towing SUBARU LEGACY 2004 4.G Owner's Manual

9-21
In case of emergency
– CONTINUED –
dealer or a commercial towing service. Observe the
following procedures for safety. „Towing and tie-down hooks
The towing hooks should be used only in an emergen-
cy (e.g., to free a stuck vehicle from mud, sand or snow).
y Use only the specified towing hooks and tie-
down hooks. Never use suspension parts or
other body parts for towing or tie-down purpos-
es. y Never use the tie-down hook closest to the
muffler under the vehicle for towing purposes. y To prevent deformation to the front bumper
and the towing hook, do not apply excessive
lateral load to the towing hooks. 1) Towing hook cover
2) Towing hook
1
2
UB9048BB

9-22
In case of emergency
1) Towing hook cover
2) Towing hook
The front towing hook is located on the inside of the
towing hook cover below the right-hand headlight.
1) Tie-down hook
2) Towing and tie-down hook
1
2UB9051BB
1
11
2UB8013CB

9-23
In case of emergency
– CONTINUED –
Tie-down hook:
Vehicle with trailer hitch (if equipped)
1) Tie-down hook T
Towing hook cover removal procedure
For except OUTBACK models:
To use the towing hook, insert the top end of the flat
tip screwdriver in a slot on the upper part of the cover,
and remove the cover while prying it off.
Remove the towing hook cover by pulling it toward the
side of the vehicle and toward you.
1UB9010BB
UB9049BA

9-24
In case of emergency
For OUTBACK models:
1. Squeeze the sides of portion A and pull the towing
hook cover toward you.
UB9045BB
UB9042BA
B
UB9021CB

9-25
In case of emergency
– CONTINUED –
2. Press portion B and simultaneously pull the towing
hook cover toward you. 3. Turn the towing hook cover clockwise, pivoting it
about the side that is next to the fog lamp. Pull out the
towing hook cover to remove it.
UB9043BAUB9044AA

9-26
In case of emergency
T
Towing hook cover installation procedure
For except OUTBACK models:
Align the towing hook cover with its original installation
position and press all parts of it into place. For OUTBACK models:
1. Insert the projection
C into the hole D.
UB9052BA
C D
UB9044CB

9-28
In case of emergency
„
Towing with all wheels on the ground
yNever turn the ignition switch to the “LOCK”
position while the vehicle is being towed be-
cause the steering wheel and the direction of
the wheels will be locked.y Remember that the brake booster and power
steering do not function when the engine is not
running. Because the engine is turned off, it will
take greater effort to operate the brake pedal
and steering wheel.
y If transmission failure occurs, transport your
vehicle on a flat-bed truck. y Do not run the engine while being towed us-
ing this method. Transmission damage could
result if the vehicle is towed with the engine
running. y For vehicles with automatic transmission,
the traveling speed must be limited to less than
20 mph (30 km/h) and the traveling distance to
less than 31 miles (50 km). For greater speeds
and distances, transport your vehicle on a flat-
bed truck.
1. Check the transmission and differential oil levels
and add oil to bring it to the upper level if necessary.
2. Release the parking brake and put the transmis-
sion in neutral.
3. The ignition switch should be in the “ACC” position
while the vehicle is being towed.
4. Take up slack in the towline slowly to prevent dam-
age to the vehicle.UB8010AA

11 - 1 6
2Maintenance and service
API Service label
1) Indicates the oil quality by API designations
2) Indicates the SAE oil viscosity grade
3) Indicates that the oil has fuel saving capabilities
In choosing an oil, you want the proper quality and vis-
cosity, as well as one that will add to fuel economy.
The following table lists the recommended viscosities
and applicable temperatures.
When adding oil, different brands may be used togeth-
er as long as they are the same API classification and
SAE viscosity as those recommended by SUBARU. SAE viscosity number and applicable temperature
*: 5W-30 is preferred.
Engine oil viscosity (thickness) affects fuel economy.
Oils of lower viscosity provide better fuel economy.
However, in hot weather, oil of higher viscosity is re-
quired to properly lubricate the engine. „ Recommended grade and viscosity
under severe driving conditions
If the vehicle is used in desert areas, in areas with very
high temperatures, or used for heavy-duty applica-
tions such as towing a trailer, use of oil with the follow-
ing grade and viscosities is recommended.
APISERVICESL
ENERGYCONSERVING
SAE
5W
30
1
2
3
HSB022BB
5W-30*10W-30, 10W-40
-30 -20 -10 0 10 20 30 40
-20
06 0
20 80 100 40
HSB024BA

12-5
Specifications
– CONTINUED –
„Tires
„ Wheel alignment
Tire sizeP205/60R15 90HP205/55R16 89HP225/60R16 97H
Wheel size15 x 6JJ16 x 6 1
/2 JJ
PressureFront32 psi (220 kPa, 2.2 kg/cm 2
)30 psi (210 kPa, 2.1 kg/cm 2
)
Rear30 psi (210 kPa, 2.1 kg/cm 2
)29 psi (200 kPa, 2.0 kg/cm 2
)
Rear at trailer
towing–32 psi (220 kPa, 2.2 kg/cm 2
)
Temporary
spare tireSizeT135/70R16T145/80R16
Pressure60 psi (420 kPa, 4.2 kg/cm 2
)
ItemLegacyOUTBACK
SedanWagonSedanWagon
ToeFront0 in (0 mm)
Rear0 in (0 mm)
CamberFront–0 °05’0 °20’
Rear–0 °30’–0 °20’–0 °10’

13-5
Consumer information and Reporting safety defects
– CONTINUED –
„Recommended tire inflation pressure
T Recommended cold tire inflation pressure
Recommended cold tire inflation pressure for your vehicle’s tires is as follows,
Tire size P205/60R15 90H P205/55R16 89H P225/60R16 97H
Wheel size 15 x 6JJ 16 x 6 1/2JJ
Pressure Front 32 psi (220 kpa, 2.2 kg/cm 2
)3 0 p si
(210 kpa, 2.1 kg/cm 2
)
Rear 30psi (210 kpa, 2.1 kg/cm 2
)2 9 p si
(200 kpa, 2.0 kg/cm 2
)
Rear at trailer
towing –3
2 p si
(220 kpa, 2.2 kg/cm 2
)
Temporary
spare tire Size T135/70R16 T145/80R16
Pressure 60 psi (420 kpa, 4.2 kg/cm
2
)