battery SUZUKI ALTO 2013 7.G Owners Manual

2-5
BEFORE DRIVING
53MH0-74E
Keyless Entry System (if
equipped)
53M-04-010
Keyless EntryYou can lock / unlock all doors simultane-
ously by operating the transmitter near the
vehicle.
To lock all doors, press “LOCK” button
once. All indicator lights will flash once
when doors are locked.
To unlock all doors, press “UNLOCK”
button once. All indicator lights will flash
twice when doors are unlocked.
NOTE:
• The operating distance of the keyless
entry system transmitter is about 20
meters, but this may vary depending on
the condition of transmitter’s battery and
surroundings especially near other
transmitting devices such as radio tow-
ers.
• The door locks cannot be operated with
the transmitter if the ignition key is
inserted in the key cylinder or if any door
is open.
• Be sure to close the doors and windows
before locking.• If you lose any of the transmitters (keys),
contact your MARUTI SUZUKI autho-
rised dealer as soon as possible for
erasing the transmitter ID from vehicle
controller memory. In case you need a
new transmitter, place an order with your
dealer.
• Key cylinder mentioned in this section is
the key hole mounted on steering col-
umn, where key is inserted to start the
vehicle.
GENERAL FEATURES
Illuminated Entry
When vehicle is unlocked, the room lamp
will turn ON to facilitate illuminated entry
into the vehicle. The room lamp will turn
OFF when the door is closed.
Illuminated Exit
When door is opened to exit the vehicle,
the room lamp will turn ON and will turn
OFF when the door is closed.
Auto Relock
In case of accidental Unlock/Disarm of
vehicle by Key, vehicle will automatically
Lock within 30 sec. without any indication.
Auto relock cycle gets canceled if user
does any of the following operation within
30 sec:
1. Open any door.
2. Insert key in cylinder.
3. Any door is locked/unlocked by door
knob.
Radio Frequency Lock Out
Key Lock/Unlock/Panic will cease to func-
tion when Key is inside Key cylinder.
EXAMPLE
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
the transmitter:
• Do not expose it to impacts, mois-
ture, dust or high temperature such
as leaving it on the dashboard
under direct sunlight.
• Do not tamper with internal parts.
• Keep the transmitter away from
magnetic objects such as a televi-
sion.

2-8
BEFORE DRIVING
53MH0-74E
Transmitter battery
Replacement of the Battery
53M-04-013
If the transmitter battery gets discharged, replace the battery with a new one. To replace the battery of the transmitter: 1) Remove the screw (1), and open thetransmitter cover. 2) Remove the tr ansmitter (2). 3) Put the edge of a flat blade screw driverin the slot of the transmitter (2) and pry it open. 4) Replace the battery (3) (Lithium disctype CR1620) so that its +ve terminal faces the bottom cover of the transmit- ter (5).
53M-04-014
5) Close the transmitter and install it into the transmitter holder. 6) Close the transmitte r cover, install and tighten the screw (1). 7) Make sure the door locks can be oper- ated with the transmitter.
NOTE: Normal battery life is approximately 2years, but varies depending on usage. It is advisable to get battery replaced from MARUTI SUZUKI Authorized workshop.
53M-04-015
EXAMPLE
CAUTION
Do not remove the screw from thekey unnecessarily as it damages thescrew head. Kindly replace the screw once the transmitter battery is changed.
EXAMPLE
CAUTION
Dispose off the used battery properly according to applicable rules or regu- lations. Do not di spose off lithium batteries with ordinary household trash.
WA R N I N G
Swallowing a lithium battery may cause serious internal injury. Do not allow anyone to swallow a lithium battery. Keep lithium batteries away from chil-dren and pets. If sw allowed, contact a physician immediately.

2-9
BEFORE DRIVING
53MH0-74E TROUBLESHOOTING

SYMPTOMS PROBABLE CAUSES REMEDIES
Transmitter function (Unlock/Lock/Car
Locator) not working 1) Battery of the transmitter is weak.
2) Transmitter is exposed to water or it is
wet.
3) D/L or Dome fuse for controller is blown
in the vehicle.
4) In case if any door is open or door sen-
sor is shorted with the body ground,
remote will not activate the central lock-
ing.1) Check the battery.
2) Dry the transmitter and check it.
3) Check and replace the D/L or Dome
fuse.
4) Check if all doors are properly closed
and door switch functioning is O.K.
Operation distance of the transmitter is
less than 20m but still transmitter (Unlock/
Lock/Car Locator) is not working 1) Battery of the transmitter is weak.
2) Strong RF interference. (e.g. Radio
Towers, High Voltage Transmission line
near by)1) Check the battery.
2) Drive the vehicle away from the particu-
lar spot and re-test the control distance.
It is difficult to activate or deactivate the
system in certain area using the
transmitter. 1) The strong interference caused by
excessive RF activity in a particular
area1) The interference is temporary and only
while the vehicle is in that area.

2-16
BEFORE DRIVING
53MH0-74E
Lap-Shoulder Belt
Emergency Locking Retractor (ELR)
(if equipped)
The seat belt has an emergency locking
retractor (ELR), which is designed to lock
the seat belt only during a sudden stop or
impact. It also may lock if you pull the belt
across your body very quickly. If this hap-
pens, let the belt go back to unlock it, then
pull the belt across your body more slowly.
Safety reminder
60A038
WA R N I N G
(Continued)
• Never use the same seat belt on
more than one occupant and never
attach a seat belt over an infant or
child being held on an occupant’s
lap. Such seat belt use could cause
serious injury in the event of an
accident.
• Periodically inspect seat belt
assemblies for excessive wear and
damage. Seat belts should be
replaced if webbing becomes
frayed, contaminated, or damaged
in any way. It is essential to replace
the entire seat belt assembly after it
has been worn in a severe impact,
even if damage to the assembly is
not obvious.
• Children age 12 and under should
ride properly restrained in the rear
seat.
• Infants and small children should
never be transported unless they
are properly restrained. Restraint
systems for infants and small chil-
dren can be purchased locally and
should be used. Make sure that the
system you purchase meets appli-
cable safety standards. Read and
follow all the directions provided
by the manufacturer.
(Continued)
WA R N I N G
(Continued)
• For children, if the shoulder belt
irritates the neck or face, move the
child closer to the center of the
vehicle.
• Avoid contamination of seat belt
webbing by polishes, oils, chemi-
cals, and particularly battery acid.
Cleaning may safely be carried out
using mild soap and water.
• Do not insert any items such as
coins, clips, etc. into the seat belt
buckles, and be careful not to spill
liquids into these parts. If foreign
materials get into a seat belt
buckle, the seat belt may not work
properly.
• All seatbacks should always be in
an upright position when driving,
or seat belt effectiveness may be
reduced. Seat belts are designed to
offer maximum protection when
seatbacks are in the upright posi-
tion.
Sit up straight and
fully back
Low on hips
EXAMPLE

2-27
BEFORE DRIVING
53MH0-74E
53M-04-068
Note that even though your vehicle may be
moderately damaged in a frontal collision,
the collision may not have been severeenough to trigger the air bags to inflate. If
your vehicle sustains ANY front-end dam-
age, have the air bag system inspected by
an MARUTI SUZUKI authorized dealer to
ensure it is in proper working order.
Your vehicle is equipped with a diagnostic
module which records information about
the air bag system if the air bags deploy in
a crash. The module records information
about overall system status, which sensors
activated the deployment, and for a certain
vehicle only, whether the driver’s seat belt
was in use.
Servicing the air bag system
If the air bags inflate, have the air bags and
related components replaced by an autho-
rized MARUTI SUZUKI dealer as soon as
possible.
If your vehicle ever gets in deep water and
the driver’s floor is submerged, the air bag
controller could be damaged. If it does,
have the air bag system inspected by the
MARUTI SUZUKI dealer as soon as possi-
ble.
Special procedures are required for servic-
ing or replacing an air bag. For that reason,
only an authorized MARUTI SUZUKI
dealer should be allowed to service or
replace your air bags. Please remind any-
one who services your MARUTI SUZUKI
that it has air bag.
Service on or around air bag components
or wiring must be performed only by an
MARUTI SUZUKI authorized dealer.
Improper service could result in unin-tended air bag deployment or could render
the air bag inoperative. Either of these two
conditions may result in severe injury.
To prevent damage or unintended inflation
of the air bag system, be sure the battery
is disconnected and the ignition switch has
been in the “LOCK” position for at least 90
seconds before performing any electrical
service work on your MARUTI SUZUKI. Do
not touch air bag system components or
wires. The wires are wrapped with yellow
tape or yellow tubing, and the couplers are
yellow for easy identification.
Scrapping a vehicle that has an uninflated
air bag can be hazardous. Ask your dealer,
body repair shop or scrap yard for help
with disposal.
WA R N I N G
• The driver should not lean over the
steering wheel. In these situations,
the out-of-position occupant would
be too close to an inflating air bag,
and may suffer severe injury.
• Do not attach any objects to, or
place any objects over, the steering
wheel. Do not place any objects
between the air bag and the driver.
These objects may interfere with air
bag operation or may be propelled
by the air bag in the event of a
crash. Either of these conditions
may cause severe injury.
EXAMPLE

2-32
BEFORE DRIVING
53MH0-74E
Electric Power Steering Light
(if equipped)
53M-04-077
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started.
If this light comes on while driving, the
power steering system may not work prop-
erly. Have the system inspected by your
MARUTI SUZUKI dealer.
NOTE:
If the power steering system does not work
properly, you will feel heavier to steer but
you still will be able to steer.
Oil Pressure Light
53M-04-078
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. Thelight will come on and remain on if there is
insufficient oil pressure. If the light comes
on when driving, pull off the road as soon
as you can and stop the engine.
Check the oil level and add oil if necessary.
If there is enough oil, the lubrication sys-
tem should be inspected by your MARUTI
SUZUKI dealer before you drive the vehi-
cle again.
Charging Light
53M-04-079
This light comes on when the ignition
switch is turned to the “ON” position, and
goes out when the engine is started. The
light will come on and remain on if there is
something wrong with the battery charging
system. If the light comes on when the
engine is running, the charging system
should be inspected immediately by your
MARUTI SUZUKI dealer.
High Engine Coolant Temperature
Warning Light
53M-04-080
When the ignition switch is turned to the
“ON” position, this light comes on briefly so
you can check that the light is working. If
this light blinks while driving, it means the
engine is running hot. Avoid driving condi-
tions that may lead to actual overheating. If
NOTICE
• If you operate the engine with this
light on, severe engine damage can
result.
• Do not rely on the Oil Pressure
Light to indicate the need to add
oil. Be sure to periodically check
the engine oil level.

2-38
BEFORE DRIVING
53MH0-74E
When the ignition switch is turned to “ON”
and the position lights, tail lights and/or the
headlights are on, the display shows four
types of indication; odometer (A), trip
meter A (B), trip meter B (C), clock (D) and
indication of illumination intensity (E). Push
the “MODE” knob (3) quickly to switch the
indication among the five. When the indica-
tion shows (E), you can control the meter
illumination intensity. Refer to “Meter illumi-
nation control” section below for details on
how to dim or brighten the meter illumina-
tion.
53M-04-102
To reset the trip meter to zero, hold in the
“MODE” knob (3) for about 2 seconds.Meter illumination control
53M-04-103
When the display shows the indication of
illumination intensity (E), you can dim or
brighten the meter illumination.
To change the meter illumination bright-
ness, continue to hold in the “MODE” knob
(3). The indication will change as shown in
the illustration. The illumination gets dim-
mer then returns to the brightest condition
after it reaches the dimmest.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the brightness of the
instrument panel lights will be reinitialized.
Readjust the brightness according to your
preference.
Lighting Control Lever
53M-04-104EXAMPLE
EXAMPLE
EXAMPLE
WA R N I N G
To avoid possible injury, do not oper-
ate controls by reaching through the
steering wheel.
EXAMPLE

3-2
OPERATING YOUR VEHICLE
53MH0-74E
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint
(if equipped).
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened your seat belts.
10)Make sure that all warning lights come
on as the key is turned to the “ON” posi-
tion.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the
parking brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Windshield washer fluid level
5) Battery solution level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See “Alllatches, hinges & locks” of “CHASSIS
AND BODY” in the “Periodic Mainte-
nance Schedule” in the “INSPECTION
AND MAINTENANCE” section for lubri-
cation schedule.
Once a month, or each time you fill your
fuel tank, check the tire pressure using a
tire pressure gauge. Also check the tire
pressure of the spare tire.Engine Oil Consumption
It is normal for the engine to consume
some engine oil during normal vehicle
operation.
The amount of engine oil consumed
depends on the viscosity of the oil, the
quality of the oil and the conditions the
vehicle is driven under.
More oil is consumed during high-speed
driving and when there is frequent acceler-
ation and deceleration. Under high loads,
your engine also will consume more oil.
A new engine also consumes more oil,
since its pistons, piston rings and cylinder
walls have not yet become conditioned.
New engines reach the normal level of oil
consumption only after approximately 5000
km (3000 miles) driving.
Oil consumption:
Max. 1.0 L per 1000 km
When judging the amount of oil consump-
tion, note that the oil may become diluted
and make it difficult to accurately judge the
true oil level.
As an example, if a vehicle is used for
repeated short trips, and consumes a nor-
mal amount of oil, the dipstick may not
show any drop in the oil level at all, even
after 1000 km or more of driving. This is
because the oil is gradually becoming
diluted with fuel or moisture, making it
appear that the oil level has not changed.
WA R N I N G
Make sure the hood is fully closed
and latched before driving. If it is not,
it can fly up unexpectedly during
driving, obstructing your view and
resulting in an accident.

3-4
OPERATING YOUR VEHICLE
53MH0-74E
It locks the ignition, and prevents normal
use of the steering wheel after the key is
removed.
To release the steering lock, insert the key
and turn it clockwise to one of the other
positions. If you have trouble turning the
key to unlock the steering, try turning the
steering wheel slightly to the right or left
while turning the key.
ACC
Accessories such as the radio can oper-
ate, but the engine is off.
ON
This is the normal operating position. All
electrical systems are on.
START
This is the position for starting the engine
using the starter motor. The key should be
released from this position as soon as the
engine starts.
Ignition key reminder (if equipped)
A buzzer sounds intermittently to remind
you to remove the ignition key if it is in the
ignition switch when the driver’s door is
opened.
81A297S
WA R N I N G
• Never remove the ignition key
while the vehicle is moving. The
steering wheel will lock and you
will not be able to steer the vehicle.
• Always remove the ignition key
when leaving the vehicle even if
only for a short time. Also do not
leave children alone in a parked
vehicle. Unattended children could
cause accidental movement of the
vehicle or could tamper with power
windows. They also could suffer
from heat stroke in warm or hot
weather. These could result in
severe injury or even death.
EXAMPLENOTICE
• Do not use the starter motor for
more than 15 seconds at a time. If
the engine does not start, wait 15
seconds before trying again. If the
engine does not start after several
attempts, check the fuel and igni-
tion systems or consult your MAR-
UTI SUZUKI dealer.
• Do not leave the ignition switch in
the “ON” position if the engine is
not running as the battery will dis-
charge.

INSPECTION AND MAINTENANCE
7
53MH0-74E
INSPECTION AND MAINTENANCE
Maintenance Schedule ....................................................... 7-2
Periodic Maintenance Schedule ........................................ 7-2
Drive Belt ............................................................................. 7-10
Engine Oil and Filter ........................................................... 7-10
Engine Coolant .................................................................... 7-13
Air Cleaner ........................................................................... 7-15
Spark Plugs ......................................................................... 7-15
Gear Oil ................................................................................ 7-16
Clutch Pedal ........................................................................ 7-17
Fuel Filter ............................................................................. 7-17
Brakes .................................................................................. 7-18
Steering ................................................................................ 7-20
Tires ...................................................................................... 7-20
Battery .................................................................................. 7-22
Fuses .................................................................................... 7-23
Bulb Replacement ............................................................... 7-27
Wiper Blades ....................................................................... 7-29
Windshield Washer Fluid ................................................... 7-31
Air Conditioning System .................................................... 7-31