spark plug SUZUKI ALTO 2013 7.G Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2013, Model line: ALTO, Model: SUZUKI ALTO 2013 7.GPages: 190, PDF Size: 8.76 MB
Page 11 of 190
0-3
82PH0-74E
WARRANTY POLICY
Maruti Suzuki India Limited (hereinafter called “Maruti Suzuki”),
warrants that each new Maruti Suzuki vehicle distributed in India
by Maruti Suzuki and sold by an authorised Maruti Suzuki dealer
will be free, under normal use and service, from any defects in
material and workmanship at the time of manufacture SUBJECT
TO THE FOLLOWING TERMS AND CONDITIONS:
(1) Qualification:To qualify for this warranty the vehicle must be delivered by a
Maruti Suzuki authorised dealer and set-up, and serviced by a
Maruti Suzuki authorised dealer / service station.
(2) Term:The term of the warranty shall be twenty-four (24) months or
40,000 kilometers (whichever occurs first) from the date of
invoice to the first owner.
(3) Maruti Suzuki Warranty Obligation:If any defect(s) should be found in a Maruti Suzuki vehicle within
the term stipulated above, Maruti Suzuki’s only obligation is to
repair or replace at its sole discretion any part shown to be defec-
tive, with a new part or the equivalent at no cost to the owner for
parts or labour, when Maruti Suzuki acknowledges that such a
defect is attributable to faulty material or workmanship at the time
of manufacture. The owner is responsible for any repair or replace-
ments which are not covered by this warranty.
(4) Limitation:
This warranty shall not apply to:
(a) Normal maintenance service required other than the three
free services, including without limitation, oil and fluid
changes, headlight aiming, fastener retightening, wheel bal-
ancing, wheel alignment and tyre rotation, cleaning of injec-
tors, adjustments of clutch and valve clearance.
(b) The replacement of normal wear parts including without lim-
itation, bulbs, tyres and tubes, spark plugs, belts, hoses, fil-
ters, wiper blades, brushes, contact points, fuses, clutch
disc, brake shoes, brake pads, cable and all rubber parts
(except oil seal and glass run).
(c) Any vehicle which has been used for competition or racing.
(d) Any repairs or replacement required as a result of accidents
or collision.
(e) Any defects caused by misuse, negligence, abnormal use or
insufficient care.
(f) Any vehicle which has been modified or altered, including
without limitation, the installation of performance accesso-
ries.
(g) Any vehicle on which parts or accessories not approved by
Maruti Suzuki have been used.
(h) Any vehicle which has not been operated in accordance with
the operating instructions in this Owner’s Manual and Ser-
vice Booklet.
(i) Any vehicle which has not received, during the warranty term,
the service inspections prescribed in this Owner’s Manual
and Service Booklet.
(j) Any vehicle which has been assembled, disassembled,
adjusted or repaired by other than an Maruti Suzuki autho-
rised dealer/service station.
(k) Any vehicle which has been used for purposes other than
what it was designed for.
(l) Any damage or deterioration caused by industrial pollution
and bird droppings.
Page 85 of 190
4-2
DRIVING TIPS
53MH0-74E
54G584S
Improving Fuel Economy
The following instructions will help you
improve fuel economy.
Avoid excessive idling
If you are to wait for more than a minute
while you are parked, stop the engine and
start it again later. When warming up a
cold engine, do not allow the engine to idle
or apply full throttle until the engine has
reached operating temperature. Allow the
engine to warm up while driving.
Avoid sudden acceleration
Sudden acceleration starting from rest or
while driving will consume fuel unneces-
sarily and shorten engine life. Start off
slowly.
Avoid unnecessary stops
Avoid unnecessary deceleration and stop-
ping. Try to maintain a slow, steady speed
whenever possible. Slowing down and then
accelerating again uses more fuel.
Keep a steady cruising speed
Keep as constant a speed as road and traf-
fic conditions will permit.NOTICE
To avoid damaging catalyst or other
vehicle damage:
• Maintain the engine in the proper
operating condition.
• In the event of an engine malfunc-
tion, particularly one involving
engine misfiring or other apparent
loss of performance, have the vehi-
cle serviced promptly.
• Do not turn off the engine or inter-
rupt the ignition when the transaxle
is in gear and the vehicle is in
motion.
• Do not try to start the engine by
pushing or towing the vehicle, or
coasting down a hill.
• Do not idle the engine with any
spark plug wires disconnected or
removed, such as during diagnos-
tic testing.
• Do not idle the vehicle for pro-
longed periods if idling seems
rough or there are other malfunc-
tions.
• Do not allow the fuel tank to get
near the empty level.
• Avoid driving your vehicle at
excessively high engine speed.
WA R N I N G
Be careful about where you park and
drive; the catalytic converter and
other exhaust components can get
very hot. As with any vehicle, do not
park or operate this vehicle in areas
where combustible materials such as
dry grass or leaves can come in con-
tact with a hot exhaust system.
EXAMPLE
Page 137 of 190
INSPECTION AND MAINTENANCE
7
53MH0-74E
INSPECTION AND MAINTENANCE
Maintenance Schedule ....................................................... 7-2
Periodic Maintenance Schedule ........................................ 7-2
Drive Belt ............................................................................. 7-10
Engine Oil and Filter ........................................................... 7-10
Engine Coolant .................................................................... 7-13
Air Cleaner ........................................................................... 7-15
Spark Plugs ......................................................................... 7-15
Gear Oil ................................................................................ 7-16
Clutch Pedal ........................................................................ 7-17
Fuel Filter ............................................................................. 7-17
Brakes .................................................................................. 7-18
Steering ................................................................................ 7-20
Tires ...................................................................................... 7-20
Battery .................................................................................. 7-22
Fuses .................................................................................... 7-23
Bulb Replacement ............................................................... 7-27
Wiper Blades ....................................................................... 7-29
Windshield Washer Fluid ................................................... 7-31
Air Conditioning System .................................................... 7-31
Page 140 of 190
7-3
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ENGINE
1.Water pump drive belt (Tension, Wear) AIIIIIIRAI
2. Engine Coolant (Level, Leakage) I I I R I R I R I R
3.Engine oil and Oil filter R I RRRRRRRR
4. Cooling system hoses and connections (Leakage, Damage) I I IIIIIIII
5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –
6. Engine mounting (Loose, Damage) – – T – T – T – T –
7. Valve Clearance – A – A – A – A – A
8. Camshaft timing belt (Damage, Wear)–––I–I–I–I
Replace Every 1,00,000 km
9. Exhaust system (Noise, Leakage etc.) – I – I – I – I – I
10. Positive crankcase ventilation System (Hoses, Connections and Valve) – I – I – I – I – I
IGNITION
1. Ignition wiring (Damage, Deterioration) – – – I – I – I – I
2. Spark plugs (Clean and Adjust the gap) – – I R I R I R I R
FUEL
1. Air cleanerPaved-road Clean every 5,000 km. Replace after every 40,000 km.
Dusty condition Clean every 2,500 km or as required. Replace after every 40,000 km.
More frequent replacement if dust condition is severe.
2. Fuel tank cap, fuel lines and connections (Leakage, Damage) – I – – – I – – – I
3. Fuel filter (Leakage) I I I I I R I I I R
CLUTCH AND TRANMISSION
1. Clutch pedal (Play) I I IIIIIIII
2. Clutch slipping (Dragging or Excessive damage) I I IIIIIIII
3. Manual Transmission Oil (Level, Leakage)IIIIIIIIII
Replace every 1,60,000 kms or 10 years, which ever comes earlier
DRIVE SHAFTS
1. Drive shafts boot (Boot cut / Damage) – I IIIIIIII
2.Drive Shaft Noise IIIIIIIIII
Page 144 of 190
7-7
INSPECTION AND MAINTENANCE
53MH0-74E
*Interval: This interval should be judged by
odometer reading or months, whichever comes
first.km (x 1,000)
monthsFREE INSPECTIONS PERIODIC MAINTENANCE SERVICE AT COST
1 5 10 20 30 40 50 60 70 80
1 6 12 24 36 48 60 72 84 96
ENGINE
1.Water pump drive belt (Tension, Wear) ––––– I ––– I
2. Engine Coolant (Level, Leakage) I I I R I R I R I R
3. Engine oil and Oil filter – – RRRRRRRR
4. Cooling system hoses and connections (Leakage, Damage)IIIIIIIIII
5. Engine bolts (All cylinder head and manifold fixings) – – T – T – T – T –
6. Engine Mounting (Loose, Damage) – – T – T – T – T –
7.Valve Clearance –––– I –– I ––
8. Exhaust System (Noise, Leakage etc.) – I – I – I – I – I
9. Positive crankcase ventilation System (Hoses, Connections and Valve) – I – I – I – I – I
IGNITION
1. Ignition wiring (Damage, Deterioration) – – – I – I – I – I
2.Spark plugs –––––R–––R
FUEL
1. Air cleanerPaved-road Clean every 5,000 km. Replace after every 40,000 km.
Dusty condition Clean every 2,500 km or as required. Replace after every 40,000 km.
More frequent replacement if dust condition is severe.
2. Fuel tank cap, fuel lines and connections (Leakage, Damage) – I – – – I – – – I
3. Fuel filter (Leakage) – I I I I R I I I R
CLUTCH AND TRANMISSION
1.Clutch pedal (Play) IIIIIIIIII
2.Clutch slipping (Dragging or Excessive damage) IIIIIIIIII
3. Manual Transmission Oil (Level, Leakage)IIIIIIIIII
Replace every 1,60,000 kms or 10 years whichever comes first
DRIVE SHAFTS
1. Drive shaft boots (Boot cut / Damage)IIIIIIIIII
2.Drive Shaft Noise IIIIIIIIII
BRAKE
1. Brake fluid (Level, Leakage) I I I R I R I R I R
2. Brake pedal (Pedal-to-wall clearance)IIIIIIIIII
Page 152 of 190
7-15
INSPECTION AND MAINTENANCE
53MH0-74E
Coolant ReplacementSince special procedures are required, we
recommend you take your vehicle to your
MARUTI SUZUKI dealer for coolant
replacement.
Air Cleaner
ALTO 800
53MM07007
NOTE:
Remove hose (1) from air cleaner case
before unclamping.
ALTO K10
53M-09-017
Unclamp/Unscrew the side clamps/screws,
and remove the element from the air
cleaner case. If it appears to be dirty,
replace it with a new one.
Spark Plugs
You should inspect spark plugs periodically
for carbon deposits. When carbon accu-
mulates on a spark plug, a strong spark
may not be produced. Remove carbon
deposits with a wire or pin and adjust the
spark plug gap.
NOTE:
For ALTO K10: Unclamp the air filter bolt
and then remove the air cleaner case.
ALTO K10
53M-09-019
To access the spark plugs:
1) If necessary, disconnect the coupler (1)
while pushing the release lever.
2) Remove the ignition coil bolts (2).3) Pullout the ignition coil (3) and remove
the spark plug.
NOTE:
When installation, make sure the wires,
couplers, sealing rubber of top cover and
washers, are correctly returned in place.
53MM07008(1)
EXAMPLE
EXAMPLE
EXAMPLE
NOTICE
• When pulling the ignition coils out,
do not pull on the cable. Pulling on
the cable can damage it.
• When servicing the iridium/plati-
num spark plugs (slender center
electrode type plugs), do not touch
the center electrode, as it is easy to
damage.
(1)
(2)(3)
Wrong Right
EXAMPLE
Page 153 of 190
7-16
INSPECTION AND MAINTENANCE
53MH0-74E
60G160S
53MM07010
Spark plug gap “a”ALTO 800
NGK DCPR7E, BOSCH YR7DC
0.8 - 0.9 mm (0.031 - 0.035 in.)
ALTO K10
NGK KR6A-10:
0.95 - 1.05 mm (0.037 - 0.041 in.)
Gear Oil
Manual Transaxle Oil
When adding gear oil, use gear oil with the
appropriate viscosity and grade.
We highly recommend you use: “MARUTI
Genuine GEAR OIL 75W-80” for manual
transaxle gear oil or automated manual
transaxle oil.
Manual transaxle oil (API GL-4)
53M-09-023
Gear Oil Level Check
68KH073
(1) Oil filler and level plug
To check the gear oil level, use the follow-
ing procedure:
1) Park the vehicle on a level surface with
the parking brake applied. Then, stop
the engine.
2) Remove the oil filler plug (1) or (2).
3) Check the inside of the hole with your
finger. If the oil level comes up to the
bottom of the plug hole, the oil level is
correct. If so, reinstall the plug.
4) If the oil level is low, add gear oil
through the oil filler plug hole (1) or (2)
until the oil level reaches the bottom of
the filler hole, then reinstall the plug.
Tightening torque (1):
21 Nm (2.1 kg-m, 15.5 lb-ft)
NOTICE
• When installing the spark plugs,
screw them in with your fingers to
avoid stripping the threads.
Tighten with a torque wrench to
25 Nm (2.5 kg-m, 18.0 lb-ft). Do not
allow contaminants to enter the
engine through the spark plug
holes when the plugs are removed.
• Never use spark plugs with the
wrong thread size.
EXAMPLE
“a”
EXAMPLE
NOTICE
When replacing spark plugs, you
should use the brand and type speci-
fied for your vehicle. For the speci-
fied spark plugs, refer to the
“SPECIFICATIONS” section at the
end of this book.
(1)
EXAMPLE
Page 188 of 190
11-2
SPECIFICATIONS
53MH0-74E
ITEM: Engine
ALTO 800 ALTO K10
Ty p e F 8 D K 1 0 B
Number of cylinders 3 3
Bore 68.5 mm 73 mm
Stroke 72.0 mm 79.5 mm
Piston displacement 796 cm
3 (796 cc) 998 cm3 (998 cc)
Compression ratio 10.95 ± 0.4 : 1
11 ± 0.4 : 1
ITEM: Electrical
ALTO 800 ALTO K10
Standard spark plug Nickel plug NGK DCPR7E, BOSCH YR7DC
NGK, KR6A-10
Battery 12V 34B1912V 34B19
Fuses See “INSPECTION AND MAINTENANCE” section.