brake SUZUKI ALTO 2013 7.G Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2013, Model line: ALTO, Model: SUZUKI ALTO 2013 7.GPages: 190, PDF Size: 8.76 MB
Page 11 of 190
0-3
82PH0-74E
WARRANTY POLICY
Maruti Suzuki India Limited (hereinafter called “Maruti Suzuki”),
warrants that each new Maruti Suzuki vehicle distributed in India
by Maruti Suzuki and sold by an authorised Maruti Suzuki dealer
will be free, under normal use and service, from any defects in
material and workmanship at the time of manufacture SUBJECT
TO THE FOLLOWING TERMS AND CONDITIONS:
(1) Qualification:To qualify for this warranty the vehicle must be delivered by a
Maruti Suzuki authorised dealer and set-up, and serviced by a
Maruti Suzuki authorised dealer / service station.
(2) Term:The term of the warranty shall be twenty-four (24) months or
40,000 kilometers (whichever occurs first) from the date of
invoice to the first owner.
(3) Maruti Suzuki Warranty Obligation:If any defect(s) should be found in a Maruti Suzuki vehicle within
the term stipulated above, Maruti Suzuki’s only obligation is to
repair or replace at its sole discretion any part shown to be defec-
tive, with a new part or the equivalent at no cost to the owner for
parts or labour, when Maruti Suzuki acknowledges that such a
defect is attributable to faulty material or workmanship at the time
of manufacture. The owner is responsible for any repair or replace-
ments which are not covered by this warranty.
(4) Limitation:
This warranty shall not apply to:
(a) Normal maintenance service required other than the three
free services, including without limitation, oil and fluid
changes, headlight aiming, fastener retightening, wheel bal-
ancing, wheel alignment and tyre rotation, cleaning of injec-
tors, adjustments of clutch and valve clearance.
(b) The replacement of normal wear parts including without lim-
itation, bulbs, tyres and tubes, spark plugs, belts, hoses, fil-
ters, wiper blades, brushes, contact points, fuses, clutch
disc, brake shoes, brake pads, cable and all rubber parts
(except oil seal and glass run).
(c) Any vehicle which has been used for competition or racing.
(d) Any repairs or replacement required as a result of accidents
or collision.
(e) Any defects caused by misuse, negligence, abnormal use or
insufficient care.
(f) Any vehicle which has been modified or altered, including
without limitation, the installation of performance accesso-
ries.
(g) Any vehicle on which parts or accessories not approved by
Maruti Suzuki have been used.
(h) Any vehicle which has not been operated in accordance with
the operating instructions in this Owner’s Manual and Ser-
vice Booklet.
(i) Any vehicle which has not received, during the warranty term,
the service inspections prescribed in this Owner’s Manual
and Service Booklet.
(j) Any vehicle which has been assembled, disassembled,
adjusted or repaired by other than an Maruti Suzuki autho-
rised dealer/service station.
(k) Any vehicle which has been used for purposes other than
what it was designed for.
(l) Any damage or deterioration caused by industrial pollution
and bird droppings.
Page 13 of 190
0-5
82PH0-74E
EMISSION WARRANTY POLICY
Maruti Suzuki offers the Emission Warranty on all Maruti Suzuki
vehicles (apart from the Regular Warranty and will run parallel to
the regular product warranty) only in four metropolitan cities (New
Delhi, Kolkata, Mumbai and Chennai) with effect from July 1st,
2001.
Terms:The Emission Warranty will be applicable for 80,000 kms or 3
years (Whichever comes earlier) from the date of invoice to the
first owner. The remaining warranty terms will be valid in case of
any change in ownership provided the production of all valid docu-
ments.
Conditions:1. Under Emission Warranty, Warranty claims will be admitted for
a prima facie examination, in case vehicle fails to meet the
Emission Standard as specified in sub rule (2) of rule no. 115
of Central Motor Vehicles Rules (CMVR), 1989.
2. The warranty claims will only be accepted after examination
carried out by Maruti Suzuki or it’s dealer which leads to firm
conclusions that the
a) Original settings have not been tampered in any case.
b) Part (as given in Annexure - A) has a manufacturing defect.
c) Vehicle is unable to meet the Emission Standards (as given
in 1.), inspite of the vehicle having been maintained and
used in accordance with the instructions as specified in
Owner’s Manual and Service Booklet and the used fuel and
different oils (Engine oil, Transmission oil, Brake oil etc.) are
also as per specification. 3. The method of examination for deciding the warranty of the
parts will be at the sole discretion of Maruti Suzuki and it’s
dealer and results of the examination will be final and binding.
If after examination, the warrantable condition is not estab-
lished, Maruti Suzuki and it’s dealer has the right to charge all,
or part of the cost of such examination.
4. Under Emission Warranty, the parts (as given in Annexure - A)
will be changed free of cost, but the consumables will be
charged as per actual.
5. If the part covered under Emission Warranty or the associated
parts, are not independently replaceable, on account of these
being integral parts of a complete assembly, Maruti Suzuki and
it’s dealer will have the sole discretion to replace either the
entire assembly or by using some of the parts of the system
through suitable repairs or modifications.
6. Any consequential repairs or replacement of parts which may
be found necessary to establish compliance of Emission War-
ranty, will not be considered under warranty, unless the same is
under product warranty. The consumable will be charged as
per actual under such repair or replacement.
7. Maruti Suzuki will not be responsible for the cost of transporta-
tion of the vehicle to the nearest Maruti Suzuki dealer work-
shop or any loss due to non-availability of the vehicle during
the period of lodging of a warranty claim and examination and/
or repair by Maruti Suzuki dealer.
8. Maruti Suzuki will not be responsible for any penalty that may
be charged by statutory authorities on account of failure to
comply with the EMISSION STANDARDS.
9. Emission Warranty will not be affected on the change of owner,
provided all the documents are available.
Page 14 of 190
0-6
82PH0-74E
10.All maintenance actions (as specified in the Owner’s Manual
and Service Booklet) need to be followed and recorded in the
manual for emission warranty.
11.The customer needs to produce the PUC (Pollution Under
Control) certificate valid for the period preceding the test during
which the failure is discovered. The receipts (for the mainte-
nance of the vehicle as per specification in Owner’s Manual
and Service Booklet from the date of original purchase of the
vehicle) will also be required.
Conditions under which the Emission Warranty is not
APPLICABLE
1. In the absence of valid PUC certificate.
2. Vehicle not serviced from Maruti Suzuki authorised workshop
as per the schedule specified in this Owner’s Manual and Ser-
vice Booklet.
3. Vehicle subjected to abnormal use (accident, motor race, ral-
lies or for the purpose of establishing the records etc).
4. Use of non MGP (Maruti Genuine Part).
5. Vehicle that has been tampered with.
6. Tampering with odometer so that the actual kilometer reading
can not be determined.
7. Use of adulterated fuel and/or unspecified oils (Engine oil,
Transmission oil and Brake oil etc).
Annexure - A
List of parts covered under Emission Warranty
1. Fuel Injection Assembly, Pressure Regulator, Throttle Body
Assembly
2. Electronic Control Module (ECM).
3. Intake Manifold.
4. EGR valve.
5. Ignition Coil.
6. Canister Assembly.
7. Vapour Liquid Seperator.
8. Fuel Tank and Filler Cap.
9. PCV (Positive Crankcase Ventilation) Valve.
10. Oil Filler Cap.
11. Catalytic Convertor.
12. Exhaust Manifold.
13. All Fuel Injection System related SENSORS.
14. High Pressure Fuel Pump.
15. Glow Plug.
16. Glow Plug Controller.
Page 49 of 190
2-30
BEFORE DRIVING
53MH0-74E
Warning and Indicator Lights
Brake System Warning Light
53M-04-072
Three different types of operations exist
depending on the vehicle’s specification.
1) The light comes on briefly when the
ignition switch is turned to the “ON”
position.
2) The light comes on when the parking
brake is engaged with the ignition
switch in the “ON” position.
3) The light comes on when under either
or both of above two conditions.
The light also comes on when the fluid in
the brake fluid reservoir falls below the
specified level.
The light should go out after starting the
engine and fully releasing the parking
brake, if the fluid level in the brake fluid res-
ervoir is adequate.
The light also comes on together with the
ABS warning light when the rear brake
force control function (proportioning valve
function) of the ABS system fails.
If the brake system warning light comes on
while you are driving the vehicle, it maymean that there is something wrong with
the vehicle’s brake system. If this happens,
you should:
1) Pull off the road and stop carefully.
2) Test the brakes by carefully starting and
stopping at the side of the road.
– If you determine that it is safe, drive
carefully at low speed to the nearest
dealer for repairs, or
– Have the vehicle towed to the nearest
dealer for repairs.
NOTE:
Because the disc brake system is self-
adjusting, the fluid level will drop as the
brake pads become worn. Replenishing
the brake fluid reservoir is considered nor-
mal periodic maintenance.
Seat Belt Warning Light
(if equipped)
53M-04-073
WA R N I N G
Remember that stopping distance
may be longer, you may have to push
harder on the pedal, and the pedal
may go down farther than normal.
WA R N I N G
If any of the following conditions
occur, you should immediately ask
your MARUTI SUZUKI dealer to
inspect the brake system.
• If the brake system warning light
does not go out after the engine
has been started and the parking
brake has been fully released.
• If the brake system warning light
does not come on when the igni-
tion switch is turned to the “ON”
position.
• If the brake system warning light
comes on at any time during vehi-
cle operation.
Page 55 of 190
2-36
BEFORE DRIVING
53MH0-74E
When the fuel meter indicator shows only
one segment to “E”, refill the tank as soon
as possible.
NOTE:
• If the last segment blinks, it means that
the fuel is almost empty.
• The fuel meter indicator varies depend-
ing on road conditions (for example,
slope or curve) and driving conditions
because of fuel moving in the tank.
Depress Brake Pedal Indicator
(if equipped)
53M-04-094
Information Display
ALTO 800
53MM02003
53M-04-095
(1) Clock (if equipped)
(2) Odometer/Trip meter
(3) Odometer/Trip meter/Meter illumina-
tion control knob
ALTO K10
Manual transaxle
Without tachometer
53M-04-096
With tachometer
53M-04-097
Automated Manual transaxle
Without tachometer
53M-04-098
(1) (2)(3)
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
Page 63 of 190
OPERATING YOUR VEHICLE
3
53MH0-74E
OPERATING YOUR VEHICLE
Exhaust Gas Warning ......................................................... 3-1
Daily Inspection Checklist .................................................. 3-1
Engine Oil Consumption .................................................... 3-2
Ignition Switch ..................................................................... 3-3
Parking Brake Lever ........................................................... 3-5
Pedal ..................................................................................... 3-6
Starting the Engine ............................................................. 3-7
Using the Transaxle ............................................................ 3-7
Braking ................................................................................. 3-16
Page 65 of 190
3-2
OPERATING YOUR VEHICLE
53MH0-74E
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint
(if equipped).
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened your seat belts.
10)Make sure that all warning lights come
on as the key is turned to the “ON” posi-
tion.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the
parking brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Windshield washer fluid level
5) Battery solution level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See “Alllatches, hinges & locks” of “CHASSIS
AND BODY” in the “Periodic Mainte-
nance Schedule” in the “INSPECTION
AND MAINTENANCE” section for lubri-
cation schedule.
Once a month, or each time you fill your
fuel tank, check the tire pressure using a
tire pressure gauge. Also check the tire
pressure of the spare tire.Engine Oil Consumption
It is normal for the engine to consume
some engine oil during normal vehicle
operation.
The amount of engine oil consumed
depends on the viscosity of the oil, the
quality of the oil and the conditions the
vehicle is driven under.
More oil is consumed during high-speed
driving and when there is frequent acceler-
ation and deceleration. Under high loads,
your engine also will consume more oil.
A new engine also consumes more oil,
since its pistons, piston rings and cylinder
walls have not yet become conditioned.
New engines reach the normal level of oil
consumption only after approximately 5000
km (3000 miles) driving.
Oil consumption:
Max. 1.0 L per 1000 km
When judging the amount of oil consump-
tion, note that the oil may become diluted
and make it difficult to accurately judge the
true oil level.
As an example, if a vehicle is used for
repeated short trips, and consumes a nor-
mal amount of oil, the dipstick may not
show any drop in the oil level at all, even
after 1000 km or more of driving. This is
because the oil is gradually becoming
diluted with fuel or moisture, making it
appear that the oil level has not changed.
WA R N I N G
Make sure the hood is fully closed
and latched before driving. If it is not,
it can fly up unexpectedly during
driving, obstructing your view and
resulting in an accident.
Page 68 of 190
3-5
OPERATING YOUR VEHICLE
53MH0-74E
Parking Brake Lever
60MHM03001
(1) To set
(2) To release
(3) To release
The parking brake lever is located between
the front seats. To set the parking brake,
hold the brake pedal down and pull the
parking brake lever all the way up. To
release the parking brake, hold the brake
pedal down, pull up slightly on the parking
brake lever, push the button on the end of
the lever with your thumb, and lower the
lever to its original position.
(2)
(3) (1)
EXAMPLE
WA R N I N G
• Never drive your vehicle with the
parking brake on: rear brake effec-
tiveness can be reduced from over-
heating, brake life may be
shortened, or permanent brake
damage may result.
• If the parking brake does not hold
the vehicle securely or does not
fully release, have your vehicle
inspected immediately by an autho-
rized MARUTI SUZUKI dealer.
WA R N I N G
Always set the parking brake fully
before leaving your vehicle or it may
move, causing injury or damage.
When parking, make sure the gear-
shift lever is in 1st gear. Remember,
even though the transaxle is in gear,
you must set the parking brake fully.
WA R N I N G
When parking the vehicle in
extremely cold weather, the following
procedure should be used:
1) Set the parking brake.
2) Manual transmission - turn off the
engine, then shift into reverse or
first gear, with ignition key “ON”
position.
Automated manual transaxle -
shift into reverse or first gear and
check the gear position indicator
in the instrument cluster to make
sure that the transaxle is engaged
in 1st or reverse, then turn the
ignition switch “LOCK” position.
3) Get out of the vehicle and put
chocks under the wheels.
4) Release the parking brake.
When you return to your vehicle,
you must remember to first set the
parking brake, then remove the
wheel chocks.
Page 69 of 190
3-6
OPERATING YOUR VEHICLE
53MH0-74E
Pedal
Manual Transaxle
80J2121
Auto Gear Shift
53M05009
Clutch Pedal (1)
(For manual transaxle)
The clutch pedal is used to disengage the
drive to the wheels when starting the
engine, stopping, or shifting the gearshift
lever. Depressing the pedal disengages
the clutch.
Brake Pedal (2)
Your MARUTI SUZUKI vehicle is equipped
with front disc brakes and rear drum
brakes. Depressing the brake pedal
applies both sets of brakes.
You may hear occasional brake squeal
when you apply the brakes. This is a nor-
mal condition caused by environmental
factors such as cold, wet, snow, etc.
Accelerator Pedal (3)
This pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output and speed.
(2)(1)
(3)
EXAMPLE
EXAMPLE
WA R N I N G
Do not drive with your foot resting on
the clutch pedal. It could result in
excessive clutch wear, clutch dam-
age, or unexpected loss of engine
braking.
WA R N I N G
If brake squeal is excessive and
occurs each time the brakes are
applied, you should have the brakes
checked by your MARUTI SUZUKI
dealer.
WA R N I N G
Do not “ride” the brakes by applying
them continuously or resting your
foot on the brake pedal. This will
result in overheating of the brakes
which could cause unpredictable
braking action, longer stopping dis-
tances, or permanent brake damage.
Page 70 of 190
3-7
OPERATING YOUR VEHICLE
53MH0-74E
Starting the Engine
Before Starting the Engine
76MH021
1) Make sure the parking brake is set fully.
2) Shift into “N” (Neutral) and depress the
clutch pedal all the way to the floor.
Hold the clutch pedal while starting the
engine.
Automated manual transaxle – Shift
into “N” (Neutral) and depress the brake
pedal. Hold the brake pedal while start-
ing the engine.
Starting a Cold and Warm Engine
With your foot off the accelerator pedal,
crank the engine by turning the ignition key
to “START”. Release the key when the
engine starts.
If the engine does not start after 15 sec-
onds of cranking, wait about 15 seconds,
then press down the accelerator pedal to
1/3 of its travel and try cranking the engine
again. Release the key and accelerator
pedal when the engine starts.
If the engine still does not start, try holding
the accelerator pedal all the way to the
floor while cranking. This should clear the
engine if it is flooded.
Using the Transaxle
Manual Transaxle
53MH0303
Starting off
To start off, depress the clutch pedal all the
way to the floor and shift into 1st gear.
After releasing the parking brake, gradually
release the clutch. When you hear a
change in the engine’s sound, slowly press
the accelerator while continuing to gradu-
ally release the clutch.
Shifting
All forward gears are synchronized, which
provides for quiet and easy shifting. Always
push in the clutch pedal fully before shifting
gears.
WA R N I N G
Make sure that the parking brake is
set fully and the transaxle is in Neu-
tral before attempting to start the
engine.
NOTICE
• Stop turning the starter immedi-
ately after the engine has started or
the starter system may be dam-
aged.
• Do not crank the engine for more
than 15 seconds at a time. If the
engine doesn’t start on the first try,
wait about 15 seconds before try-
ing again.