manual transmission SUBARU OUTBACK 2018 Quick Guide
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2018, Model line: OUTBACK, Model: SUBARU OUTBACK 2018Pages: 33, PDF Size: 3.3 MB
Page 23 of 33
21
Controls
Cruise Control
Increase Speed
Push up the “RES/SET” switch to
the “RES” side; hold until your vehicle
reaches the desired speed and
release. To increase speed using the
accelerator pedal, press the pedal
until you reach the desired speed.
Push down the “RES/SET” switch to
the “SET” side to set the speed.Decrease Speed
Push down the “RES/SET” switch to
the “SET” side; hold until your vehicle
slows to the desired speed and release.
To decrease the speed using the brake
pedal, press the pedal to release
cruise control temporarily. When the
speed decreases to the desired speed,
push down the “RES/SET” switch to
the “SET” side to set the speed.To activate the cruise control,
press the “
” button.
The indicator light on the
instrument panel will turn on.
To deactivate cruise control,
press the “
” button again.
Press the accelerator pedal until your
vehicle reaches the desired speed. Push
the switch to the “SET” side and release.
Ease off the accelerator pedal. Your
vehicle will maintain the desired speed. To cancel the cruise control,
push the brake pedal or press
the “CANCEL” button. If you
have a manual transmission, you
can push in the clutch pedal.
To resume your speed after
canceling, push the switch
to the “RES” side.
2926966_18a_Subaru_Outback_QRG_050417.indd 215/4/17 3:37 PM
Getting
StartedInstrument
Panel Gauges
Personalize ControlsWhile
Operating Safety/In Case
of Emergency Additional
Information
Page 24 of 33
22
Electronic Parking Brake
To apply, push the brake pedal and pull up the parking
brake switch. The brake system warning light on
the instrument panel and the indicator light on the
parking brake switch will illuminate.
To release, make sure all doors are closed and your
seatbelt is fastened, then gently push the accelerator
pedal. Or, while the ignition switch is in the ON position
and the brake pedal is pushed in, push down the
parking brake switch.
X-MODE® (if equipped)
X-MODE® is the integrated control system of the engine,
AWD and Vehicle Dynamics Control system. Press the
X-MODE button to activate. Press it again to deactivate.
Please refer to your Owner’s Manual for operational
parameters and details about this feature.
While Operating
Paddle Shift Control Switches (if equipped)
• Temporary use: Even when the selector is in the
“D” (Drive) position, you can temporarily shift the
gear by pulling the “+” or “–” paddle shift control
switch. The transmission will automatically
switch back to Normal Mode.
• When the selector lever is in Manual Mode,
shift to the next higher gear by pulling the “+” paddle shift cont\
rol switch on the steering
wheel. Pull the “–” paddle shift control switch to shift into the next lower gear.
Manual Shifting Operation
Arrow-shaped lights in the center of the instrument panel show whether an u\
pshift is possible
and whether a downshift is possible.
Hill Holder™ Function
To activate, press the Hill Holder switch. To deactivate, press the Hill Holder switch again.
When the Hill Holder function is activated, the parking brake will be au\
tomatically applied when
stopped on an uphill or downhill slope with the brake pedal pushed down.\
The brake system
warning light on the instrument panel and the indicator light on the parkin\
g brake
switch will illuminate.
2926966_18a_Subaru_Outback_QRG_050417.indd 225/4/17 3:37 PM
Page 25 of 33
23
While
Operating
1
Automatic Transmission Shift Mode
The Continuously Variable Transmission (CVT) gives you ultimate control with two
different driving modes: Normal Mode and Manual Mode.
Normal Mode
When the selector lever is in the “D” (Drive) position, the tran\
smission is in Normal
shift mode. The shift position indicator on the instrument panel shows “\
D” and the
transmission automatically shifts into a suitable forward gear.
Manual Mode
In Manual Mode, you select the desired gear position to obtain necessary
acceleration and engine braking. Moving the selector lever left into the\
manual gate
1 from the “D” (Drive) position causes the transmission to change in\
to Manual
Mode. To shift, use the paddle shift control switches. The shift position indicator
shows the selected gear position.
2926966_18a_Subaru_Outback_QRG_050417.indd 235/4/17 3:37 PM
Getting
StartedInstrument
Panel Gauges
Personalize ControlsWhile
Operating Safety/In Case
of Emergency Additional
Information