode by pushing
the “AUTO” switch or turn off by pushing the “OFF”
switch or “ ” switch.

4-15
Climate control
– CONTINUED –
T – Fan speed control switch
1) Fan speed control switch
The fan speed control switch has the 5 positions:
AUTO position and 4 different fan speed positions.
With the fan speed control switch in the AUTO posi-
tion, the fan speed changes automatically correspond-
ing to various conditions: air temperature inside and
outside of the passenger compartment, intensity of the
sunlight, etc.
Use this switch to select desired fan speed. Fan speed
increases with each press of the switch and returns to
the AUTO position. T
A/C – Air conditioner switch
NOTE
The air conditioner compressor does not operate
when the outside air temperature is below 32 °F
(0 °C).
If the windshield starts to fog when the air conditioner
is operated in the AUTO mode, push the air condition-
er switch “A/C” to defog and dehumidify.
When this switch is pushed, the air conditioner com-
pressor turns on and the indicator light “A/C” on the
control panel comes on. After eliminating the fogging
from the windshield, set the air conditioner back in the
AUTO mode by pushing the “AUTO” switch. T MODE – Air flow control switch
(Ventilation): Air flows through the instrument pan-
el outlets.
(Bi-level): Air flows through the instrument panel
outlets and the foot outlets.
(Heat): Air flows through the foot outlets and
some through the windshield defroster outlets.
1
AUTO 1 2 3 4UB5021BB

4-16
Climate control
(Heat-def): Air flows through the windshield de-
froster outlets and foot outlet.
NOTE
When the “ ” mode is selected, the air condi-
tioner compressor operates automatically regard-
less of the position of the air conditioner button to
defog the windshield quickly. At the same time,
the air inlet selection is automatically set to “” mode.
Even with this mode selected, you can turn the air
conditioner ON/OFF and select interior air recircu-
lation or outside air introduction as desired. T Air inlet selection switch
Continued operation in the “ ” position
may fog up the windows. Switch to the
“ ” position as soon as the outside
dusty condition clears. A) Outside air is drawn into the passenger’s compart-
ment.
B) Interior air recirculates inside the passenger’s com- partment.
1) Air inlet selection switch
Select the air inlet by pushing the air inlet selection switch. : Interior air recirculates inside the passenger’s
compartment. Use this position when quickly warming
up the passenger compartment or cooling it down or
when preventing outside air from entering the passen-
ger compartment from the outside air. The indicator
light “ ” on the control panel comes on when
AB
1
UB4032BB

10-1
10
Appearance care
Exterior care .................................................. 10-2 Washing ............................................................. 10-2
Waxing and polishing ....................................... 10-3
Cleaning aluminum wheels .............................. 10-4
Cleaning fog light lens (for OUTBACK) .......... 10-4
Corrosion protection .................................... 10-5 Most common causes of corrosion ................ 10-5
To help prevent corrosion ............................... 10-6
Cleaning the interior ..................................... 10-7 Seat fabric ......................................................... 10-7
Leather seat materials ...................................... 10-7
Synthetic leather upholstery ........................... 10-7
Climate control panel, audio panel, instrument panel, console panel, switches,
combination meter, and other plastic
surface ............................................................ 10-8

10-4
Appearance care
„
Cleaning aluminum wheels
y Promptly wipe the aluminum wheels clean of any
kind of grime or agent. If dirt is left on too long, it may
be difficult to clean off.y Do not use soap containing grit to clean the wheels.
Be sure to use a neutral cleaning agent, and later rinse
thoroughly with water. Do not clean the wheels with a
stiff brush or expose them to a high-speed washing
device. y Clean the vehicle (including the aluminum wheels)
with water as soon as possible when it has been
splashed with sea water, exposed to sea breezes, or
driven on roads treated with salt or other agents. „
Cleaning fog light lens (for OUTBACK)
1. Stop the vehicle in a safe place.
2. Stop the engine and turn off the fog lights.
1) Counter-clockwise
2) Light lens horizontal center line
3. Check that the fog lights are not hot. Then, grasp
the protector and turn it approximately 10 ° counter-
clockwise.
4. Pull the protector off the fog light.
5. Wash the lens with water.
6. Apply the protector to the lens at an angle of ap-
proximately 10 ° from the fog light’s horizontal center
line. Then, turn the protector clockwise until it stops.
1
2
UBA017BB

10-5
Appearance care
– CONTINUED –
Finally, check that the protector’s horizontal bars are
parallel with the fog light’s horizontal center line.Corrosion protection
Your SUBARU has been designed and built to resist
corrosion. Special materials and protective finishes
have been used on most parts of the vehicle to help
maintain fine appearance, strength, and reliable oper-
ation. „Most common causes of corrosion
The most common causes of corrosion are:
1. The accumulation of moisture retaining dirt and de-
bris in body panel sections, cavities, and other areas.
2. Damage to paint and other protective coatings
caused by gravel and stone chips or minor accidents.
Corrosion is accelerated on the vehicle when:
1. It is exposed to road salt or dust control chemicals,
or used in coastal areas where there is more salt in the
air, or in areas where there is considerable industrial
pollution.
2. It is driven in areas of high humidity, especially
when temperatures range just above freezing.
3. Dampness in certain parts of the vehicle remains
for a long time, even though other parts of the vehicle
may be dry.
4. High temperatures will cause corrosion to parts of
the vehicle which cannot dry quickly due to lack of

11 - 2
Maintenance and service
Parking brake stroke .................................... 11-43
Tires and wheels .......................................... 11-43Types of tires .................................................... 11-43
Tire inspection .................................................. 11-44
Tire pressures and wear .................................. 11-44
Wheel balance ................................................... 11-47
Wear indicators ................................................. 11-47
Tire rotation ....................................................... 11-48
Tire replacement ............................................... 11-48
Wheel replacement ........................................... 11-49
Wheel covers .................................................... 11-50
Aluminum wheels (if equipped) .................. 11-51
Windshield washer fluid .............................. 11-51
Replacement of wiper blades ...................... 11-52 Replacement wiper blade assembly ............... 11-53
Replacement wiper blade rubber .................... 11-53
Battery ........................................................... 11-58
Fuses ............................................................. 11-59
Main fuse ....................................................... 11-61
Installation of accessories .......................... 11-62
Replacing bulbs ............................................ 11-63 Headlight ........................................................... 11-65
Front fog light (if equipped) ............................. 11-69
Front turn signal light, parking light and side marker light .................................................... 11-69
Rear combination lights ................................... 11-71
License plate light ............................................ 11-76
Map light, dome light, luggage compartment light and door step light ................................ 11-76
Trunk light ......................................................... 11-79
High mount stop light ...................................... 11-79

11 - 6 2
2Maintenance and service
Installation of accessories
Always consult your SUBARU dealer before installing
fog lights or any other electrical equipment in your ve-
hicle. Such accessories may cause the electronic sys-
tem to malfunction if they are incorrectly installed or if
they are not suited for the vehicle.