maintenance SUZUKI ALTO 2013 7.G User Guide

4-5
DRIVING TIPS
53MH0-74E
If Your Vehicle Gets Stuck
If your vehicle gets stuck in snow, mud, or
sand, follow the directions below:
1) Shift the transaxle back and forth
between a forward range (or first gear
for manual transaxle) and reverse. This
will create a rocking motion which may
give you enough momentum to free the
vehicle. Press gently on the accelerator
to keep wheel spinning to a minimum
wheel rpm. Remove your foot from the
accelerator while shifting. Do not race
the engine. Excessive wheel spin will
cause the tires to dig deeper, making it
more difficult to free the vehicle.
2) If your vehicle remains stuck after a few
minutes of rocking, we recommend you
to consult your authorised Maruti
Suzuki workshop or a roadside assis-
tance service. If a towing service is not
available in an emergency, your vehicle
may be temporarily towed by a towing
cable or chain secured to the towing
hook either on the front of the vehicle or
on the rear of the vehicle. Refer to
“Frame Hooks” in the “OTHER CON-
TROLS AND EQUIPMENT” section.
Driving On Wet Roads
WA R N I N G
Do not allow anyone to stand near
the vehicle when you are rocking it,
and do not spin the wheels faster
than an indicated 40 km/h on the
speedometer. Personal injury and/ or
vehicle damage may result from spin-
ning the wheels too fast.
NOTICE
Do not continue rocking the vehicle
for more than a few minutes. Pro-
longed rocking can cause engine
overheating or transaxle damage.
CAUTION
• When driving on wet roads, avoid
driving through large amount of
standing water on the road. Large
amount of water entering the
engine compartment may cause
damage to the engine and or elec-
trical components.
• If stuck in deep water, do not start
till water level drops.
• Water is incompressible substance,
water inside engine is harmful to
the engine.
WA R N I N G
• In addition to following the driving
tips in this section, it is important
to observe the following precau-
tions.
• Make sure your tires are in good
condition and always maintain the
specified tire pressure. Refer to
“Tires” in the “INSPECTION AND
MAINTENANCE”
• Do not use tires other than those
specified by MARUTI SUZUKI.
Never use different sizes or types
of tires on the front and rear
wheels. For information regarding
the specified tires, refer to the Tire
Information Label located on the
driver’s door lock pillar.
• Never use oversized tires or spe-
cial shock absorbers and springs
to raise (jack up) your vehicle. This
will change the handling character-
istics. Oversized tires may also rub
against the vehicle body over
bumps, causing vehicle damage or
tire failure.
•After driving through water, test the
brakes while driving at a slow
speed to see if they have main-
tained their normal effectiveness. If
the brakes are less effective than
normal, dry them by repeatedly
applying the brakes while driving
slowly until the brakes have
regained their normal effective-
ness
.

5-5
OTHER CONTROLS AND EQUIPMENT
53MH0-74E
tion, an indicator light will come on when
the air conditioning system is on. To turn
off the air conditioning system, push the
“A/C” switch again.
• During operation of the air conditioner,
you may notice slight changes in engine
speed. These changes are normal, the
system is designed so that the compres-
sor turns on or off to maintain the
desired temperature. Less operation of
the compressor results in better fuel
economy.
NOTE:
• If you select RECIRCULATED AIR for an
extended period of time, the air in the
vehicle can become contaminated.
Therefore, you should occasionally
select FRESH AIR.
• If your vehicle has been left in the sun
with the windows closed, it will cool
faster if you open the windows briefly
while you operate the air conditioner with
the air intake selector at FRESH AIR and
the blower at high speed.
Dehumidifying
Set the air flow selector to a desired air
flow selector position, the temperature
selector to the desired temperature posi-
tion and the blower speed selector to the
desired blower speed position. Also select
FRESH AIR and turn on the “A/C” switch.NOTE:
Because the air conditioner dehumidifies
the air, turning it on will help keep the win-
dows clear, even when blowing heated air
using the DEFROST or HEAT &
DEFROST functions.
53MH0511
NOTE:
If you need maximum defrosting:
• set the air flow selector to DEFROST,
• set the blower speed selector to high,
• adjust the temperature selector to the
hot end, and
• adjust the side outlets so the air blows
on the side windows.
Maintenance
If you do not use the air conditioner for a
long period, such as during winter, it may
not give the best performance when you
start using it again. To help maintain opti-
mum performance and durability of your air
conditioner, it needs to be run periodically.
Operate the air conditioner at least once a
month for one minute with the engine
idling. This circulates the refrigerant and oil
and helps protect the internal components.
NOTE:
Your vehicle uses the air conditioning
refrigerant HFC-134a, commonly called
“R-134a”. R-134a replaced R-12 around
1993 for automotive applications. Other
refrigerants are available, including recy-
cled R-12, but only R-134a should be used
in your vehicle.
EXAMPLE
NOTICE
Using the wrong refrigerant may
damage your air conditioning sys-
tem. Use R-134a only. Do not mix or
replace the R-134a with other refrig-
erants.

INSPECTION AND MAINTENANCE
7
53MH0-74E
INSPECTION AND MAINTENANCE
Maintenance Schedule ....................................................... 7-2
Periodic Maintenance Schedule ........................................ 7-2
Drive Belt ............................................................................. 7-10
Engine Oil and Filter ........................................................... 7-10
Engine Coolant .................................................................... 7-13
Air Cleaner ........................................................................... 7-15
Spark Plugs ......................................................................... 7-15
Gear Oil ................................................................................ 7-16
Clutch Pedal ........................................................................ 7-17
Fuel Filter ............................................................................. 7-17
Brakes .................................................................................. 7-18
Steering ................................................................................ 7-20
Tires ...................................................................................... 7-20
Battery .................................................................................. 7-22
Fuses .................................................................................... 7-23
Bulb Replacement ............................................................... 7-27
Wiper Blades ....................................................................... 7-29
Windshield Washer Fluid ................................................... 7-31
Air Conditioning System .................................................... 7-31

7-1
INSPECTION AND MAINTENANCE
53MH0-74E
60A187S
WA R N I N G
You should take extreme care when
working on your vehicle to prevent
accidental injury. Here are a few pre-
cautions that you should be espe-
cially careful to observe:
(Continued)
WA R N I N G
(Continued)
• To prevent damage or unintended
activation of the air bag system or
seat belt pretensioner system, be
sure the battery is disconnected
and the ignition switch has been in
the “LOCK” position for at least 90
seconds before performing any
electrical service work on your
vehicle. Do not touch air bag sys-
tem components, seat belt preten-
sioner system components or
wires.
The wires are wrapped with yellow
tape or yellow tubing, and the cou-
plers are yellow for easy identifica-
tion.
• Do not leave the engine running in
garages or other confined areas.
• When the engine is running, keep
hands, clothing, tools, and other
objects away from the fan and drive
belt. Even though the fan may not
be moving, it can automatically
turn on without warning.
(Continued)
WA R N I N G
(Continued)
• When it is necessary to do service
work with the engine running, make
sure that the parking brake is set
fully and the transaxle is in Neutral.
• Do not touch ignition wires or other
ignition system parts when start-
ing the engine or when the engine
is running, or you could receive an
electric shock.
• Be careful not to touch a hot
engine, exhaust manifold and
pipes, muffler, radiator and water
hoses.
• Do not allow smoking, sparks, or
flames around fuel or the battery.
Flammable fumes are present.
• Do not get under your vehicle if it is
supported only with the portable
jack provided in your vehicle.
• Be careful not to cause accidental
short circuits between the positive
and negative battery terminals.
• Keep used oil, coolant, and other
fluids away from children and pets.
Dispose of used fluids properly;
never pour them on the ground,
into sewers, etc.

7-2
INSPECTION AND MAINTENANCE
53MH0-74E
Maintenance Schedule
The following table shows when regular
maintenance on your vehicle is required,
this table shows in kilometers and months
when inspections, adjustments, lubrication
and other services should be performed.

Periodic Maintenance
Schedule
ALTO 800
“A”: Adjust
“C”: Clean
“R”: Replace or Change
“I” : Inspect, clean, adjust, lubricate or
replace as necessary
“L” : Lubricate
“T” : Tighten to Specified Torque
“O”: Rotate
NOTE:
This table includes services as scheduled
up to 80,000 km mileage. Beyond 80,000
km, carry out the same services at the
same intervals respectively.
WA R N I N G
MARUTI SUZUKI recommends that
maintenance on your MARUTI
SUZUKI vehicle be performed by
MARUTI SUZUKI Authorised Dealer/
Service Station.
CAUTION
Whenever it becomes necessary to
replace parts on your vehicle, it is
recommended that you use MARUTI
GENUINE PARTS (MGP).

7-3
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ENGINE
1.Water pump drive belt (Tension, Wear) AIIIIIIRAI
2. Engine Coolant (Level, Leakage) I I I R I R I R I R
3.Engine oil and Oil filter R I RRRRRRRR
4. Cooling system hoses and connections (Leakage, Damage) I I IIIIIIII
5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –
6. Engine mounting (Loose, Damage) – – T – T – T – T –
7. Valve Clearance – A – A – A – A – A
8. Camshaft timing belt (Damage, Wear)–––I–I–I–I
Replace Every 1,00,000 km
9. Exhaust system (Noise, Leakage etc.) – I – I – I – I – I
10. Positive crankcase ventilation System (Hoses, Connections and Valve) – I – I – I – I – I
IGNITION
1. Ignition wiring (Damage, Deterioration) – – – I – I – I – I
2. Spark plugs (Clean and Adjust the gap) – – I R I R I R I R
FUEL
1. Air cleanerPaved-road Clean every 5,000 km. Replace after every 40,000 km.
Dusty condition Clean every 2,500 km or as required. Replace after every 40,000 km.
More frequent replacement if dust condition is severe.
2. Fuel tank cap, fuel lines and connections (Leakage, Damage) – I – – – I – – – I
3. Fuel filter (Leakage) I I I I I R I I I R
CLUTCH AND TRANMISSION
1. Clutch pedal (Play) I I IIIIIIII
2. Clutch slipping (Dragging or Excessive damage) I I IIIIIIII
3. Manual Transmission Oil (Level, Leakage)IIIIIIIIII
Replace every 1,60,000 kms or 10 years, which ever comes earlier
DRIVE SHAFTS
1. Drive shafts boot (Boot cut / Damage) – I IIIIIIII
2.Drive Shaft Noise IIIIIIIIII

7-4
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2.Brake pedal (Pedal-to-wall clearance) IIIIIIIIII
3.Parking brake lever and cable (Play, Damage) IIIIIIIIII
4.a. Brake discs and pads (Wear) – I IIIIIIII
b. Brake drums & shoes (Wear) – – IIIIIIII
5.Master cylinder, wheel cylinder, caliper piston (Fluid leakage, Boot/Seal
Damage)IIIIIIIIII
6.Brake hoses and pipes (Fluid leakage, Damage)
IIIIIIIIII
WHEEL
1. Tyres (Air pressure, Abnormal wear, Crack, Rotation) I
I&OI&O I&OI&OI&OI&OI&OI&O I&O
2. Wheels (Damage) I
I I I I I I I I I
3. Front/Rear wheel bearings (Loose, Damage) –
I I I I I I I I I
FRONT AND REAR SUSPENSION
1. Suspension strut (Oil leakage, Damage) I
I I I I I I I I I
2. Suspension arms/knuckle support (Loose, Damage) –
IIIIII I I I
3. Rear spring (Damage) –
I I I I I I I I I
4. Shock absorbers (Oil leakage, Damage) I
I I I I I I I I I
5. All bolts and nuts (Loose)–
T T T T T T T T T
6. Suspension arms and Tension rods –
I I I I I I I I I
STEERING
1. Steering wheel (Play, Loose) I
I I I I I I I I I
2. All rods and arms (Loose, Damage, Wear) I
I I I I I I I I I
ELECTRICAL
1. Battery electrolyte (Level, leakage) I
I I I I I I I I I
2. Wiring harness connection (Loose, Damage) –
I I I I I I I I I
3. Lighting system (Operation, Stains, Damage) I
I I I I I I I I I
4. Horn (Operation) I
I I I I I I I I I
5. System voltage I
I I I I I I I I I
BODY
1. All chassis bolts and nuts (Tighten)
–II T
T T T T T T
2. All latches, hinges and locks (Function)
II&LI&L I&L
I&L I&L I&L I&L I&L I&L

7-5
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ROAD TEST
1. Operation of Brakes, Gear shifting and speedometer
II I I
I I I I I I
2.Body and Chassis noise
II I I
I I I I I I
AIR CONDITIONER (if equipped)
1. Check belt tension
IIII
IIIIII
3. Tighten compressor mounting bolts
–TTT
TTTTTT
2. All hose joints (Check, Tighten)
IIII
I I I I I I
4. Check functioning of Recirculating flap
IIII
I II I I I
5.Clean condenser with low pressure water
–CCCCCCCCC
6. Check belt for frayed edges, change if necessary
–I I I
I II I I I
7.Check all mounting bolts
–I I I
I I I I I I

7-6
INSPECTION AND MAINTENANCE
53MH0-74E
Periodic Maintenance
Schedule
ALTO K10
“A”: Adjust
“C”: Clean
“R”: Replace or Change
“I” : Inspect, clean, adjust, lubricate or
replace as necessary
“L” : Lubricate
“T” : Tighten to Specified Torque
“O”: Rotate
NOTE:
This table includes services as scheduled
up to 80,000 km mileage. Beyond 80,000
km, carry out the same services at the
same intervals respectively.

7-7
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ENGINE
1.Water pump drive belt (Tension, Wear) ––––– I ––– I
2. Engine Coolant (Level, Leakage) I I I R I R I R I R
3. Engine oil and Oil filter – – RRRRRRRR
4. Cooling system hoses and connections (Leakage, Damage)IIIIIIIIII
5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –
6. Engine Mounting (Loose, Damage) – – T – T – T – T –
7.Valve Clearance –––– I –– I ––
8. Exhaust System (Noise, Leakage etc.) – I – I – I – I – I
9. Positive crankcase ventilation System (Hoses, Connections and Valve) – I – I – I – I – I
IGNITION
1. Ignition wiring (Damage, Deterioration) – – – I – I – I – I
2.Spark plugs –––––R–––R
FUEL
1. Air cleanerPaved-road Clean every 5,000 km. Replace after every 40,000 km.
Dusty condition Clean every 2,500 km or as required. Replace after every 40,000 km.
More frequent replacement if dust condition is severe.
2. Fuel tank cap, fuel lines and connections (Leakage, Damage) – I – – – I – – – I
3. Fuel filter (Leakage) – I I I I R I I I R
CLUTCH AND TRANMISSION
1.Clutch pedal (Play) IIIIIIIIII
2.Clutch slipping (Dragging or Excessive damage) IIIIIIIIII
3. Manual Transmission Oil (Level, Leakage)IIIIIIIIII
Replace every 1,60,000 kms or 10 years whichever comes first
DRIVE SHAFTS
1. Drive shaft boots (Boot cut / Damage)IIIIIIIIII
2.Drive Shaft Noise IIIIIIIIII
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2. Brake pedal (Pedal-to-wall clearance)IIIIIIIIII