wheel size SUBARU LEGACY 2004 4.G Owners Manual

7-29
Starting and operating
– CONTINUED –
4. Insert the screwdriver into the hole.
5. Push down on the screwdriver, push down the but-
ton and move the selector lever from the “P” to the “N”position.
6. Remove the screwdriver from the hole. Depress
the brake pedal and start the engine.
Take your vehicle to the nearest SUBARU dealer im-
mediately to have the system repaired. Rear viscous limited slip differential
(LSD) (if equipped)
y
Never start the engine while a tire on one side
is jacked up, as the vehicle may move. y If one rear tire is spinning in mud, avoid con-
tinued spinning at high speed as this could ad-
versely affect the LSD. y If a different size rear tire is temporarily used
(as in an emergency), it will adversely affect the
LSD. Always replace it with a regular size tire as
soon as possible.
The LSD provides optimum distribution of power ac-
cording to the difference in revolutions between the
right and left rear wheels that may be caused by cer-
tain driving conditions, thereby improving driving sta-
bility on snow-covered, muddy or other slippery roads.
UB7037BA

7-35
Starting and operating
– CONTINUED –
yWhenever suspension components, steering
components, or an axle are removed from a ve-
hicle equipped with VDC, have an authorized
SUBARU dealer perform an inspection of that
system.y The following precautions should be ob-
served in order to ensure that the VDC system
is operating properly:
– All four wheels should be fitted with tires of
the same size, type, and brand. Furthermore,
the amount of wear should be the same for allfour tires.
– Keep the tire pressure at the proper level as
shown on the placard attached to the vehi-
cle’s door pillar.
– Use only the special temporary spare tire to
replace a flat tire. With a temporary spare tire,
the effectiveness of the VDC system is re-
duced and this should be taken into account
when driving with vehicle.
In the event of wheelspin and/or skidding on a slippery
road surface and/or during cornering and/or an eva-
sive maneuver, the VDC system adjusts the engine’s
output and the wheels’ respective braking forces to
help maintain traction and directional control. y
Traction Control Function
The traction control function is designed to prevent
spinning of the driving wheels on slippery road surfac-
es, thereby helping to maintain traction and directional
control. Activation of this function is shown by steady
illumination of the VDC operation indicator light. y Skid Suppression Function
The skid suppression function is designed to help
maintain directional stability by suppressing the
wheels’ tendency to slide sideways during steering op-
erations. Activation of this function is shown by flash-
ing of the VDC operation indicator light.
NOTE y Slight twitching of the brake pedal may be felt
when the VDC-system operates; a small degree of
vehicle or steering wheel shaking may also be no-
ticed in this situation. These are normal character-
istics of VDC operation and are no cause for
alarm. y When driving off immediately after starting the
engine, a short-lived operation noise may be no-
ticed coming from the engine compartment. This
noise is generated as a result of a check being per-
formed on the VDC system and is normal.y Depending on the timing of activation of the
brakes, certain situations may occur just after

7-36
Starting and operating
driving off where the brake pedal seems to exhibit
a jolting motion. This too is a consequence of the
VDC operational check and is normal. y
In the circumstances listed below, the vehicle
may be more unstable than it feels to the driver.
The Vehicle Dynamics Control System may there-
fore operate. Such operation does not indicate a
system fault.
yon gravel-covered or rutted roads
y on unfinished roads
y when the vehicle is towing a trailer
y when the vehicle is fitted with snow tires or
winter tires
y Activation of the VDC system will cause opera-
tion of the steering wheel to feel slightly different
compared to that for normal conditions. y Even if the vehicle is equipped with a VDC sys-
tem, it is important that winter tires be used when
driving on snow-covered or icy roads. (All four
wheels should be fitted with tires of the same size
and brand). y It is always important to reduce speed when ap-
proaching a corner, even if the vehicle is equipped with VDC. y All four wheels should be fitted with tires of the
same size, type, and brand; furthermore, the
amount of wear should be the same for all four tires. If these precautions are not observed and
non-matching tires are used, it is quite possible
that the VDC system will be unable to operate cor-
rectly as intended. y
Always turn off the engine before replacing a
tire as failure to do so may render the VDC system
unable to operate correctly. „ VDC system monitor
T V D C O F F i n d i c a t o r l i g h t
y The VDC OFF indicator light turns on initially when
the ignition key is turned to the ON position; it subse-
quently turns off 6 seconds after the engine is started.
UB4010FA

8-7
Driving tips
– CONTINUED –
All wheel drive distributes the engine power to all four
wheels. AWD vehicles provide better traction when
driving on slippery, wet or snow-covered roads and
when moving out of mud, dirt and sand. By shifting
power between the front and rear wheels, SUBARU
AWD can also provide added traction during acceler-
ation, and added engine braking force during deceler-
ation.
Therefore, your SUBARU AWD vehicle may handle
differently than an ordinary two wheel drive vehicle
and it contains some features unique to AWD. For
safety purposes as well as to avoid damaging the
AWD system, you should keep the following tips in mind: y
An AWD vehicle is better able to climb steeper
roads under snowy or slippery conditions than a two
wheel drive vehicle. There is little difference in han-
dling, however, during extremely sharp turns or sud-
den braking. Therefore, when driving down a slope or
turning corners, be sure to reduce your speed and
maintain an ample distance from other vehicles. y When replacing a tire, make sure you use only the
same size, circumference, construction, brand, and
load range as the original tires listed on the tire plac-
ard. Using other sizes, circumferences or construction
may result in severe mechanical damage to the drive
train of your vehicle and may affect ride, handling,
braking, speedometer/odometer calibration, and
clearance between the body and tires. It also may be
dangerous and lead to loss of vehicle control. y If you use a temporary spare tire to replace a flat
tire, be sure to use the original temporary spare tire
stored in the vehicle. Using other sizes may result in
severe mechanical damage to the drive train of your
vehicle. y Always check the cold tire pressure before starting
to drive. The recommended tire pressure is provided
on the tire placard, which is located under the door
latch on the driver’s side. y Tire chains should always be placed on the front
wheels only.
HS8003BA

8-16
Driving tips
models
Driving on snowy grades or icy roads may require the
use of tire chains, in which case put the chains on the
front wheels only. Use only SAE class S type chains
that are of the correct size for your tires so as not to
damage the vehicle body or suspension.
When driving with tire chains, drive at speeds below
19 mph (30 km/h). When a temporary spare tire is on
a front wheel, replace the temporary spare tire with the
rear tire on the same side of the vehicle, and then fit
chains on the front tires.
Always use the utmost care when driving with tire
chains – overconfidence because you are driving with
tire chains could easily lead to a serious accident. „ Rocking the vehicle
If you must rock the vehicle to free it from snow, sand,
or mud, depress the accelerator pedal slightly and
move the selector lever back and forth between “D”
and “R” repeatedly. Do not race the engine. For the
best possible traction, avoid spinning the wheels when
trying to free the vehicle.
When the road surface is extremely slippery, you can
obtain better traction by starting the vehicle with the transmission in 2nd than 1st (both for MT and AT).
Refer to the “Automatic transmission” section in chap-
ter 7 for information on holding the transmission in 2nd position.

8-29
Driving tips
– CONTINUED –
tenance schedule under severe driving conditions” in
the “Warranty and Maintenance Booklet”.)
Under no circumstances should a trailer be towed with
a new vehicle or a vehicle with any new powertrain
component (engine, transmission, differential, wheel
bearings, etc.) for the first 1,000 miles (1,600 km) of
driving. „Maximum load limits
Never exceed the maximum load limits ex-
plained below. Exceeding the maximum load
limits could cause personal injury and/or vehi-
cle damage.
yAdequate size trailer brakes are required
when the trailer and its cargo exceed 1,000 lbs
(453 kg) total weight. y Before towing a trailer, check the trailer total
weight, GVW, GAWs and tongue load. Make
sure the load and its distribution in your vehicle
and trailer are acceptable.
T Total trailer weight
Total trailer weight
The total trailer weight (trailer weight plus its cargo
load) must never exceed the maximum weight shown
below.
HS8016AA

11 - 4 8
2Maintenance and service
ible, the tire is worn beyond the acceptable limit
and must be replaced immediately. With a tire
in this condition, driving at high speeds in wet
weather can cause the vehicle to hydroplane.
The resulting loss of vehicle control can lead to
an accident.
NOTE
For safety, inspect the tire tread regularly and re-
place the tires before their tread wear indicators
become visible. „
Tire rotation Tire wear varies from wheel to wheel. To maximize the
life of each tire and ensure that the tires wear uniform-
ly, it is best to rotate the tires every 7,500 miles
(12,500 km). Rotating the tires involves switching the
front and rear tires on the right-hand side of the vehicle
and similarly switching the front and rear tires on the
left-hand side of the vehicle. (Each tire must be kept
on its original side of the vehicle.)
Replace any damaged or unevenly worn tire at the
time of rotation. After tire rotation, adjust the tire pres-
sures and make sure the wheel nuts are correctly
tightened.
After driving approximately 600 miles (1,000 km),
check the wheel nuts again and retighten any nut that
has become loose. „
Tire replacement
The wheels and tires are important and integral parts
of your vehicle’s design; they cannot be changed arbi-
trarily. The tires fitted as standard equipment are opti-
mally matched to the characteristics of the vehicle and
were selected to give the best possible combination of
running performance, ride comfort, and service life. It
is essential for every tire to have a size and construc-
tion matching those shown on the tire placard and to
have a speed symbol and load index matching those
HSB056BA

11 -4 9
2Maintenance and service
– CONTINUED –
shown on the tire placard.
Using tires of a non-specified size detracts from con-
trollability, ride comfort, braking performance, speed-
ometer accuracy and odometer accuracy. It also cre-
ates incorrect body-to-tire clearances and inappropri-
ately changes the vehicle’s ground clearance.
All four tires must be the same in terms of manufactur-
er, brand (tread pattern), construction, and size. You
are advised to replace the tires with new ones that are
identical to those fitted as standard equipment.
For safe vehicle operation, SUBARU recommends re-
placing all four tires at the same time.
yAll four tires must be the same in terms of
manufacturer, brand (tread pattern), construc-
tion, degree of wear, speed symbol, load index
and size. Mixing tires of different types, sizes or
degrees of wear can result in damage to the ve-
hicle’s power train. Use of different types or siz-
es of tires can also dangerously reduce control-
lability and braking performance and can lead
to an accident. y Use only radial tires. Do not use radial tires
together with belted bias tires and/or bias-ply tires. Doing so can dangerously reduce control-
lability, resulting in an accident.
„ Wheel replacement
When replacing wheels due, for example, to damage,
make sure the replacement wheels match the specifi-
cations of the wheels that are fitted as standard equip-
ment. Replacement wheels are available from
SUBARU dealers.
Use only those wheels that are specified for
your vehicle. Wheels not meeting specifica-
tions could interfere with brake caliper opera-
tion and may cause the tires to rub against the
wheel well housing during turns. The resulting
loss of vehicle control could lead to an acci-
dent.

12-5
Specifications
– CONTINUED –
„Tires
„ Wheel alignment
Tire sizeP205/60R15 90HP205/55R16 89HP225/60R16 97H
Wheel size15 x 6JJ16 x 6 1
/2 JJ
PressureFront32 psi (220 kPa, 2.2 kg/cm 2
)30 psi (210 kPa, 2.1 kg/cm 2
)
Rear30 psi (210 kPa, 2.1 kg/cm 2
)29 psi (200 kPa, 2.0 kg/cm 2
)
Rear at trailer
towing–32 psi (220 kPa, 2.2 kg/cm 2
)
Temporary
spare tireSizeT135/70R16T145/80R16
Pressure60 psi (420 kPa, 4.2 kg/cm 2
)
ItemLegacyOUTBACK
SedanWagonSedanWagon
ToeFront0 in (0 mm)
Rear0 in (0 mm)
CamberFront–0 °05’0 °20’
Rear–0 °30’–0 °20’–0 °10’

13-5
Consumer information and Reporting safety defects
– CONTINUED –
„Recommended tire inflation pressure
T Recommended cold tire inflation pressure
Recommended cold tire inflation pressure for your vehicle’s tires is as follows,
Tire size P205/60R15 90H P205/55R16 89H P225/60R16 97H
Wheel size 15 x 6JJ 16 x 6 1/2JJ
Pressure Front 32 psi (220 kpa, 2.2 kg/cm 2
)3 0 p si
(210 kpa, 2.1 kg/cm 2
)
Rear 30psi (210 kpa, 2.1 kg/cm 2
)2 9 p si
(200 kpa, 2.0 kg/cm 2
)
Rear at trailer
towing –3
2 p si
(220 kpa, 2.2 kg/cm 2
)
Temporary
spare tire Size T135/70R16 T145/80R16
Pressure 60 psi (420 kpa, 4.2 kg/cm
2
)