oil SUBARU OUTBACK 2000 3.G User Guide

Instruments and controls3-13
–
CONTINUED –
the p rop er level b ut the lig ht remains on, c ontac t
your nearest SUBARU
d ealer immed iately. AT OIL TEMPerature warning light
(for AT vehicles)
If this lig ht c omes on when the eng ine is running , it may ind ic ate that the
automatic transmission fluid temp erature is too hot .
If the lig ht c omes on while d riving , it is unnec ess ary to stop the vehic le,
b ut avoid d riving up steep g rad es or in stop and g o traffic .
Automatic transmission control system warning
If the lig ht flashes after the eng ine starts, it ma y ind ic ate that the auto-
matic transmission c ontrol system is not working p r op erly. Contac t
your nearest SUBARU d ealer for servic e immed iately.
ABS warning light
The ABS warning lig ht c omes on when the ig nition sw itc h is turned to the
“ ON ” p osition and g oes out after ab out two sec ond s.
This is an ind ic ation that the ABS system is workin g p rop erly.
If the warning lig ht b ehaves as follows, the ABS sy stem may not work
p rop erly. The warning lig ht d oes not c ome on when the ig nitio n switc h is turned
to the “ON ” p osition.
The warning lig ht c omes on when the ig nition switc h is turned to the
“ ON ” p osition, b ut it d oes not g o out even when the veh ic le sp eed
exc eed s ap p roximately 8 mp h (12 km/h). The warning lig ht c omes on d uring d riving .
When the warning lig ht is on, the ABS func tion shut s d own; however, the
c onventional b rake system c ontinues to op erate norm ally. If this oc c urs,
have the ABS system rep aired at the first availab le op p ortunity b y your
SUBARU d ealer.
(U.S.) (Canada)

Climate control4-11
–
CONTINUED –
2. Set the air outlet c ontrol d ial to the
“ ” p osition.
3. Set the air c ond itioner b utton to the “ON ” p osition.
4. Set the temp erature c ontrol d ial to the red area.
5. Set the fan sp eed c ontrol d ial at the hig hest sp e ed .
Operating tips for heater and air conditioner Cleaning ventilator grille
HB5019BC
Always keep the front ventilator inlet g rille free of snow, leaves, or oth-
er ob struc tions to ensure effic ient heating and d ef rosting . Sinc e the
c ond enser is loc ated in front of the rad iator, this area should b e kep t
c lean b ec ause c ooling p erformanc e is imp aired b y an y ac c umulation
of insec ts and leaves on the c ond enser. Efficient cooling after parking in direct sunlight
After p arking in d irec t sunlig ht, d rive with the wi nd ows op en for a few
minutes to allow outsid e air to c irc ulate into the heated interior. This
results in q uic ker c ooling b y the air c ond itioner. Keep the wind ows
c losed d uring the op eration of the air c ond itioner for maximum c ool-
ing effic ienc y. Lubrication oil circulation in the refrigerant circuit
Op erate the air c ond itioner c omp ressor at a low eng ine sp eed (at id le
or low d riving sp eed s) a few minutes eac h month d ur ing the off-sea-
son to c irc ulate its oil.

Interior equipment6-13
–
CONTINUED –

Front ashtray
To op en the ashtray, p ull the lid out. Rear ashtray
The rear ashtray is loc ated on the up p er sid e of th e b ac k of the c enter
c onsole. To op en the ashtray, p ull the up p er ed g e o f the lid .
To remove the ashtray for c leaning , op en it and p ul l it out while p ushing
the inner p late d own.
Accessory power socket
In the luggage compartment (if equipped) and on the center
console (if equipped) CAUTION
Do not attempt to use a cigarette lighter in the accessory
power socket. Do not place any foreign objects, especially metal ones such
as coins or aluminum foil, into the accessory power socket. Thatcould cause a short circuit. Always put the cap on the accessorypower socket when they are not in use. Use only electrical appliances which are designed for 12V DC
and which consume less than 120W. Overloading the accessorypower socket can cause a short circuit. Do not use double adapt-ers or more than one electrical appliance. If the plug on your electric appliance is either too loose or too
tight for the accessory power socket, this can result in a poorcontact or cause the plug to get stuck. Only use plugs that fit
properly. Use of an electric appliance in the accessory power socket for
a long period of time while the engine is not running can causebattery discharge. Before driving your vehicle, make sure that the plug and the
cord on your electrical appliance will not interfere with your shift-ing gears and operating the accelerator and brake pedals. If theydo, do not use the electrical appliance while driving.

7-8
7. Fasten your seatb elt. Chec k that your p asseng ers
have fastened their
seatb elts.
8. Chec k the op eration of the warning and ind ic ator lig hts when the ig ni-
tion switc h is turned to the “ON ” p osition.
9. Chec k the g aug es, ind ic ator and warning lig hts af ter starting the en-
g ine. NOTE Engine oil, engine coolant, brake fluid, washer fluid and other fluid
levels should be checked daily, weekly or at fuel stops.
Starting the engine
CAUTION
Do not operate the starter motor continuously for more than ten
seconds. If the engine fails to start after operating the starter forfive to ten seconds, wait for ten seconds or more before tryingagain.
Starting the engine for a manual transmission vehicle
1. Ap p ly the p arking b rake.
2. Turn off unnec essary lig hts and ac c essories.
3. Press the c lutc h p ed al to the floor and shift the shift lever into neutral.
Hold the c lutc h p ed al to the floor while starting t he eng ine. The starter
motor will only op erate when the c lutc h p ed al is p r essed fully to the floor.
4. Turn the ig nition switc h to the “ON ” p osition and c hec k the op eration
of the warning and ind ic ator lig hts. Refer to the “Warning and ind ic ator
lig ht ” sec tion (c hap ter 3).
5. Turn the ig nition switc h to the “START ” p osition without d ep ressing
the ac c elerator p ed al. Release the key immed iately after the eng ine has
started .
If the eng ine d oes not start within ten sec ond s, wa it a while and then turn
the ig nition switc h to the “START ” p osition ag ain while d ep ressing the ac -
c elerator p ed al half way d own.

8-10trac tion b y starting the vehic le with the transmiss
ion in 2nd than 1st
(b oth for MT and AT). Never eq uip your vehic le with tires larg er than tho se sp ec ified in
this manual. Freq uent d riving of an AWD vehic le und er hard -d rivi ng c ond itions
suc h as roug h road s or off road s will nec essitate m ore freq uent re-
p lac ement of eng ine oil, b rake fluid and transmissi on oil than that sp e-
c ified in the maintenanc e sc hed ule d esc rib ed in the “Warranty and
Maintenanc e Booklet ”.
Rememb er that d amag e d one to your Sub aru while op er ating it off-
road and not using c ommon sense p rec autions suc h as those listed
ab ove is not elig ib le for warranty c overag e.
Winter driving
HB3010AA
Operation during cold weather
Carry some emerg enc y eq uip ment, suc h as tire c hains , a wind ow
sc rap er, a b ag of sand , flares, a small shovel, and jump er c ab les.
Chec k the b attery and c ab les. Cold temp eratures red uc e b attery c a-
p ac ity. The b attery must b e in g ood c ond ition to p r ovid e enoug h p ow-
er for c old winter starts.
Use an eng ine oil of p rop er g rad e and visc osity for c old weather.
Heavy summer oil will c ause hard er starting .

Driving tips8-37
–
CONTINUED –
nearest SUBARU d ealer. n
Driving on grades
Before g oing d own a steep hill, slow d own and shift into lower g ear
(if nec essary, use 1st g ear) in ord er to utilize th e eng ine b raking effec t
and p revent overheating of your vehic le ’s b rakes. Do not make sud -
d en d ownshifts. When d riving up hill in hot weather, the air c ond iti oner may turn off
automatic ally to p rotec t the eng ine from overheatin g .
When d riving up hill in hot weather, p ay attention t o the water tem-
p erature g aug e p ointer (for all vehic les) and AT OI L TEMP warning
lig ht (for AT vehic les) sinc e the eng ine and transm ission are relatively
p rone to overheating und er these c ond itions. If the water temp erature
g aug e p ointer ap p roac hes the OVERHEAT zone or the A T OIL TEMP
warning lig ht illuminates, immed iately switc h off t he air c ond itioner
and stop the vehic le at the nearest safe p lac e. Ref er to the “Eng ine
overheat ” sec tion in c hap ter 9, and “Warning and ind ic ator lig hts ”
sec tion in c hap ter 3. If your vehic le has a automatic transmission, avoid using the ac c el-
erator p ed al to stay stationary on an up hill slop e instead of using the
p arking b rake or foot b rake. That may c ause the tra nsmission fluid to
overheat. Also, if your vehic le is eq uip p ed with an automatic transmis-
sion, avoid d riving with the g ear selec tor lever in “ D ” when towing a
heavy trailer to p revent fluid overheating . n Parking on a grade
Always b loc k the wheels und er b oth vehic le and trai ler when p arking .
Ap p ly the p arking b rake firmly. You should not p ark on a hill or slop e.
But if p arking on a hill or slop e c annot b e avoid ed , you should take
the following step s:
1. Ap p ly the b rakes and hold the p ed al d own.
2. Have someone p lac e wheel b loc ks und er b oth the ve hic le and
trailer wheels.
3. When the wheel b loc ks are in p lac e, release the r eg ular b rakes
slowly until the b loc ks ab sorb the load .
4. Ap p ly the reg ular b rakes and then ap p ly the p arki ng b rake; slowly
release the reg ular b rakes.

9-4
HB8003BB
HG0106
Indicator location mark
Tread wear indicator bar
NOTE
(If your vehicle is AWD with automatic transmission) Before driving your vehicle with the temporary spare tire, put a spare fuse insidethe FWD connector located in the engine compartment and confirm
that the Front-wheel drive warning light comes on. The all wheeldrive capability of the vehicle has now been deactivated. After re-
installing the conventional tire, remove the spare fuse from the FWDconnector in order to reactivate all wheel drive.
Flat tires
WARNING
Do not jack up the vehicle on an incline or a loose road sur-
face. The jack can come out of the jacking point or sink into the ground and this can result in a severe accident. Use only the jack provided with your vehicle. The jack sup-
plied with the vehicle is designed only for changing a tire. Neverget under the vehicle while supporting the vehicle with this jack. Always turn the engine off before raising the flat tire off the
ground using the jack. Never swing or push the vehicle sup-ported with the jack. The jack can come out of the jacking pointdue to a jolt and this can result in a severe accident. Do not use oil or grease on the wheel studs or nuts when the

In case of emergency9-13
–
CONTINUED –
4
Connec t the other end of the c ab le to the eng ine li fting b rac ket.
Make sure that the c ab les are not near any moving p arts and that
the c ab le c lamp s are not in c ontac t with any other metal.
5. Start the eng ine of the vehic le with the b ooster b attery and run it at
mod erate sp eed . Then start the eng ine of the vehic l e that has the d is-
c harg ed b attery.
6. When finished , c arefully d isc onnec t the c ab les in exac tly the re-
verse ord er.
Engine overheating
WARNING
Never attempt to remove the radiator cap until the engine hasbeen shut off and has fully cooled down. When the engine is hot,the coolant is under pressure. Removing the cap while the engineis still hot could release a spray of boiling hot coolant, which
could burn you very seriously.
If the eng ine overheats, safely p ull off the road a nd stop the vehic le in a
safe p lac e.
If steam is coming from the engine compartment
Turn the eng ine off and g et everyone away from the vehic le until it
c ools d own. If no steam is coming from the engine compartment
1. Keep the eng ine running at id ling sp eed .
2. Op en the hood to ventilate the eng ine c omp artment .
Confirm that the c ooling fan is turning . If the fan is not turning , im-
med iately turn the eng ine off and c ontac t your auth orized d ealer for
rep air.
3. After the eng ine c oolant temp erature has d rop p ed , turn off the en-
g ine.
If the temp erature g aug e stays at the overheated zo ne, turn the en-
g ine off.

In case of emergency9-23
–
CONTINUED –

Towing with all wheels on the ground
WARNING
Never turn the ignition switch to the “LOCK” position while the
vehicle is being towed because the steering wheel and the direc- tion of the wheels will be locked. Remember that the brake booster and power steering do not
function when the engine is not running. Because the engine isturned off, it will take greater effort to operate the brake pedal andsteering wheel.
CAUTION
If transmission failure occurs, transport your vehicle on a flat-
bed truck. For vehicles with automatic transmission, the traveling speed
must be limited to less than 20 mph (30 km/h) and the traveling
distance to less than 31 miles (50 km). For greater speeds and
distances, transport your vehicle on a flat-bed truck.
HB8010AA
1. Chec k the transmission and d ifferential oil level s and ad d oil to
b ring it to the up p er level if nec essary.
2. Release the p arking b rake and p ut the transmissio n in neutral.
3. The ig nition switc h should b e in the “ACC ” p osition while the ve-
hic le is b eing towed .

10-2Exterior care
Washing
CAUTION
When washing the vehicle, the brakes may get wet. As a result,
the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brakepedal to heat up the brakes. Do not wash the engine compartment and areas adjacent to it.
If water enters the engine air intake, electrical parts or the power
steering fluid reservoir, it will cause engine trouble or faulty
power steering respectively.
The b est way to p reserve your vehic le ’s b eauty is freq uent washing .
Wash the vehic le at least onc e a month to avoid c on tamination b y road
g rime.
Wash d irt off with a wet sp ong e and p lenty of lukew arm or c old water. Do
not wash the vehic le with hot water and in d irec t s unlig ht.
Salt, c hemic als, insec ts, tar, soot and b ird d rop p i ng s should b e washed
off b y using a lig ht d eterg ent, as req uired . If you use a lig ht d eterg ent,
make c ertain that it is a neutral d eterg ent. Do not use strong soap or
c hemic al d eterg ents. All c leaning ag ents should b e p romp tly flushed
from the surfac e and not allowed to d ry there. Rins e the vehic le thor-
oug hly with p lenty of lukewarm water. Wip e the rema ining water off with a
c hamois or soft c loth. NOTE When having your vehicle washed in an automatic car wash, make
sure beforehand that the car wash is of suitable type. If the vehicle
is equipped with a rear/roof spoiler, it may be damaged by car washbrushes or other equipment.