engine oil SUBARU OUTBACK 2000 3.G User Guide

11-4
Always use the proper tools and make certain that they are
well maintained. Never get under the vehicle supported only by a jack. Always
use a safety stands to support the vehicle. Never keep the engine running in a poorly ventilated area,
such as a garage or other closed areas. Do not smoke or allow open flames around the fuel or battery.
This will cause a fire. Because the fuel system is under pressure, replacement of the
fuel filter should be performed only by your SUBARU dealer. Wear adequate eye protection to guard against getting oil or
fluids in your eyes. If something does get in your eyes, thorough-
ly wash it out with clean water. Do not tamper with the wiring of the SRS airbag system or
seatbelt pretensioner system, or attempt to take its connectorsapart, as that may activate the system or it can render it inopera-tive. The wiring and connectors of these systems are yellow for
easy identification. NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt pretensioner needs service, con-
sult your nearest SUBARU dealer. Before checking or servicing in the engine compart- ment
Always stop the engine and set the parking brake firmly to pre-
vent the vehicle from moving. Always let the engine cool down. Engine parts become very
hot when the engine is running and remain hot for some time af-ter the engine is stopped. Do not spill engine oil, engine coolant, brake fluid or any other
fluid on hot engine components. This may cause a fire. Always remove the key from the ignition switch. When the
ignition switch is in the “ON” position, the cooling fan may oper-
ate suddenly even when the engine is stopped.

Maintenance and service11-7
–
CONTINUED –
Engine compartment overview
HBB036BB
1 Manual transmission oil level
g aug e (MT) (p ag e 11-20) or
Differential g ear oil level g aug e
(AT) (p ag e 11-23)
2 Air c leaner element
(p ag e 11-17)
3 Clutc h fluid reservoir
(p ag e 11-29)
4 Automatic transmission fluid
level g aug e (p ag e 11-21)
5 Brake fluid reservoir
(p ag e 11-27)
6 Fuel filter 7
Wind shield washer tank
(p ag e 11-39)
8 Fuse b ox (p ag e 11-43)
9 Battery (p ag e 11-42)
Q Eng ine oil filler c ap
(p ag e 11-8)
W Eng ine c oolant reservoir
(p ag e 11-14)
E Rad iator c ap (p ag e 11-14)
R Eng ine oil level g aug e
(p ag e 11-8)
T Power steering fluid reservoir
(p ag e 11-26)

11-8Engine oil
Checking the oil level
Chec k the eng ine oil level at eac h fuel stop .
OM-H0189HBB004BA
1. Park the vehic le on a level surfac e and stop the eng ine.
2. Pull out the d ip stic k, wip e it c lean, and insert it ag ain.
3. Be sure the d ip stic k is c orrec tly inserted until it stop s with the
g rap hic symb ol
on its top ap p earing as shown in the illustra-
tion.
4. Pull out the d ip stic k ag ain and c hec k the oil lev el on it. If it is b elow
the lower level, ad d oil to b ring the level up to t he up p er level.
CAUTION
Use only engine oil with the recommended grade and viscosity.
If you c hec k the oil level just after stop p ing the eng ine, wait a few min-
utes for the oil to d rain b ac k into the oil p an b ef ore c hec king the level.
Just after d riving or while the eng ine is warm, the eng ine oil level
read ing may b e in a rang e b etween the up p er level a nd the notc h
mark. This is c aused b y thermal exp ansion of the en g ine oil.
To p revent overfilling the eng ine oil, d o not ad d a ny ad d itional oil
ab ove the up p er level when the eng ine is c old .

Maintenance and service11-9
–
CONTINUED –

Changing the oil and oil filter
Chang e the oil and oil filter ac c ord ing to the main tenanc e sc hed ule in
the “Warranty and Maintenanc e Booklet ”.
The eng ine oil and oil filter must b e c hang ed more freq uently than
listed in the maintenanc e sc hed ule when d riving on d usty road s,
when short trip s are freq uently mad e, or when d rivi ng in extremely
c old whether.
1. Warm up the eng ine b y letting the eng ine id le for ab out 10 minutes
to ease d raining the eng ine oil.
2. Park the vehic le on a level surfac e and stop the eng ine.
3. Remove the oil filler c ap .
HBB005BB
4. Drain out the eng ine oil b y removing the d rain p l ug while the en-
g ine is still warm. The used oil should b e d rained into an ap p rop riate
c ontainer and d isp osed of p rop erly.
WARNING
Be careful not to burn yourself with hot engine oil.
5. Wip e the seating surfac e of the d rain p lug with a c lean c loth and
tig hten it sec urely with a new sealing washer after the oil has c om-
p letely d rained out.

Maintenance and service11-11
–
CONTINUED –
12. Reinstall the c over und er the oil filter.
13. Pour the sp ec ified amount of eng ine oil throug h
the filler nec k.
Oil c ap ac ity: 4.2 US q t (4.0 liters, 3.5 Imp q t)
14. Start the eng ine and make sure that no oil leak s ap p ear around
the filter ’s rub b er seal.
15. Run the eng ine until it reac hes the normal op er ating temp erature.
Then stop the eng ine and wait a few minutes to allo w the oil d rain
b ac k. Chec k the oil level ag ain and if nec essary, a d d more eng ine oil.
Recommended grade and viscosity CAUTION
Use only engine oil with the recommended grade and viscosity.
Oil grade: API classification SJ or SH with the words “ENERGY
CONSERVING II ” (if you cannot obtain the oil with SJ
or SH grade, you may use SG grade oil.) or the new API certification mark (Starburst mark) dis-
played on the container.
New API Certification Mark (Starburst Mark)API Service label
1
2
3
1 Ind ic ates the oil q uality b y API d esig nations
2 Ind ic ates the SAE oil visc osity g rad e
3 Ind ic ates that the oil has fuel saving c ap ab ilities

Maintenance and service11-13
–
CONTINUED –
Cooling system
WARNING
Never attempt to remove the radiator cap until the engine has
been shut off and has cooled down completely. Since the coolantis under pressure, you may suffer serious burns from a spray ofboiling hot coolant when the cap is removed.
CAUTION
The cooling system has been filled at the factory with a high
quality, corrosion-inhibiting, year-around coolant which providesprotection against freezing down to –33F ( –36 C). For adding,
use genuine SUBARU coolant or an equivalent: a mixture of 50%
soft water and 50% ethylene-glycol basis coolant. Use of improp-er coolants may result in corrosion in the cooling system. It is im-portant to maintain protection against freezing and corrosion,
even if freezing temperatures are not expected. Never mix differ-ent kinds of coolant. Do not splash the engine coolant over painted parts. The alco-
hol contained in the engine coolant may damage the paint sur-face.
Hose and connections
Your vehic le emp loys an elec tric c ooling fan whic h is thermostatic ally
c ontrolled to op erate when the eng ine c oolant reac h es a sp ec ific tem-
p erature.
If the rad iator c ooling fan d oes not op erate even w hen the eng ine
c oolant temp erature g aug e exc eed s the normal op erat ing rang e, the
c ooling fan c irc uit may b e d efec tive. Chec k the fus e and rep lac e it if
nec essary. If the fuse is not b lown, have the c ooli ng system c hec ked
b y your SUBARU d ealer.
If freq uent ad d ition of c oolant is nec essary, there may b e a leak in the
eng ine c ooling system. It is rec ommend ed that the c ooling system
and c onnec tions b e c hec ked for leaks, d amag e, or lo oseness.

Maintenance and service11-15
–
CONTINUED –

Changing the coolant
WARNING
Never attempt to remove the radiator cap until the engine has
been shut off and has cooled down completely. Since the coolantis under pressure, you may suffer serious burns from a spray ofboiling hot coolant when the cap is removed.
Chang e the eng ine c oolant using the following p roc e d ures ac c ord ing
to the maintenanc e sc hed ule in the “Warranty and Maintenanc e Book-
let ”.
1. Remove the und er c over.
2. Plac e a p rop er c ontainer und er the d rain p lug and loosen the d rain
p lug .
HBB006BB
3. Loosen the rad iator c ap to d rain the c oolant from the rad iator. Then
d rain the c oolant from the reserve tank. Tig hten th e d rain p lug sec ure-
ly.

Specifications12-3
–
CONTINUED –
OUTBACK station wagon
Overall leng th 187.4 in (4,760 mm)
Overall wid th 68.7 in (1,745 mm)
Overall heig ht 62.2 in (1,580 mm)
Ground c learanc e 7.3 in (185 mm)
Front tread 57.9 in (1,470 mm)
Rear tread 57.7 in (1,465 mm)
Wheelb ase 104.3 in (2,650 mm)
Engine 2.5 liter
Eng ine mod el EJ251
Eng ine typ e Horizontally op p osed , liq uid c ooled
4 c ylind er, 4 stroke g asoline eng ine
Eng ine d isp lac ement 2,457 c c (149.9 c u in.)
Bore 3.92 in (99.5 mm)
Stroke 3.11 in (79.0 mm)
Comp ression ratio 10.0 : 1
Firing ord er 1 - 3 - 2 - 4
Electrical system
Battery typ e and c ap ac ity
MT: 55D23L
AT: 75D23L
Alternator 12V-90A
Sp ark p lug s typ e RC10YC4 (Champion) RC8YC4 (Champ ion)
BKR6E-11 (NGK)
K20PR-U11 (NIPPONDENSO)
Capacities
Fuel tank 16.9 US g al (64 liters, 14.1 Imp g al)
Eng ine oil 4.2 US q t (4.0 liters, 3.5 Imp q t)
Transmission oil (MT) 3.7 US q t (3.5 liters, 3.1 Imp q t)
Transmission fluid (AT) 9.8 US q t (9.3 liters, 8.2 I mp q t)