lock SUZUKI ALTO 2013 7.G User Guide

2-12
BEFORE DRIVING
53MH0-74E
Front Seats
Seat AdjustmentAdjusting Seat PositionTy p e 1
53M-04-022
Ty p e 2
53M-04-023
The adjustment lever for each front seat is
located under the front of the seat. To
adjust the seat position, pull up on theadjustment lever and slide the seat forward
or rearward.
After adjustment, try to move the seat for-
ward and rearward to ensure that it is
securely latched.
Adjusting Seatbacks
53MH0209
To adjust the seatback angle of front seats,
pull up the lever on the outboard side of
the seat, move the seatback to the desired
position, and release the lever to lock the
seatback in place.
WARNING
Never attempt to adjust the driver’s
seat or seatback while driving. The
seat or seatback could move unex-
pectedly, causing loss of control.
Make sure that the driver’s seat and
seatback are properly adjusted
before you start driving.
WARNING
To avoid excessive seat belt slack,
which reduces the effectiveness of
the seat belts as a safety device,
make sure that the seats are adjusted
before the seat belts are fastened.EXAMPLE
EXAMPLE
WARNING
All seatbacks should always be in an
upright position when driving, or seat
belt effectiveness may be reduced.
Seat belts are designed to offer maxi-
mum protection when seatbacks are
in the upright position.
EXAMPLE

2-13
BEFORE DRIVING
53MH0-74E
Rear Seats
Folding Rear Seat
The rear seat of your vehicle can be folded
forward to provide additional cargo space.
To fold the rear seat forward:
53MH0211
1) Hook the webbing of the outboard lap-
shoulder belts in the belt hangers.
53MH0212
2) Pull up the release lock knobs on the
top of the seat, and fold the seatback
forward.To return the seat to the normal position,
follow the procedure below.
NOTICE
• When you move a seatback, make
sure the belt webbing is hooked in
the seat belt hangers so the seat
belts are not caught by the seat-
back, seat hinge, or seat latch. This
helps prevent damage to the belt
system.
• Make sure the belt webbing is not
twisted.
EXAMPLENOTICE
After folding the rear seatback for-
ward, do not allow any foreign mate-
rial to enter the lock opening. This
may cause damage to the inside of
the lock and prevent the seatback
from being locked securely.
EXAMPLEWA R N I N G
If you need to carry cargo in the pas-
senger compartment with the rear
seat back folded forward, be sure to
secure the cargo or it may be thrown
about, causing injury. Never pile
cargo higher than the seatback.
WA R N I N G
When returning the rear seatback to
the normal position, make sure that
there is nothing around the striker.
Any foreign materials prevent the
seatback from being locked securely.
CAUTION
When returning the rear seatback to
the normal position, be careful that
your finger is not caught between the
lock and the striker.

2-14
BEFORE DRIVING
53MH0-74E
53MH0213
Raise the seatback until it locks into place.
After returning the seat, try moving the
seatback to make sure they are securely
latched.
Seat Belts and Child Restraint
Systems
65D231S
CAUTION
Do not put your hand into the rear
seatback lock opening, or your finger
may get caught and be injured.
EXAMPLE
NOTICE
• When returning the rear seatback
to the normal position, do not allow
any foreign material to enter the
lock opening. This may prevent the
seatback from being locked
securely.
• When returning the rear seatback
to the normal position, be sure to
handle it carefully by hand to avoid
any damage to the lock itself. Do
not push it by using some material
or by applying excessive force.
• As the lock is designed exclusively
for securing the rear seatback, do
not use it for any other purpose.
Incorrect use of it may cause dam-
age to the inside of the lock and
prevent the seatback from being
locked securely.
WA R N I N G
Wear Your Seat Belts at All Times.
WA R N I N G
An air bag supplements, or adds to,
the frontal crash protection offered
by seat belts. The driver and all pas-
sengers must be properly restrained
by wearing seat belts at all times,
whether or not an air bag is mounted
at their seating position, to minimize
the risk of severe injury or death in
the event of a crash.
EXAMPLE

2-16
BEFORE DRIVING
53MH0-74E
Lap-Shoulder Belt
Emergency Locking Retractor (ELR)
(if equipped)
The seat belt has an emergency locking
retractor (ELR), which is designed to lock
the seat belt only during a sudden stop or
impact. It also may lock if you pull the belt
across your body very quickly. If this hap-
pens, let the belt go back to unlock it, then
pull the belt across your body more slowly.
Safety reminder
60A038
WA R N I N G
(Continued)
• Never use the same seat belt on
more than one occupant and never
attach a seat belt over an infant or
child being held on an occupant’s
lap. Such seat belt use could cause
serious injury in the event of an
accident.
• Periodically inspect seat belt
assemblies for excessive wear and
damage. Seat belts should be
replaced if webbing becomes
frayed, contaminated, or damaged
in any way. It is essential to replace
the entire seat belt assembly after it
has been worn in a severe impact,
even if damage to the assembly is
not obvious.
• Children age 12 and under should
ride properly restrained in the rear
seat.
• Infants and small children should
never be transported unless they
are properly restrained. Restraint
systems for infants and small chil-
dren can be purchased locally and
should be used. Make sure that the
system you purchase meets appli-
cable safety standards. Read and
follow all the directions provided
by the manufacturer.
(Continued)
WA R N I N G
(Continued)
• For children, if the shoulder belt
irritates the neck or face, move the
child closer to the center of the
vehicle.
• Avoid contamination of seat belt
webbing by polishes, oils, chemi-
cals, and particularly battery acid.
Cleaning may safely be carried out
using mild soap and water.
• Do not insert any items such as
coins, clips, etc. into the seat belt
buckles, and be careful not to spill
liquids into these parts. If foreign
materials get into a seat belt
buckle, the seat belt may not work
properly.
• All seatbacks should always be in
an upright position when driving,
or seat belt effectiveness may be
reduced. Seat belts are designed to
offer maximum protection when
seatbacks are in the upright posi-
tion.
Sit up straight and
fully back
Low on hips
EXAMPLE

2-26
BEFORE DRIVING
53MH0-74E
Air bag symbol (if equipped) meaning
57L20203
You may find this label on the sun visor.Please refer to the “Seat Belts and Child
Restraint Systems” section in this section
for details on securing your child.
Door Lock Canceller System
(if equipped)
If SRS Airbag system is activated all doors
are unlocked automatically.
NOTE:
In case door lock wiring and/or motor are
damaged, doors may not unlock automati-
cally.
How the system works
In a frontal collision, the crash sensors will
detect rapid deceleration, and if the con-
troller judges that the deceleration rep-
resents a severe frontal crash, the
controller will trigger the inflators. The infla-
tors inflate the air bags with nitrogen or
argon gas. The inflated air bags provide a
cushion for your head and upper body. The
air bag inflates and deflates so quickly that
you may not even realize that it has acti-vated. The air bag will neither hinder your
view nor make it harder to exit the vehicle.
Air bags must inflate quickly and forcefully
in order to reduce the chance of serious or
fatal injuries. However, an unavoidable
consequence of the quick inflation is that
the air bag may irritate bare skin, such as
the facial area. Also, upon inflation, a loud
noise will occur and some powder and
smoke will be released. These conditions
are not harmful and do not indicate a fire in
the vehicle. Be aware, however, that some
air bag components may be hot for a while
after inflation.
A seat belt helps keep you in the proper
position for maximum protection when an
air bag inflates. Adjust your seat as far
back as possible while still maintaining
control of the vehicle. Sit fully back in your
seat; sit up straight; do not lean over the
steering wheel. Please refer to the “Front
Seat” section and the “Seat Belts and
Child Restraint Systems” section in this
section for details on proper seat and seat
belt adjustments.
WA R N I N G
Do not use a restraint on a seat pro-
tected by an airbag in front of it.
EXAMPLE
WA R N I N G
If the AIR BAG light in the instrument
cluster ever comes on and stays on,
it means that something may be
wrong with the air bag system. If this
ever happens, have the vehicle ser-
viced immediately, because the air
bags may not offer the protection for
which they were designed.

2-27
BEFORE DRIVING
53MH0-74E
53M-04-068
Note that even though your vehicle may be
moderately damaged in a frontal collision,
the collision may not have been severeenough to trigger the air bags to inflate. If
your vehicle sustains ANY front-end dam-
age, have the air bag system inspected by
an MARUTI SUZUKI authorized dealer to
ensure it is in proper working order.
Your vehicle is equipped with a diagnostic
module which records information about
the air bag system if the air bags deploy in
a crash. The module records information
about overall system status, which sensors
activated the deployment, and for a certain
vehicle only, whether the driver’s seat belt
was in use.
Servicing the air bag system
If the air bags inflate, have the air bags and
related components replaced by an autho-
rized MARUTI SUZUKI dealer as soon as
possible.
If your vehicle ever gets in deep water and
the driver’s floor is submerged, the air bag
controller could be damaged. If it does,
have the air bag system inspected by the
MARUTI SUZUKI dealer as soon as possi-
ble.
Special procedures are required for servic-
ing or replacing an air bag. For that reason,
only an authorized MARUTI SUZUKI
dealer should be allowed to service or
replace your air bags. Please remind any-
one who services your MARUTI SUZUKI
that it has air bag.
Service on or around air bag components
or wiring must be performed only by an
MARUTI SUZUKI authorized dealer.
Improper service could result in unin-tended air bag deployment or could render
the air bag inoperative. Either of these two
conditions may result in severe injury.
To prevent damage or unintended inflation
of the air bag system, be sure the battery
is disconnected and the ignition switch has
been in the “LOCK” position for at least 90
seconds before performing any electrical
service work on your MARUTI SUZUKI. Do
not touch air bag system components or
wires. The wires are wrapped with yellow
tape or yellow tubing, and the couplers are
yellow for easy identification.
Scrapping a vehicle that has an uninflated
air bag can be hazardous. Ask your dealer,
body repair shop or scrap yard for help
with disposal.
WA R N I N G
• The driver should not lean over the
steering wheel. In these situations,
the out-of-position occupant would
be too close to an inflating air bag,
and may suffer severe injury.
• Do not attach any objects to, or
place any objects over, the steering
wheel. Do not place any objects
between the air bag and the driver.
These objects may interfere with air
bag operation or may be propelled
by the air bag in the event of a
crash. Either of these conditions
may cause severe injury.
EXAMPLE

2-33
BEFORE DRIVING
53MH0-74E
the light stays on without blinking, then the
engine is overheating. Follow the instruc-
tions in the “If the Engine Overheats” of
“EMERGENCY SERVICE” section.
Immobilizer System Light
53M-04-081
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. If this
light blinks with the ignition switch turned to
“ON”, there may be something wrong with
the immobilizer system. Ask your MARUTI
SUZUKI dealer to have the system
inspected.
Door Lock Canceller Indicator Light
(if equipped)
53M-04-082
This indicator light will come on and keep
blinking continuously if there is some prob-
lem with door lock canceller system. Have
the vehicle inspected by MARUTI SUZUKI
authorized dealer.
NOTE:
In case door lock wiring and/or motor
are
damaged, Door Lock Canceller Indicator
Light will not blink.
Gear Shift Indicator (if equipped)Manual Transaxle
53M-04-083
This indicator informs about upshifting or
downshifting the gear while the vehicle is
running.There are three indications:
Upshift Indicator
This symbol indicates that lower gear posi-
tion is selected for vehicle’s current speed
and / or engine revolution. Changing to
higher gear position is recommended.
Stay Indicator
This symbol indicates that current gear
position is optimal for vehicle’s current
speed and / or engine revolution. No gear
shifting is required.
NOTE:
While driving in optimal gear position, the
upshift/downshift indicator does not
appear.
Downshift Indicator
This symbol indicates that higher gear
position is selected for the vehicle’s current
speed and / or engine revolution. Changing
to lower gear position is recommended.
NOTICE
Continuing to drive the vehicle when
engine overheating is indicated can
result in severe engine damage.

2-36
BEFORE DRIVING
53MH0-74E
When the fuel meter indicator shows only
one segment to “E”, refill the tank as soon
as possible.
NOTE:
• If the last segment blinks, it means that
the fuel is almost empty.
• The fuel meter indicator varies depend-
ing on road conditions (for example,
slope or curve) and driving conditions
because of fuel moving in the tank.
Depress Brake Pedal Indicator
(if equipped)
53M-04-094
Information Display
ALTO 800
53MM02003
53M-04-095
(1) Clock (if equipped)
(2) Odometer/Trip meter
(3) Odometer/Trip meter/Meter illumina-
tion control knob
ALTO K10
Manual transaxle
Without tachometer
53M-04-096
With tachometer
53M-04-097
Automated Manual transaxle
Without tachometer
53M-04-098
(1) (2)(3)
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE

2-37
BEFORE DRIVING
53MH0-74E
With tachometer
53M-04-099
Clock (1) (if equipped)
The clock is shown when the ignition
switch is in the “ON” position.
To set the clock, follow the instructions
below.
Hold in the indication selector and meter
illumination control knob (3) for more
than 2 seconds. Push the indication
selector and meter illumination control
knob (3) to advance the minute display
while the minute display is flashing.
Release the indication selector and
meter illumination control knob (3) for 5
seconds to set the minute display.
The hour display flash after the minute
display is set. Push the indication selec-tor and meter illumination control knob
(3) to advance the hour display. Release
the indication selector and meter illumi-
nation control knob (3) for 5 seconds to
set the hour display.
Odometer/Trip meter (2)
The odometer/trip meter is shown when
the ignition switch is in the “ON” position.
The odometer records the total distance
the vehicle has been driven. The trip meter
can be used to measure the distance trav-
eled on short trips or between fuel stops.
53M-04-100
When the ignition switch is turned to “ON”
with the lighting switch is in the “OFF” posi-
tion, the display shows three types of indi-
cation; odometer (A), trip meter A (B), trip
meter B (C) and clock (D). Push the
“MODE” knob (3) quickly to switch the indi-
cation among the four.
53M-04-101
WA R N I N G
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
Do not attempt to adjust the display
while driving.
EXAMPLE
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
EXAMPLE
EXAMPLE

2-38
BEFORE DRIVING
53MH0-74E
When the ignition switch is turned to “ON”
and the position lights, tail lights and/or the
headlights are on, the display shows four
types of indication; odometer (A), trip
meter A (B), trip meter B (C), clock (D) and
indication of illumination intensity (E). Push
the “MODE” knob (3) quickly to switch the
indication among the five. When the indica-
tion shows (E), you can control the meter
illumination intensity. Refer to “Meter illumi-
nation control” section below for details on
how to dim or brighten the meter illumina-
tion.
53M-04-102
To reset the trip meter to zero, hold in the
“MODE” knob (3) for about 2 seconds.Meter illumination control
53M-04-103
When the display shows the indication of
illumination intensity (E), you can dim or
brighten the meter illumination.
To change the meter illumination bright-
ness, continue to hold in the “MODE” knob
(3). The indication will change as shown in
the illustration. The illumination gets dim-
mer then returns to the brightest condition
after it reaches the dimmest.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the brightness of the
instrument panel lights will be reinitialized.
Readjust the brightness according to your
preference.
Lighting Control Lever
53M-04-104EXAMPLE
EXAMPLE
EXAMPLE
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE