light SUBARU OUTBACK 2005 4.G Manual Online

3-33
Instruments and controls
– CONTINUED –
sidered normal. "The warning light comes on right after the en-
gine is started but goes out immediately, remain-
ing off. " The warning light comes on after engine startup
and goes off while the vehicle is subsequently be-
ing driven. " The warning light comes on during driving, but
it goes out immediately and remains off. ! Vehicle Dynamics Control OFF indicator light
" It comes on when the Vehicle Dynamics Control
OFF switch is pressed. " It also comes on when the Vehicle Dynamics Con-
trol system is deactivated.
NOTE " The light may stay on for a while after the engine
has been started, especially in cold weather. This
does not indicate the existence of a problem. The
light should go out as soon as the engine has
warmed up. " The indicator light comes on when the engine
has developed a problem and the Malfunction in-
dicator light is on.
The Vehicle Dynamics Control system is probably
faulty under the following condition. Have your vehicle checked at a SUBARU dealer as soon as possible."
The light does not go out even after the lapse of sev-
eral minutes (the engine has warmed up) after the en-
gine has started. ! Security indicator light
This indicator light shows the status of the alarm sys-
tem. If your vehicle is equipped with an immobilizer, it
also indicates operation of the immobilizer system. ! Alarm system
It blinks to show the driver the operational status of the
alarm system. For detailed information, refer to the
“Alarm system” in Chapter 2. ! Immobilizer system (if equipped)
This light blinks about 60 seconds after the ignition
switch is turned from “ON” position to the “ACC” or
“LOCK” position or immediately after the key is pulled
out. (Refer to the “Door locks” section in chapter 2.)
If the indicator light does not flash, it may indicate that
immobilizer system may be faulty. Contact your near-
est SUBARU dealer immediately.
In the event that an unauthorized key (for example, an
unauthorized duplicate) is used, the security indicator
light comes on.

3-34
Instruments and controls
!
SPORT mode indicator light (AT
vehicles)
This light comes on when the ignition switch is turned
to the “ON” position and goes out after the engine has
started. When the selector lever is moved to the man-
ual gate, the SPORT mode is selected and the indica-
tor light comes on. (Refer to the “Automatic transmis-
sion – 4 speed” or “Automatic transmission – 5 speed”
section in chapter 7.) ! Selector lever position indicator (AT
vehicles)
This indicator shows the position of the selector lever. !
Gear position indicator (AT vehicles)
When the manual mode is selected, the gear position
indicator (which shows the current gear selection) and
the upshift/downshift indicator light up. (Refer to the
“Automatic transmission – 4 speed” or “Automatic
transmission – 5 speed” section in chapter 7.) ! Turn signal indicator lights
These lights show the operation of the turn signal or
lane change signal.
If the indicator lights do not blink or blink rapidly, the
turn signal bulb may be burned out. Replace the bulb
as soon as possible. Refer to the “Replacing bulbs”
UB3532AA
UB7527CA

3-35
Instruments and controls
– CONTINUED –
section in chapter 11. !High beam indicator light
This light shows that the headlights are in the high
beam mode.
This indicator light also comes on when the headlight
flasher is operated. ! Cruise control indicator light
The cruise control indicator light comes on when the
ignition switch is turned to the “ON” position and goes
out after about three seconds.
This light comes on when the “CRUISE” main switch
is pressed.
If you move the cruise control lever while turning the
ignition switch “ON”, the cruise control function is de-
activated and the “CRUISE” indicator light flashes. To
reactivate the cruise control function, turn the ignition
switch back to the “ACC” or “LOCK” position, and then
turn it again to the “ON” position. ! Cruise control set indicator light
The cruise control set indicator light comes on when
the ignition switch is turned to the “ON” position and
goes out after about three seconds.
This light comes on when vehicle speed has been set. !
Headlight indicator light
This indicator light comes on when the light switch is
turned to the “ ” position (to turn on the parking
lights) or to the “ ” position (to turn on the head-
lights). ! Front fog light indicator light
This indicator light is on while the front fog lights are on.

3-41
Instruments and controls
– CONTINUED –
Canada-spec. vehicles
This indication shows the average rate of fuel con-
sumption since the trip meter was last reset.
Pressing the trip knob toggles the indication between
the average fuel consumption corresponding to the A
trip meter indication and the average fuel consumption
corresponding to the B trip meter indication.
When either of the trip meter indications is reset, the
corresponding average fuel consumption value is alsoreset.
NOTE " The indicated values vary in accordance with
changes in the vehicle’s running conditions. Also, the indicated values may differ slightly from the
actual values and should thus be treated only as a
guide. "
When either trip meter indication is reset, the av-
erage fuel consumption corresponding to that trip
meter indication is not shown until the vehicle has
subsequently covered a distance of 1 mile (or 1 km). ! Driving range on remaining fuel
U.S.-spec. vehicles
UB3203AA
UB3570AA

3-42
Instruments and controls
Canada-spec. vehicles
The driving range indicates the distance that can be
driven taking into account the amount of fuel remain-
ing in the tank and the average rate of fuel consump- tion.
When the low fuel warning light comes on, the driving
range indication flashes for five seconds. (The display
first switches to the driving range indication if it was
originally giving some other indication.) U.S.-spec. vehicles
UB3538AAUB3572AA

3-43
Instruments and controls
– CONTINUED –
Canada-spec. vehicles
If the driving range is shown as “ ”, there is only
a tiny amount of fuel left in the tank. You must refuel
the vehicle immediately.
NOTE
The driving range on remaining fuel is only a
guide. The indicated value may differ from the ac-
tual driving range on remaining fuel, so you must
immediately fill the tank when the low fuel warning
light comes on. !
Journey time
The journey time shows the time that has elapsed
since the ignition switch was turned to the “START”
position.
UB3542AA
UB3539AA

3-44
Instruments and controls
The journey time indication flashes each time a com-
plete hour has elapsed. If the display is giving an indi-
cation other than the journey time, the display switch-
es to the journey time, flashes for five seconds, and re-
turns to its original indication each time a complete
hour has elapsed.
NOTE
The journey time is reset when the ignition switch
is turned to the “OFF” position. It is also reset if
the ignition switch is turned to the “LOCK” or
“ACC” position prior to restarting of the engine.
Light control switch
To prevent battery discharge resulting from ac-
cidentally leaving your lights on when your ve-
hicle is parked, the light switch operates only
when the ignition switch is in the “ON” posi-
tion. In any other position, the vehicle’s lights
will be out.
If you park your vehicle on a roadside at night,
use the hazard warning flasher to alert the other
drivers.
The light switch operates only when the ignition switch
is in the “ON” position.UB3540AA

3-45
Instruments and controls
– CONTINUED –
!Headlights
To turn on the headlights, turn the knob on the end of
the turn signal lever. first position
Parking lights, instrument panel illumination, tail lights
and license plate light are on.
second position
Headlights, parking lights, instrument panel illumina-
tion, tail lights, and license plate light are on. !
High/low beam change (dimmer)
To change from low beam to high beam, push the turn
signal lever forward. When the headlights are on high
beam, the high beam indicator light “ ” on the in-
strument panel is also on.
To switch back to low beam, pull the lever back to the
detent position.
UB3204BAUB3205BA

3-46
Instruments and controls
!
Headlight flasher
Do not hold the lever in the flashing position for
more than just a few seconds.
To flash the headlights, pull the lever toward you and
then release it. The high beam will stay on for as long
as you hold the lever. The headlight flasher works
even though the lighting switch is in the “OFF” posi-tion.
When the headlights are on high beam, the high beam indicator light “ ” on the instrument panel also
comes on. !
Daytime running light system
The tail lights, parking lights, and side marker
lights are not turned on by the daytime running
light system. The light switch must always be
turned to the “ ” position when it is dark
outside.
The low beam headlights will automatically come on at
reduced brightness when the engine has started, un-
der the following conditions:" The parking brake is fully released.
" The light switch is in the “OFF” or “ ” position.
UB3205CA

3-47
Instruments and controls
– CONTINUED –
Turn signal lever
To activate the right turn signal, push the turn signal le-
ver up. To activate the left turn signal, push the turn
signal lever down. When the turn is finished, the lever
will return automatically. If the lever does not return af-
ter cornering, return the lever to the neutral position by
hand.
To signal a lane change, push the turn signal lever up
or down slightly and hold it during the lane change.
The turn signal indicator lights will flash in the direction
of the turn or lane change. The lever will return auto-
matically to the neutral position when you release it.Illumination brightness control
When the lighting switch is in the “ ” or “ ”
position, you can adjust brightness of the instrument
panel illumination for better visibility.
In turbo models, you can also adjust the brightness of
the instrument panel illumination when the lighting
switch is in the OFF position.
To brighten, turn the control dial upward.
To darken, turn the control dial downward.
UB3205DAUB3206BA