flat tire SUBARU OUTBACK 2002 3.G User Guide

In case of emergency9-3
–
CONTINUED –
Temporary spare tire
WARNING
Never tow a trailer when the temporary spare tire is used. The temporary spare tire is not designed to sustain the towing load.
Use of the temporary spare tire when towing can result in failureof the spare tire and/or less stability of the vehicle and may leadto an accident.
CAUTION
Never use any temporary spare tire other than the original. Usingother sizes may result in severe mechanical damage to the drivetrain of your vehicle.
The temporary spare tire is smaller and lighter than a conventional tire
and is designed for emergency use only. Remove the temporary spare
tire and re-install the conventional tire as soon as possible because the
spare tire is designed only for temporary use.
Check the inflation pressure of the temporary spare tire periodically to
keep the tire ready for use. The correct pressure is 60 psi (420 kPa, 4.2
kg/cm 2
).
When using the temporary spare tire, note the following: Do not exceed 50 mph (80 km/h).
Do not put a tire chain on the temporary spare tire. Because of the
smaller tire size, a tire chain will not fit properly. Do not use two or more temporary spare tires at the same time.
Do not drive over obstacles. This tire has a smaller diameter, so
road clearance is reduced. When the wear indicator appears on the tread, replace the tire.

9-4
HB8003BB
HG0106
Indicator location mark
Tread wear indicator bar
NOTE
[Automatic transmission vehicle not equipped with VDC (Vehicle Dy-
namics Control)] Before driving your vehicle with the temporaryspare tire, put a spare fuse inside the FWD connector located in theengine compartment and confirm that the Front-wheel drive warninglight comes on. The all wheel drive capability of the vehicle has now
been deactivated. After re-installing the conventional tire, removethe spare fuse from the FWD connector in order to reactivate allwheel drive.
Flat tires
WARNING
Do not jack up the vehicle on an incline or a loose road sur-
face. The jack can come out of the jacking point or sink into the ground and this can result in a severe accident. Use only the jack provided with your vehicle. The jack sup-
plied with the vehicle is designed only for changing a tire. Neverget under the vehicle while supporting the vehicle with this jack. Always turn the engine off before raising the flat tire off the
ground using the jack. Never swing or push the vehicle sup-ported with the jack. The jack can come out of the jacking pointdue to a jolt and this can result in a severe accident.

In case of emergency9-5
–
CONTINUED –
Do not use oil or grease on the wheel studs or nuts when the
spare tire is installed. This could cause the nuts to become loose and lead to an accident. Never place a tire or tire changing tools in the passenger
compartment after changing wheels. In a sudden stop or colli-
sions, loose equipment could strike occupants and cause injury.Store the tire and all tools in the proper place.
If you have a flat tire while driving, never brake suddenly; keep driving
straight ahead while gradually reducing speed. Then slowly pull off the
road to a safe place.
1. Park on a hard, level surface, whenever possible, then stop the en- gine.
2. Set the parking brake securely and shift a manual transmission ve-
hicle in reverse or an automatic transmission vehicle in the “P” (Park)
position.
3. Turn on the hazard warning flasher and have everyone get out of thevehicle.
4. Put wheel blocks at the front and rear of the tire diagonally opposite
the flat tire.
OM-H2259
Jacking position
Wheel blocks

9-8
6. (If your vehicle has wheel covers) Insert the wheel nut wrench into the
notch provided in the wheel cover, and pry it off.
OM-H0376HB9032BA
7. Loosen the wheel nuts using the wheel nut wrench but do not remove the nuts.
8. Place the jack under the side sill at the front or rear jack-up point clos-
est to the flat tire.
HB9012BB
OM-H2262
Turn the jackscrew by hand until the jack head engages firmly into the jack-up point.
If your vehicle is equipped with side sill skirts, jack-up points are pointed
to by arrow marks on the underside of the side sill skirt. Place the jack
under the front or rear jack-up point closest to flat tire.

In case of emergency9-9
–
CONTINUED –
9. Insert the jack handle into the jackscrew, and turn the handle until the
tire clears the ground. Do not raise the vehicle higher than necessary.
OM-H2263
10. Remove the wheel nuts and the flat tire.
11. Before putting the spare tire on, clean the mounting surface of thewheel and hub with a cloth.
HG0104
OM-H0172
12. Put on the spare tire. Replace the wheel nuts. Tighten them by hand.
13. Turn the jack handle counterclockwise to lower the vehicle.

9-10
14. Use the wheel nut wrench to securely tighten the wheel nuts to the
specified torque, following the tightening order in the illustration.
OM-H0377
The torque for tightening the nuts is 58 to 72 ft-lb (78 to 98 N-m, 8 to 10
kg-m). This torque is equivalent to applying about 88 to 110 lbs (40 to 50
kg) at the top of the wheel nut wrench. Never use your foot on the wheel
nut wrench or a pipe extension on the wrench because you may exceed
the specified torque. Have the wheel nut torque checked at the nearest
automotive service facility.
15. Store the flat tire in the spare tire compartment.
HS0153
Flat tireAttaching bolt
Spacer
When storing a conventional tire, put the spacer upside down and tight-
en the attaching bolt firmly.
Also store the jack and wheel nut wrench in their storage locations.

In case of emergency9-27
–
CONTINUED –
Screwdriver
Wheel nut wrench
Hex-headed wrench (for vehicles with moonroof)
Jack and jack handle
HB9001BA
HBF015CB
Jack handle
Jack
Spare tire
HB7008CA
HB8004BD
The jack is stored on the left side of the trunk or cargo area.
To take out the jack, turn the jackscrew counterclockwise to loosen it,
then remove the jack.
The jack handle is stored under the spare tire cover.
For how to use the jack, refer to “Flat tires ”.

11-46
Wheel covers Removing the wheel cover
HB9032BA
Insert the wheel nut wrench into the notch provided, and pry the
wheel cover off. Installing the wheel cover
HGA013BA
Align the valve with the valve hole in the cover, then fit the cover on
the wheel by tapping your hand evenly around the circumference of
the cover.
NOTE
When any of the wheels is removed and replaced for tire rotation or
to change a flat tire, always check the tightness of the wheel nuts af-
ter driving approximately 600 miles (1,000 km). If any nut is loose,

Maintenance and service11-47
–
CONTINUED –
tighten it to the specified torque.
Aluminum wheels (If equipped)
Aluminum wheels can be scratched and damaged easily. Handle them
carefully to maintain their appearance, performance, and safety. When any of the wheels is removed and replaced for tire rotation or to
change a flat, always check the tightness of the wheel nuts after driving
approximatly 600 miles (1,000 km). If any nut is loose, tighten it to the
specified torque. Never apply oil to the threaded parts, wheel nuts, or tapered surface
of the wheel. Never let the wheel rub against sharp protrusions or curbs.
Be sure to fit tire chains on uniformly and completely around the tire,
otherwise the chains may scratch the wheel. When wheel nuts, balance weights, or the center cap is replaced, be
sure to replace them with genuine SUBARU parts designed for aluminumwheels.
Windshield washer fluid
CAUTION
Never use engine coolant as washer fluid because it could cause paint damage.
Check the level of the washer fluid at each fuel stop. If the level is low, fill
the fluid up to the neck of the reservoir.Use windshield washer fluid. If windshield washer fluid is unavailable use
clean water.
In areas where water freezes in winter, use an anti-freeze type windshield
washer fluid. SUBARU Windshield Washer Fluid contains 58.5% methyl
alcohol and 41.5% surfactant, by volume. Its freezing temperature varies
according to how much it is diluted, as indicated below.

Specifications12-15
–
CONTINUED –
Vehicle identification
HBD002BB
1 Emission control label
2 Vehicle identification number
3 Radio noise label (Canada model)
4 Vacuum hose connectionslabel 5
Tire inflation pressure label
6 Certification and bar cordlabel
7 Vehicle identification numberplate
8 Model number plate