ignition SUZUKI ALTO 2013 7.G User Guide

2-22
BEFORE DRIVING
53MH0-74E
Installation with Lap-Shoulder Seat
Belts
ELR type belt (if equipped)
53M-04-048
Install your child restraint system accord-
ing to the instructions provided by the child
restraint system manufacturer.
Make sure that the seat belt is securely
latched.
Try to move the child restraint system in all
directions to make sure it is securely
installed.
Supplemental Restraint
System (air bag) (if equipped)
Your vehicle is equipped with a Supple-
mental Restraint System consisting of the
following components in addition to a lap-
shoulder belt at each front seating position.
1) Driver’s front air bag module (if
equipped)
2) Front passenger’s front air bag module
(if equipped)
3) Seat belt pretensioners (if equipped)
4) Air bag controller (if equipped)
5) Forward crash sensor (if equipped)
53MM02013
53M-04-050
If the “AIR BAG” light on the instrument
cluster does not blink or come on when the
ignition switch is first turned to the “ON”
position, or the “AIR BAG” light stays on, or
comes on while driving, the air bag system
may not work properly. Have the air bag
system inspected by an authorized MAR-
UTI SUZUKI dealer as soon as possible.
EXAMPLEWA R N I N G
This section of the owner’s manual
describes the protection provided by
your MARUTI SUZUKI SUPPLEMEN-
TAL RESTRAINT SYSTEM (air bag).
Please read and follow ALL these
instructions carefully to minimize
your risk of severe injury or death in
the event of a collision.
(2)
(3)
(4)(1)
(3)(5)
EXAMPLE

2-27
BEFORE DRIVING
53MH0-74E
53M-04-068
Note that even though your vehicle may be
moderately damaged in a frontal collision,
the collision may not have been severeenough to trigger the air bags to inflate. If
your vehicle sustains ANY front-end dam-
age, have the air bag system inspected by
an MARUTI SUZUKI authorized dealer to
ensure it is in proper working order.
Your vehicle is equipped with a diagnostic
module which records information about
the air bag system if the air bags deploy in
a crash. The module records information
about overall system status, which sensors
activated the deployment, and for a certain
vehicle only, whether the driver’s seat belt
was in use.
Servicing the air bag system
If the air bags inflate, have the air bags and
related components replaced by an autho-
rized MARUTI SUZUKI dealer as soon as
possible.
If your vehicle ever gets in deep water and
the driver’s floor is submerged, the air bag
controller could be damaged. If it does,
have the air bag system inspected by the
MARUTI SUZUKI dealer as soon as possi-
ble.
Special procedures are required for servic-
ing or replacing an air bag. For that reason,
only an authorized MARUTI SUZUKI
dealer should be allowed to service or
replace your air bags. Please remind any-
one who services your MARUTI SUZUKI
that it has air bag.
Service on or around air bag components
or wiring must be performed only by an
MARUTI SUZUKI authorized dealer.
Improper service could result in unin-tended air bag deployment or could render
the air bag inoperative. Either of these two
conditions may result in severe injury.
To prevent damage or unintended inflation
of the air bag system, be sure the battery
is disconnected and the ignition switch has
been in the “LOCK” position for at least 90
seconds before performing any electrical
service work on your MARUTI SUZUKI. Do
not touch air bag system components or
wires. The wires are wrapped with yellow
tape or yellow tubing, and the couplers are
yellow for easy identification.
Scrapping a vehicle that has an uninflated
air bag can be hazardous. Ask your dealer,
body repair shop or scrap yard for help
with disposal.
WA R N I N G
• The driver should not lean over the
steering wheel. In these situations,
the out-of-position occupant would
be too close to an inflating air bag,
and may suffer severe injury.
• Do not attach any objects to, or
place any objects over, the steering
wheel. Do not place any objects
between the air bag and the driver.
These objects may interfere with air
bag operation or may be propelled
by the air bag in the event of a
crash. Either of these conditions
may cause severe injury.
EXAMPLE

2-30
BEFORE DRIVING
53MH0-74E
Warning and Indicator Lights
Brake System Warning Light
53M-04-072
Three different types of operations exist
depending on the vehicle’s specification.
1) The light comes on briefly when the
ignition switch is turned to the “ON”
position.
2) The light comes on when the parking
brake is engaged with the ignition
switch in the “ON” position.
3) The light comes on when under either
or both of above two conditions.
The light also comes on when the fluid in
the brake fluid reservoir falls below the
specified level.
The light should go out after starting the
engine and fully releasing the parking
brake, if the fluid level in the brake fluid res-
ervoir is adequate.
The light also comes on together with the
ABS warning light when the rear brake
force control function (proportioning valve
function) of the ABS system fails.
If the brake system warning light comes on
while you are driving the vehicle, it maymean that there is something wrong with
the vehicle’s brake system. If this happens,
you should:
1) Pull off the road and stop carefully.
2) Test the brakes by carefully starting and
stopping at the side of the road.
– If you determine that it is safe, drive
carefully at low speed to the nearest
dealer for repairs, or
– Have the vehicle towed to the nearest
dealer for repairs.
NOTE:
Because the disc brake system is self-
adjusting, the fluid level will drop as the
brake pads become worn. Replenishing
the brake fluid reservoir is considered nor-
mal periodic maintenance.
Seat Belt Warning Light
(if equipped)
53M-04-073
WA R N I N G
Remember that stopping distance
may be longer, you may have to push
harder on the pedal, and the pedal
may go down farther than normal.
WA R N I N G
If any of the following conditions
occur, you should immediately ask
your MARUTI SUZUKI dealer to
inspect the brake system.
• If the brake system warning light
does not go out after the engine
has been started and the parking
brake has been fully released.
• If the brake system warning light
does not come on when the igni-
tion switch is turned to the “ON”
position.
• If the brake system warning light
comes on at any time during vehi-
cle operation.

2-31
BEFORE DRIVING
53MH0-74E
If the driver’s seat belt is unbuckled when
the ignition switch is turned to the “ON”
position, this light will blink until the driver’s
seat belt is buckled.
For details about the seat belt reminder,
refer to “Seat Belts and Child Restraint
Systems” in this section.
“AIR BAG” Light (if equipped)
53M-04-074
This light blinks or comes on for several
seconds when the ignition switch is turned
to the “ON” position so you can check if the
light is working.
The light will come on and stay on if there
is a problem in the air bag system.
Malfunction Indicator Light
53M-04-075
Your vehicle has a computer-controlled
emission control system. A malfunction
indicator light is provided on the instrument
panel to indicate when it is necessary to
have the emission control system serviced.
The malfunction indicator light comes on
when the ignition switch is turned to “ON”
position to let you know the light is working
and goes out when the engine is started.
If the malfunction indicator light comes on
when the engine is running, there is a
damage with the emission control system.
Bring the vehicle to your MARUTI SUZUKI
dealer to have the damage fixed.
Also, if the light comes on, there may be
something wrong with the transaxle sys-
tem. Have the system inspected by MAR-
UTI SUZUKI authorized dealer.Transaxle Warning Light
(if equipped)
53M-04-076
This light comes on briefly when the igni-
tion switch is turned to the “ON” position or
the engine switch is pressed to change the
ignition mode to “ON” so you can check the
light is working.
If this light comes on when the engine is
running, there is the problem with the auto-
matic transaxle system. Ask your MARUTI
SUZUKI dealer to have the system
inspected.
NOTE:
If the automated manual transaxle system
temperature becomes too high, this light
will blink. Stop the vehicle in a safe place
and let the system cool down.
WA R N I N G
If the “AIR BAG” light does not blink
or come on briefly when the ignition
switch is turned to the “ON” position,
stays on for more than 10 seconds,
or comes on while driving, the air bag
system may not work properly. Have
both systems inspected by an
MARUT SUZUKI authorized dealer.
NOTICE
Continuing to drive the vehicle when
the malfunction indicator light is on
can cause permanent damage to the
vehicle’s emission control system,
and can affect fuel economy and
driveability.

2-32
BEFORE DRIVING
53MH0-74E
Electric Power Steering Light
(if equipped)
53M-04-077
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started.
If this light comes on while driving, the
power steering system may not work prop-
erly. Have the system inspected by your
MARUTI SUZUKI dealer.
NOTE:
If the power steering system does not work
properly, you will feel heavier to steer but
you still will be able to steer.
Oil Pressure Light
53M-04-078
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. Thelight will come on and remain on if there is
insufficient oil pressure. If the light comes
on when driving, pull off the road as soon
as you can and stop the engine.
Check the oil level and add oil if necessary.
If there is enough oil, the lubrication sys-
tem should be inspected by your MARUTI
SUZUKI dealer before you drive the vehi-
cle again.
Charging Light
53M-04-079
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. The
light will come on and remain on if there is
something wrong with the battery charging
system. If the light comes on when the
engine is running, the charging system
should be inspected immediately by your
MARUTI SUZUKI dealer.
High Engine Coolant Temperature
Warning Light
53M-04-080
When the ignition switch is turned to the
“ON” position, this light comes on briefly so
you can check that the light is working. If
this light blinks while driving, it means the
engine is running hot. Avoid driving condi-
tions that may lead to actual overheating. If
NOTICE
• If you operate the engine with this
light on, severe engine damage can
result.
• Do not rely on the Oil Pressure
Light to indicate the need to add
oil. Be sure to periodically check
the engine oil level.

2-33
BEFORE DRIVING
53MH0-74E
the light stays on without blinking, then the
engine is overheating. Follow the instruc-
tions in the “If the Engine Overheats” of
“EMERGENCY SERVICE” section.
Immobilizer System Light
53M-04-081
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. If this
light blinks with the ignition switch turned to
“ON”, there may be something wrong with
the immobilizer system. Ask your MARUTI
SUZUKI dealer to have the system
inspected.
Door Lock Canceller Indicator Light
(if equipped)
53M-04-082
This indicator light will come on and keep
blinking continuously if there is some prob-
lem with door lock canceller system. Have
the vehicle inspected by MARUTI SUZUKI
authorized dealer.
NOTE:
In case door lock wiring and/or motor
are
damaged, Door Lock Canceller Indicator
Light will not blink.
Gear Shift Indicator (if equipped)Manual Transaxle
53M-04-083
This indicator informs about upshifting or
downshifting the gear while the vehicle is
running.There are three indications:
Upshift Indicator
This symbol indicates that lower gear posi-
tion is selected for vehicle’s current speed
and / or engine revolution. Changing to
higher gear position is recommended.
Stay Indicator
This symbol indicates that current gear
position is optimal for vehicle’s current
speed and / or engine revolution. No gear
shifting is required.
NOTE:
While driving in optimal gear position, the
upshift/downshift indicator does not
appear.
Downshift Indicator
This symbol indicates that higher gear
position is selected for the vehicle’s current
speed and / or engine revolution. Changing
to lower gear position is recommended.
NOTICE
Continuing to drive the vehicle when
engine overheating is indicated can
result in severe engine damage.

2-35
BEFORE DRIVING
53MH0-74E
ALTO K10
Ty p e 1
53M-04-088
Ty p e 2
53M-04-089
The speedometer indicates vehicle speed
in km/h.
Fuel Gauge
ALTO 800
Ty p e 1
53M-04-090
Ty p e 2
53MH0239
ALTO K10
Without tachometer
53M-04-091
With tachometer
53M-04-092
Automated Manual Transaxle
53M-04-093
When the ignition switch is in the “ON”
position, this gauge gives an approximate
indication of the amount of fuel in the fuel
tank. “F” stands for full and “E” stands for
empty.
The mark (1) indicates that the fuel filler
door is located on the left side of the vehi-
cle.
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
(1)
EXAMPLE
EXAMPLE
EXAMPLE

2-37
BEFORE DRIVING
53MH0-74E
With tachometer
53M-04-099
Clock (1) (if equipped)
The clock is shown when the ignition
switch is in the “ON” position.
To set the clock, follow the instructions
below.
Hold in the indication selector and meter
illumination control knob (3) for more
than 2 seconds. Push the indication
selector and meter illumination control
knob (3) to advance the minute display
while the minute display is flashing.
Release the indication selector and
meter illumination control knob (3) for 5
seconds to set the minute display.
The hour display flash after the minute
display is set. Push the indication selec-tor and meter illumination control knob
(3) to advance the hour display. Release
the indication selector and meter illumi-
nation control knob (3) for 5 seconds to
set the hour display.
Odometer/Trip meter (2)
The odometer/trip meter is shown when
the ignition switch is in the “ON” position.
The odometer records the total distance
the vehicle has been driven. The trip meter
can be used to measure the distance trav-
eled on short trips or between fuel stops.
53M-04-100
When the ignition switch is turned to “ON”
with the lighting switch is in the “OFF” posi-
tion, the display shows three types of indi-
cation; odometer (A), trip meter A (B), trip
meter B (C) and clock (D). Push the
“MODE” knob (3) quickly to switch the indi-
cation among the four.
53M-04-101
WA R N I N G
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
Do not attempt to adjust the display
while driving.
EXAMPLE
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
EXAMPLE
EXAMPLE

2-38
BEFORE DRIVING
53MH0-74E
When the ignition switch is turned to “ON”
and the position lights, tail lights and/or the
headlights are on, the display shows four
types of indication; odometer (A), trip
meter A (B), trip meter B (C), clock (D) and
indication of illumination intensity (E). Push
the “MODE” knob (3) quickly to switch the
indication among the five. When the indica-
tion shows (E), you can control the meter
illumination intensity. Refer to “Meter illumi-
nation control” section below for details on
how to dim or brighten the meter illumina-
tion.
53M-04-102
To reset the trip meter to zero, hold in the
“MODE” knob (3) for about 2 seconds.Meter illumination control
53M-04-103
When the display shows the indication of
illumination intensity (E), you can dim or
brighten the meter illumination.
To change the meter illumination bright-
ness, continue to hold in the “MODE” knob
(3). The indication will change as shown in
the illustration. The illumination gets dim-
mer then returns to the brightest condition
after it reaches the dimmest.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the brightness of the
instrument panel lights will be reinitialized.
Readjust the brightness according to your
preference.
Lighting Control Lever
53M-04-104EXAMPLE
EXAMPLE
EXAMPLE
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE

2-40
BEFORE DRIVING
53MH0-74E
Headlight Leveling Switch
53M-04-109
Level the headlight beam according to the
load condition of your vehicle by turning
this switch. The chart below shows the
appropriate switch position for different
vehicle-load conditions.
Turn Signal Control Lever
53M-04-110
Turn Signal Operation
With the ignition switch in the “ON” posi-
tion, move the lever up or down to activate
the right or left turn signals.
Normal turn signal
Ty p e 1
53M-04-111
Move the lever all the way upward or down-
ward to signal. When the turn is com-
pleted, the signal will cancel and the lever
will return to its normal position.
Ty p e 2
53M-04-112
Vehicle
Load
ConditionSwitch Position
Alto 800 Alto K10
Petrol CNG Petrol CNG
Driver only0000
Driver + 1
passenger
(in front
seat)0000
Driver + 4
passen-
gers, No
cargo1111
EXAMPLE
Driver + 4
passen-
gers,
Cargo
added2NA3NA
Driver +
Full cargo3NA4NA
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE
EXAMPLE
EXAMPLE