ignition SUBARU LEGACY 2004 4.G Owner's Manual

2-33
Keys and doors
– CONTINUED –
or extremely cold conditions have caused it to
freeze shut.
„ Tilting/sliding moonroof (Sedan)
The moonroof has both tilting and sliding functions.
The moonroof operates only when the ignition switch
is in the “ON” position.
1) Open/Close switch
2) Tilt switch
T To raise or lower the moonroof
The tilting function will only operate when the moon-
roof is fully closed. Push the rear side of the “Tilt” switch to raise the
moonroof.
Push the front side of the “Tilt” switch to lower the
moonroof.
Release the switch after the moonroof has been
raised or has been lowered completely. Pushing the
switch continuously may cause damage to the moon- roof. T
To open or close the moonroof
Push the “Open/Close” switch rearward to open the
moonroof. The sun shade will be also opened together
with the moonroof. Push the “Open/Close” switch forward to close the
moonroof. The moonroof will stop halfway if you con-
tinue to press on the switch.
Release the switch once and push it again to close the
moonroof completely.
After washing the vehicle or after it rains, wipe away
water on the roof prior to opening the moonroof to pre-
vent water drops from falling into the passenger com- partment.
NOTE
If the moonroof cannot be closed through the
switch operation because of system failure, it can
be closed manually using a hex-headed wrench.
1
2
UB2034BB

2-35
Keys and doors
– CONTINUED –
The front moonroof has a tilting function and the rear
moonroof has a sliding function.
Both moonroofs operate only when the ignition switch
is in the “ON” position.
1) Open
2) Close
To open the moonroof(s)
1. Open the front sunshade.
2. Continually push the rear side (OPEN) of the
switch, and the front moonroof will tilt up and stop au-tomatically.
3. If you want to open the rear moonroof as well, re-
lease the switch once and then push the rear side of the switch continuously.
The rear moonroof will begin to slide open together
with the rear sunshade, then stop automatically at 7.9
in (20 cm) in a partially open position.
4. To fully open it, release the switch once, then push
the rear side of the switch again and keep it depressed
until the full open position is reached.
To close the moonroof(s)
1. Push the front side (CLOSE) of the switch. The rear
moonroof will slide to close together with the rear sun-
shade while the switch is being pressed, then stop au-
tomatically at a position 5.9 in (15 cm) away from the
fully closed position.
2. To close the rear moonroof fully, release the switch
once, then push the front side of the switch continu-
ously again.
3. If you want to close the front moonroof as well,
push the switch again.
After washing the vehicle or after it rains, wipe away
water on the roof prior to opening the moonroof to pre-
vent water drops from falling into the passenger’s compartment.
NOTE y
Driving with the moonroof fully open can cause
a great deal of wind noise. If such a condition has
been encountered, close the moonroof up to the
1
2
UB2006BB

3-1
3
Instruments and controls
Ignition switch .............................................. 3-3 LOCK .................................................................. 3-3
ACC .................................................................... 3-4
ON ....................................................................... 3-5
START ................................................................ 3-5
Key reminder chime .......................................... 3-5
Ignition switch light .......................................... 3-5
Key interlock release (AT vehicles only) ........ 3-5
Hazard warning flasher ................................ 3-6
Meters and gauges ....................................... 3-7 Speedometer ..................................................... 3-7
Odometer/Trip meter ........................................ 3-7
Tachometer ........................................................ 3-8
Outside temperature indicator (if equipped) .. 3-8
Fuel gauge ......................................................... 3-8
Temperature gauge ........................................... 3-9
Warning and indicator lights ....................... 3-10 Seatbelt warning light and chime .................... 3-10
SRS airbag system warning light .................... 3-10
CHECK ENGINE warning light/Malfunction indicator lamp ................................................. 3-11
Charge warning light ........................................ 3-12
Oil pressure warning light ................................ 3-12
AT OIL TEMPerature warning light (for AT vehicles) ............................................. 3-12
ABS warning light ............................................. 3-13
VDC (Vehicle Dynamics Control) warning light (if equipped) ........................................... 3-13
Brake system warning light ............................. 3-14
Door open warning lights ................................. 3-15
Low fuel warning light ...................................... 3-15 Front-wheel drive warning light (for AT
vehicles except GT and vehicle with VDC) .. 3-15
VDC (Vehicle Dynamics Control) operation indicator light (if equipped) ........................... 3-15
VDC (Vehicle Dynamics Control) OFF indicator light (if equipped) ........................... 3-16
Security system status indicator light
(if equipped) .................................................... 3-16
Selector lever position indicator (AT vehicles) ................................................... 3-17
Gear position indicator (AT vehicle with SPORTSHIFT) ................................................. 3-17
Turn signal indicator lights .............................. 3-17
High beam indicator light ................................. 3-18
Cruise control set indicator light .................... 3-18
Clock .............................................................. 3-18
Light control switch ...................................... 3-19 Headlights ......................................................... 3-19
High/low beam change (dimmer) .................... 3-20
Headlight flasher ............................................... 3-20
Daytime running light system ......................... 3-21
Turn signal lever ........................................... 3-21
Illumination brightness control ................... 3-22
Parking light switch ...................................... 3-23
Fog light switch (if equipped) ...................... 3-24
Wiper and washer ......................................... 3-24 Windshield wiper and washer switches ......... 3-26
Rear window wiper and washer switch (if equipped) .................................................... 3-27
Rear window defogger switch ..................... 3-28

3-3
Instruments and controls
– CONTINUED –
Instruments and controlsIgnition switch
Never turn the ignition switch to “LOCK” while
the vehicle is being driven or towed because
that will lock the steering wheel, preventing
steering control. And when the engine is turned
off, it takes a much greater effort than usual to
steer.
The ignition switch has four positions: LOCK, ACC,
ON and START.
NOTE y Keep the ignition switch in the “LOCK” position
when the engine is not running. y Using electrical accessories for a long time with
the ignition switch in the “ON” or “ACC” position
can cause the battery to go flat.
If the ignition switch will not move from the “LOCK” position to the “ACC” position, turn the
steering wheel slightly to the left and right as youturn the ignition switch. y If the key is attached to a keyholder or to a large
bunch of other keys, centrifugal force may act on
it as the vehicle moves, resulting in unwanted
turning of the ignition switch. Also, if a large key-
holder is attached to the key, your knees or hands
may accidentally touch it in a way that turns the ig-
nition switch. „ LOCK
The key can only be inserted or removed in this posi-
tion. The ignition switch will lock the steering wheel
when you remove the key.
If turning the key is difficult, turn the steering wheel
slightly to the right and left as you turn the key.
UB4000CA

3-5
Instruments and controls
– CONTINUED –
„ON
This is the normal operating position after the engine
is started. „ START
Do not turn the ignition switch to the “START”position while the engine is running.
The engine is started in this position. The starter
cranks the engine to start it. When the key is released
(after the engine has started), the key automatically
returns to the “ON” position. „ Key reminder chime
The reminder chime sounds when the driver’s door
opens and the key is in the “LOCK” or “ACC” positions.
The chime stops when the key is removed from the ig- nition switch. „ Ignition switch light
For easy access to the ignition switch in the dark, the
ignition switch light comes on when driver’s door is opened. The light remains on for 10 seconds and goes
out after driver’s door is closed or if the key is turned
to the “ON” position. „
Key interlock release (AT vehicles
only)
If the key can not be turned to the “LOCK” position
even when the selector lever is in the “P” position:
1. Take out the screwdriver from the tool bag.
2. Remove the cover under the steering column using
a phillips screwdriver.
HS3016BA

3-6
Instruments and controls
3. Turn the ignition key while pressing the key inter-
lock release lever.
Take your vehicle to the nearest SUBARU dealer im-
mediately to have the key interlock system repaired.
Hazard warning flasher
The hazard warning flasher is used to warn other driv-
ers when you have to park your vehicle under emer-
gency conditions. The hazard warning flasher works with the ignition switch in any position.
To turn on the hazard warning flasher, push the haz-
ard warning button on the instrument panel. To turn off
the flasher, push the button again.
NOTE
When the hazard warning flasher is on, the turn
signals do not work.
UG3025BA
UB8002BA

3-9
Instruments and controls
– CONTINUED –
nition switch is in the “ACC” or “LOCK” position.
The gauge may move slightly during braking, turning
or acceleration due to fuel level movement in the tank. „Temperature gauge
If the pointer exceeds the normal operating
range, safely stop the vehicle as soon as possi-
ble.
See “In case of emergency” in chapter 9.
1) Normal operating range
The temperature gauge shows engine coolant temper-
ature when the ignition switch is in the “ON” position.
The coolant temperature will vary in accordance with
the outside temperature and driving conditions.
We recommend that you drive moderately until the
pointer of the temperature gauge reaches near the
middle of the range. Engine operation is optimum with
the engine coolant at this temperature range and high
revving operation when the engine is not warmed up
enough should be avoided.
1
UB2012BB

3-10
Instruments and controls
Warning and indicator lights
Several of the warning and indicator lights come on
momentarily and then go out when the ignition switch
is initially turned to the “ON” position. This permits
checking the operation of the bulbs.
Apply the parking brake and turn the ignition switch to
the “ON” position. The following lights come on:
Seatbelt warning light
SRS airbag system warning light
CHECK ENGINE warning light / Malfunction indica- tor lamp
Charge warning light
Oil pressure warning light
AT OIL temperature warning light (AT vehicles) ABS warning light
VDC warning light (if equipped)
VDC operation indicator light (if equipped)
VDC OFF indicator light (if equipped)
Brake system warning light
If any lights fail to come on, it indicates a burned-out
bulb or a malfunction of the corresponding system.
Consult your authorized SUBARU dealer for repair. „
Seatbelt warning light and chime
When the ignition switch is turned to the “ON” position,
the seatbelt warning light will come on and the remind-
er chime will sound for about six seconds to remind the
driver to fasten the seatbelt.
The seatbelt warning light remains on for about six
seconds and turns off automatically after six seconds.
The seatbelt reminder chime will turn off when the
driver’s side seatbelt is buckled or it will turn off auto- matically after six seconds. „ SRS airbag system warning light
When the ignition switch is turned to the “ON” position,
the SRS airbag system warning light will come on for
about six seconds and go out. This shows the SRS
frontal airbag and SRS side airbag (if equipped) and
seatbelt pretensioners are in normal operation.
If this light comes on while driving or remains illuminat-
ed even after a period of about 6 seconds from when
the ignition has been turned on, it may indicate that the
SRS frontal airbag system or SRS side airbag system
(if equipped) or seatbelt pretensioner system is not
working properly. Contact your nearest SUBARU
dealer immediately.

3-13
Instruments and controls
– CONTINUED –
„ABS warning light
The ABS warning light comes on when the ignition
switch is turned to the “ON” position and goes out after
about two seconds.
This is an indication that the ABS system is working
properly.
If the warning light behaves as follows, the ABS
system may not work properly.
When the warning light is on, the ABS function
shuts down; however, the conventional brake
system continues to operate normally. y The warning light does not come on when the
ignition switch is turned to the “ON” position. y The warning light comes on when the ignition
switch is turned to the “ON” position, but it
does not go out even when the vehicle speed
exceeds approximately 8 mph (12 km/h). y The warning light comes on during driving.
If these occur, have the ABS system repaired at
the first available opportunity by your SUBARU
dealer.
NOTE
If the warning light behavior is as described be-
low, the ABS system may be considered normal.y The warning light comes on right after the en-
gine is started but goes out immediately, remain-
ing off.y The warning light remains on after the engine
has been started, but it goes out when the vehicle
speed reaches about 8 mph (12 km/h).y The warning light comes on during driving, but
it goes out immediately and remains off.
When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning
light may come on. This is due to the low battery volt-
age and does not indicate a malfunction. When the
battery becomes fully charged, the light will go out. „ VDC (Vehicle Dynamics Control)
warning light (if equipped)
This warning light comes on when the ignition switch
is turned to the “ON” position and goes out after the
engine has started. It indicates that the VDC system is
operational.
The VDC system is probably inoperative under any of
the following conditions. Immediately have your vehi-
cle checked at a SUBARU dealer.(U.S.) (Canada)

3-14
Instruments and controls
y
The VDC warning light does not come on when the
ignition switch is turned to the “ON” position. y The VDC warning light remains on after the engine
has started and stays lit even when the vehicle speed
reaches about 8 mph (12 km/h).y The VDC warning light comes on while the vehicle
is running.y If the electrical circuit of the VDC system itself be-
comes faulty, the VDC warning light only comes on. At
this time, the ABS (Anti-lock Brake System) remains
fully operational.y The warning light comes on when the electronic
control system of the ABS/VDC system becomesfaulty.
The VDC system provides its ABS control through the
electrical circuit of the ABS system. Accordingly, if the ABS is inoperative, the VDC system also becomes un-
able to provide ABS control. As a result, the VDC sys-
tem becomes inoperative, causing the VDC warning
light to come on. Though both the VDC and ABS sys-
tems are inoperative in this case, the ordinary func-
tions of the brake system are still available. You will be
safe while driving with this condition, but you should
have your vehicle checked at a SUBARU dealer as
soon as possible.NOTE
If the warning light behavior is as described be-
low, the VDC system may be considered normal.y The warning light comes on right after the en-
gine is started but goes out immediately, remain-
ing off.y The warning light remains on after the engine
has been started, but it goes out when the vehicle
speed reaches 8 mph about (12 km/h).y The warning light comes on during driving, but
it goes out immediately and remains off. „ Brake system warning light
yDriving with the brake system warning light
on is dangerous. This indicates your brake sys-
tem may not be working properly. If the light re-
mains on, have the brakes inspected by a
SUBARU dealer immediately. y If at all in doubt about whether the brakes are
operating properly, do not drive the vehicle.
Have your vehicle towed to the nearest
SUBARU dealer for repair.
(U.S.) (Canada)