lock SUBARU OUTBACK 2005 4.G Manual PDF

3-9
Instruments and controls
– CONTINUED –
Briefly press the knob to return to the A trip meter indi-
cation.
If you turn the ignition switch to the “LOCK” position,
turn the ignition switch to the “ON” position, or open
and close the driver’s door during the setting proce-
dure, the new setting will be canceled.
Also, if you do not press the trip knob for a period of 10
seconds, the new setting will be canceled.
NOTE
It is not possible to cancel sequential illumination
of the combination meter while sequential illumi-
nation is actually taking place. Cancel sequential
illumination when regular illumination (for driving)
has begun. !Speedometer
The speedometer shows the vehicle speed. !
Odometer
This meter displays the odometer when the ignition
switch is in the “LOCK”, “ACC” or “ON” position.
The odometer shows the total distance that the vehicle
has been driven.
If you press the trip knob when the ignition switch is in
the “LOCK” position, the odometer/trip meter will light
up. If you do not press the trip knob within 10 seconds
of illumination of the odometer/trip meter, the odome-
ter/trip meter will go off.
The odometer/trip meter will also go off if you open
and close the driver’s door or turn the ignition switch to
UB3523BA

3-10
Instruments and controls
the “ON” position within 10 seconds of illumination of
the odometer/trip meter. !
Double trip meter
This meter display two trip meters when the ignition
switch is in the “LOCK”, “ACC” or “ON” position.
The trip meter shows the distance that the vehicle has
been driven since you last set it to zero.
To change the mode indication, briefly push the knob.
Each press of the knob changes the mode indication
alternately. To set the trip meter to zero, select the A trip or B trip
meter by pushing the knob and keep the knob pushed
for more than 2 seconds.
If you press the trip knob when the ignition switch is in
the “LOCK” position, the odometer/trip meter will light
up. It is possible to switch between the A trip meter
and B trip meter indications while the odometer/trip
meter is lit up. If you do not press the trip knob within
10 seconds of illumination of the odometer/trip meter,
the odometer/trip meter will go off. Also, if you open
and close the driver’s door within 10 seconds of illumi-
nation of the odometer/trip meter, the odometer/trip
meter will go off.
To ensure safety, do not attempt to change the
function of the indicator during driving, as an
accident could result.
UB3524AA
A trip meter
B trip meter

3-12
Instruments and controls
remaining in the tank.
When the ignition switch is in the “LOCK” or “ACC” po-
sition, the fuel gauge shows “E” even if the fuel tank
contains fuel.
The gauge may move slightly during braking, turning
or acceleration due to fuel level movement in the tank.
If you press the trip knob while the ignition switch is in
the “LOCK” position, the fuel gauge’s dial, needle, and
rim will light up and the needle will indicate the amount
of fuel remaining in the tank.
If, while the fuel gauge needle is indicating the amount
of fuel remaining in the tank, you (a) do not press the
trip knob for 10 seconds or (b) open and close the driv-
er’s door, the fuel gauge needle will drop to the “E” po-
sition and the dial, needle, and rim will go off.
The rim of the fuel gauge flashes five time when the
amount of remaining fuel reaches 2.6 US gal (10 liters,
2.2 lmp gal).
If you turn the ignition switch to the “LOCK” position
and back to the “ON” position, the rim will again flash five times.
UB3211BA

3-15
Instruments and controls
– CONTINUED –
!Canceling the function for meter/
gauge needle movement upon turning
on the ignition switch
It is possible to activate or deactivate the movement of
the meter needles and gauge needles that takes place
when the ignition switch is turned to the “ON” position.
Turn the ignition switch to the “ACC” position. With the
A trip meter indication selected, briefly press the trip
knob twice. You can now establish the activated/deac-
tivated setting for movement of the meter needles and
gauge needles. To change the current setting, press
the trip knob for at least two seconds. : Activated
: Deactivated
Briefly press the knob to return to the A trip meter indi-cation.
If you turn the ignition switch to the “LOCK” position,
turn the ignition switch to the “ON” position, or open
and close the driver’s door during the setting proce-
dure, the new setting will be canceled. Also, if you do
not press the trip knob for a period of 10 seconds, the
new setting will be canceled.
NOTE
It is not possible to cancel sequential illumination
of the combination meter while sequential illumi-
nation is actually taking place. Cancel sequential
illumination when regular illumination (for driving)
has begun. ! Speedometer
The speedometer shows the vehicle speed.
UB3533AA

3-16
Instruments and controls
!
Odometer
This meter displays the odometer when the ignition
switch is in the “LOCK”, “ACC” or “ON” position.
The odometer shows the total distance that the vehicle
has been driven.
If you press the trip knob when the ignition switch is in
the “LOCK” position, the odometer/trip meter will light
up. If you do not press the trip knob within 10 seconds
of illumination of the odometer/trip meter, the odome-
ter/trip meter will go off.
Also, if you open and close the driver’s door within 10
seconds of illumination of the odometer/trip meter, the
odometer/trip meter will go off. !
Double trip meter
This meter displays the two trip meters when the igni-
tion switch is in the “LOCK”, “ACC” or “ON” position.
The trip meter shows the distance that the vehicle has
been driven since you last set it to zero.
To change the mode indication, briefly push the knob.
Each press of the knob changes the mode indication
alternately.
UB3523BAUB3524AA

3-17
Instruments and controls
– CONTINUED –
To set the trip meter to zero, select the A trip or B trip
meter by pushing the knob and keep the knob pushed for more than 2 seconds.
If you press the trip knob when the ignition switch is in
the “LOCK” position, the odometer/trip meter will light
up. It is possible switch between the A trip meter and
B trip meter indications while the odometer/trip meter
is lit up. If you do not press the trip knob within 10 sec-
onds of illumination of the odometer/trip meter, the
odometer/trip meter will go off.
Also, if you open and close the driver’s door within 10
seconds of illumination of the odometer/trip meter, the
odometer/trip meter will go off.
To ensure safety, do not attempt to change the
function of the indicator during driving, as an
accident could result.
NOTE
If the connection between the combination meter
and battery is broken for any reason such as vehi-
cle maintenance or fuse replacement, the data re-
corded on the trip meter will be lost. !Vehicle communication system fault indication
The vehicle communication system carries various
types of information (vehicle speed, running condi-
tions, etc.) to control modules. In the event of a fault in
this communication system, the trip meter will show“” .
If the trip meter shows “ ”, immediately contact the
nearest SUBARU dealer and have the vehicle com-
munication system inspected.
NOTE
If you press the trip knob while the trip meter is
showing “ ”, the trip meter indication will ap-
pear for 10 seconds. ! Tachometer
The tachometer shows the engine speed in thousands
of revolutions per minute.
A trip meter
B trip meter

3-18
Instruments and controls
Do not operate the engine with the pointer of
the tachometer in the red zone. In this range,
fuel injection will be cut by the engine control
module to protect the engine from overrevving.
The engine will resume running normally after
the engine speed is reduced below the red
zone.
NOTE (3.0-liter models only)
To protect the engine while the “P” or “N” position
is selected, the engine is controlled such that the
engine speed does not become too high even if
the accelerator pedal is pressed hard.
!
Fuel gauge
The fuel gauge shows the approximate amount of fuel
remaining in the tank.
The gauge does not return to “E” even though the ig-
nition switch is in the “ACC” or “LOCK” position.
The gauge may move slightly during braking, turning
or acceleration due to fuel level movement in the tank.
If you press the trip knob while the ignition switch is in
the “LOCK” position, the fuel gauge’s dial will light up
and the needle will indicate the amount of fuel remain-
ing in the tank.
If, while the fuel gauge needle is indicating the amount
of fuel remaining in the tank, you (a) do not press the
UB3212AA

3-23
Instruments and controls
– CONTINUED –
seconds later (21 seconds after turning ON the ignition
switch), the warning lights will alternate between flash-
ing and steady illumination at 15-second intervals, and
the chime will sound while the warning light(s) is/are
flashing.
Alternate flashing and steady illumination of the warn-
ing lights and sounding of the chime will continue until
both driver and front passenger fasten their seatbelts.
NOTE "If the driver and/or front passenger unfasten(s)
the seatbelt(s) after fastening, the seatbelt warn-
ing device operates as follows according to the
vehicle speed. "At speeds lower than approximately 9 mph (15
km/h)
The warning light(s) for unfastened seatbelt(s)
will alternate between flashing and steady illu-
mination at 15-second intervals. The chime will
not sound. " At approximately 9 mph (15 km/h) or higher
speeds
The warning light(s) for unfastened seatbelt(s)
will alternate between flashing and steady illu-
mination at 15-second intervals and the chime
will sound while the warning light(s) is/are flash-
ing.
" If you unfasten and refasten driver’s seatbelt three times within six seconds after turning ON
the ignition switch, the warning operation that fol-lows the 6-second warning after turning ON the ig-
nition switch is canceled. When the ignition switch
is turned ON next time, however, the complete se-
quence of warning operation resumes.
If there is no passenger on the front passenger’s seat,
the seatbelt warning device for front passenger’s seat
will be deactivated. The front passenger’s occupant
detection system monitors whether or not there is a
passenger on the front passenger’s seat. Observe the
following precautions. Failure to do so may prevent
the device from functioning correctly or cause the de-
vice to fail."
Do not install any accessory such as a table or TV
onto the seatback." Do not store a heavy load in the seatback pocket.
" Do not allow the rear seat occupant to place his/her
hands or legs on the front passenger’s seatback, or al-
low him/her to pull the seatback." Do not use front seats with their backward-forward
position and seatback not being locked into place se-
curely. If any of them are not locked securely, adjust
them again. For adjusting procedure, refer to the
“Manual seat” in the front seats section in Chapter 1 in
this owner’s manual. (Models equipped with manualseats only)

3-24
Instruments and controls
If the seatbelt warning device for front passenger’s
seat does not function correctly (e.g., it is activated
even when the front passenger’s seat is empty or it is
deactivated even when the front passenger has not
fastened his/her seatbelt), take the following actions."
Ensure that no article is placed on the seat other
than the child restraint system and the child occupant." Ensure that there is no article left in the seatback
pocket. " Ensure that the backward-forward position and
seatback of front passenger’s seat are locked into
place securely by moving the seat back and forth.
(Models equipped with manual seats only)
If still the seatbelt warning device for front passenger’s
seat does not function correctly after taking relevant
corrective actions described above, immediately con-
tact your SUBARU dealer for an inspection. ! SRS airbag system warning light
When the ignition switch is turned to the “ON” position,
the SRS airbag system warning light will come on for
about seven seconds and go out. This shows the SRS
frontal airbag and SRS side airbag and SRS curtain
airbag and seatbelt pretensioners are in normal oper-
ation. If this light comes on while driving or remains illuminat-
ed even after a period of about 7 seconds from when
the ignition has been turned on, it may indicate that the
SRS frontal airbag system or SRS side airbag system
(if equipped) or SRS curtain airbag or seatbelt preten-
sioner system is not working properly. Contact your
nearest SUBARU dealer immediately. !
Front passenger’s frontal airbag ON
and OFF indicators
“ ”: Front passenger’s frontal airbag ON
indicator
PASS AIR BAGPASS AIR BAGONONOUT.DISPOFF
PASS AIR BAG
OFFON
UB3208EA
ON or

3-25
Instruments and controls
– CONTINUED –
“ ”: Front passenger’s frontal airbag
OFF indicator
The front passenger’s frontal airbag ON and OFF indi-
cators show you the status of the front passenger’s
SRS frontal airbag.
The indicators are located next to the clock in the cen-
tral portion of the instrument panel.
When the ignition switch is turned to the “ON” position,
both the ON and OFF indicators illuminate for 6 sec- onds during which time the system is checked. Follow-
ing the system check, both indicators extinguish for 2
seconds. After this, one of the indicators illuminates
depending on the status of the front passenger’s SRS
frontal airbag reached by the Subaru advanced frontal airbag system monitoring.
If the front passenger’s SRS frontal airbag is activated,
the passenger’s frontal airbag ON indicator will illumi-
nate while the OFF indicator will remain extinguished.
If the front passenger’s SRS frontal airbag is deacti-
vated, the passenger’s frontal airbag ON indicator will
remain extinguished while the OFF indicator will illumi-
nate.
If both the ON and OFF indicators remain lit or extin-
guished simultaneously, the system is faulty. Contact
your SUBARU dealer immediately for an inspection. !
CHECK ENGINE warning light/
Malfunction indicator lamp
If the CHECK ENGINE light comes on while you
are driving, have your vehicle checked/repaired
by your SUBARU dealer as soon as possible.
Continued vehicle operation without having the
emission control system checked and repaired
as necessary could cause serious damage,
which may not be covered by your vehicle’s
warranty.
If this light comes on steadily or blinks while the engine
is running, it may indicate that there is a problem or po-
tential problem somewhere in the emission control system. ! If the light comes on steadily:
If the light comes on steadily while driving or does not
go out after the engine starts, an emission control sys-
tem malfunction has been detected.
You should have your vehicle checked by an autho-
rized SUBARU dealer immediately.
OFF or