towing SUBARU LEGACY 2005 4.G Owner's Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2005, Model line: LEGACY, Model: SUBARU LEGACY 2005 4.GPages: 627, PDF Size: 6.42 MB
Page 476 of 627
9-21
In case of emergency
– CONTINUED –
Confirm that the cooling fan is turning. If the fan is not
turning, immediately turn the engine off and contact
your authorized dealer for repair.
3. After the engine coolant temperature has dropped, turn off the engine.
If the temperature gauge stays at the overheated
zone, turn the engine off.
4. After the engine has fully cooled down, check the
coolant level in the reserve tank.
If the coolant level is below the “MIN” mark, add cool-
ant up to the “MAX” mark.
5. If there is no coolant in the reserve tank, add cool-
ant to the reserve tank. Then remove the radiator cap
and fill the radiator with coolant.
If you remove the radiator cap from a hot radiator, first
wrap a thick cloth around the radiator cap, then turn
the cap counterclockwise slowly without pressing
down until it stops. Release the pressure from the ra-
diator. After the pressure has been fully released, re-
move the cap by pressing down and turning it.Towing
Never tow AWD vehicles (both AT and MT) with
the front wheels raised off the ground while the
rear wheels are on the ground, or with the rear
wheels raised off the ground while the front
wheels are on the ground. This will cause the
vehicle to spin away due to the operation or de-
terioration of the center differential.
If towing is necessary, it is best done by your SUBARU
UG9013BA
Page 477 of 627
9-22
In case of emergency
dealer or a commercial towing service. Observe the
following procedures for safety. !
Towing and tie-down hooks
The towing hooks should be used only in an emergen-
cy (e.g., to free a stuck vehicle from mud, sand or
snow).
" Use only the specified towing hooks and tie-
down hooks. Never use suspension parts or
other body parts for towing or tie-down purpos-
es. " Never use the tie-down hook closest to the
muffler under the vehicle for towing purposes. " To prevent deformation to the bumper and
the towing hook, do not apply excessive lateral
load to the towing hooks.
Front towing hook (OUTBACK models):
1. Take out the towing hook, screwdriver and wheel
nut wrench from the on board tool bucket. 2. Wrap a flat-head screwdriver in a vinyl tape or
cloth, insert it into the gap between the cover and the
front bumper, and use it to lever the cover open.
3. Pull the entire fog light cover toward you.
UB9214BA
Page 478 of 627
9-23
In case of emergency
– CONTINUED –
4. Screw the towing hook into the thread hole until the
threads can no longer be seen. 5. Tighten the towing hook securely by a wheel nut
wrench.
After towing, remove the towing hook from the vehicle
and stow it in the tool bag.
Fit the towing hook cover on the bumper.
Front towing hook (except OUTBACK models):
1. Take out the towing hook, screwdriver and wheel
nut wrench from the on board tool bag.
UB9215BAUB9216BA
Page 479 of 627
9-24
In case of emergency
2. Wrap a flat-head screwdriver with cloth or vinyl.
Then, insert the screwdriver into the gap between the
fog light cover and the bumper, and pry out the cover.
3. Pull the entire fog light cover toward you.
4. Likewise, insert the screwdriver still wrapped with
cloth or vinyl into the cutout between the towing hook
cover and the bumper. Pry out the cover.
UB9204BAUB9205BA
Page 480 of 627
9-25
In case of emergency
– CONTINUED –
5. Screw the towing hook into the thread hole until the
threads can no longer be seen. 6. Tighten the towing hook securely by a wheel nut
wrench.
After towing, remove the towing hook from the vehicle
and stow it in the tool bag.
Fit the fog light cover and towing hook cover on the
bumper.
"
Do not use the towing hook except when tow-
ing your vehicle. " Be sure to remove the towing hook after tow-
ing. Leaving the towing hook mounted on the
vehicle could interfere with proper operation of
UB9206BAUB9207BA
Page 481 of 627
9-26
In case of emergency
the SRS airbag system in a frontal collision.
Rear towing hook:
The rear towing hook is located below the center of the
rear bumper.
Never use the rear towing hook to tie the vehi-
cle down. Front tie-down hooks:
The front tie-down hooks are located between each of
the front tires and the front bumper.
UB9509BA
UB9202BA
Page 483 of 627
9-28
In case of emergency
!
Towing with all wheels on the ground
"Never turn the ignition switch to the “LOCK”
position while the vehicle is being towed be-
cause the steering wheel and the direction of
the wheels will be locked." Remember that the brake booster and power
steering do not function when the engine is not
running. Because the engine is turned off, it will
take greater effort to operate the brake pedal
and steering wheel.
" If transmission failure occurs, transport your
vehicle on a flat-bed truck. " Do not run the engine while being towed us-
ing this method. Transmission damage could
result if the vehicle is towed with the engine
running. " For vehicles with automatic transmission,
the traveling speed must be limited to less than
20 mph (30 km/h) and the traveling distance to
less than 31 miles (50 km). For greater speeds
and distances, transport your vehicle on a flat-
bed truck.
1. Check the transmission and differential oil levels
and add oil to bring it to the upper level if necessary.
2. Release the parking brake and put the transmis-
sion in neutral.
3. The ignition switch should be in the “ACC” position
while the vehicle is being towed.
4. Take up slack in the towline slowly to prevent dam-
age to the vehicle.UB9219BA
Page 490 of 627
9-35
In case of emergency
– CONTINUED –
Station wagon: Open the center lid, remove the left
hand part of the lid, and take out the jack handle.
For how to use the jack, refer to “Flat tires”. !
Other maintenance tools
In addition to a jack and a jack handle, the tool bucket
on your vehicle contains the following maintenance
tools.
Screwdriver
Towing hook
Wheel nut wrench
Hex-headed wrench (only for vehicles with moon- roof)
UB9504BA
UB9217BA
Page 516 of 627
11 -1 7
Maintenance and service
– CONTINUED –
API Service label
A) Indicates the oil quality by API designations
B) Indicates the SAE oil viscosity grade
C) Indicates that the oil has fuel saving capabilities
In choosing an oil, you want the proper quality and vis-
cosity, as well as one that will add to fuel economy.
The following table lists the recommended viscosities
and applicable temperatures.
When adding oil, different brands may be used togeth-
er as long as they are the same API classification and
SAE viscosity as those recommended by SUBARU. SAE viscosity number and applicable temperature
*: 5W-30 is preferred.
Engine oil viscosity (thickness) affects fuel economy.
Oils of lower viscosity provide better fuel economy.
However, in hot weather, oil of higher viscosity is re-
quired to properly lubricate the engine. ! Recommended grade and viscosity
under severe driving conditions
If the vehicle is used in desert areas, in areas with very
high temperatures, or used for heavy-duty applica-
tions such as towing a trailer, use of oil with the follow-
ing grade and viscosities is recommended.
APISERVICESL
ENERGYCONSERVING
SAE
5W-30
A
B
C
HSB022BC
5W-30*10W-30, 10W-40
-30 -20 -10 0 10 20 30 40
-20
06 0
20 80 100 40
HSB024BA
Page 590 of 627
12-5
Specifications
– CONTINUED –
!Tires
! Wheel alignment
Tire sizeP205/55R16 89H215/45ZR17P225/60R16 97HP225/55R17 95V
Wheel size16 x 6.5JJ17 x 7JJ16 x 6.5JJ17 x 7JJ
PressureFront32 psi
(220 kPa, 2.2 kgf/cm 2
)35 psi
(240 kPa, 2.4 kgf/cm 2
)32 psi (220 kPa, 2.2 kgf/cm 2
)
Rear30 psi
(210 kPa, 2.1 kgf/cm 2
)33 psi
(230 kPa, 2.3 kgf/cm 2
)30 psi (210 kPa, 2.1 kgf/cm 2
)
Rear at trailer
towing–32 psi (220 kPa, 2.2 kgf/cm 2
)
Temporary
spare tireSizeT135/80R16T135/70D17T155/70D17
Pressure60 psi (420 kPa, 4.2 kgf/cm 2
)
ItemLegacyOUTBACK
SedanStation wagonSedanStation wagon
ToeFront0 in (0 mm)
Rear0 in (0 mm)
CamberFront–0 °15’0 °40’
Rear–0 °40’–0 °30’–0 °10’