hood open SUZUKI BALENO 1999 1.G Owners Manual

60G-74E
OPERATING YOUR VEHICLE

Once a week, or each time you fill your fuel

tank, perform the following under-bonnet

checks:

1) Engine oil level.

2) Coolant level.

3) Brake fluid level.

4) Power steering (if equipped) fluid level.

5) Windscreen washer fluid level.

6) Battery solution level.

7) Bonnet latch operation.

Pull the bonnet release handle inside the

vehicle. Make sure that you can not open

the hood all the way without releasing the

secondary latch. Be sure to close the hood

securely after checking for proper

operation. See "All Latches, Hinges &

Locks" of "PERIODIC MAINTENANCE

SCHEDULE" in the "INSPECTION AND

MAINTENANCE" section for lubrication

schedule.

Make sure the bonnet is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
STARTING THE ENGINE

Before starting the engine:

1) Make sure the parking brake is applied

fully.

2) Manual Transmission - Shift into "N"

(neutral) and depress the clutch pedal all

the way to the floor. Hold it while starting

the engine.

Make sure that the parking brake is

applied fully and the transmission is in

Neutral before attempting to start the

engine.

CAUTION

Stop turning the starter immediately

after the engine has started or the

starter system can be damaged.

Do not crank the engine for more

than 15 seconds at a time. If the

engine doesn't start on the first try,

wait about 15 seconds before trying

again.
Starting a Cold Engine

Engine which is started after 6 hours should

be treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,

crank the engine by turning the ignition

key to "START1. Release the key when the

engine starts.

• If the engine does not start after 15

seconds of cranking, wait about 15

seconds, then press down the accelerator

pedal to 1/3 of its travel and try cranking

the engine again. Release the key and

accelerator pedal when the engine starts.

• If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for "Starting a cold

Engine".

67

7-2

OPERATING YOUR VECHILE

60G-74E

USING THE TRANSMISSION

70F-04-005E

Starting off

To start off, depress and maintain pressure

upon the clutch pedal and change into 1st

gear. After releasing the parking brake,

gradually release the clutch. When you hear

a change in the engine's sound (speed), gently

apply pressure to the accelerator to keep the

engine sound (speed) constant whilst

continuing to gradually release the clutch.
Gear changing

All forward gears are synchronized, which

provides for quiet, easy changing. Always

depress the clutch pedal fully before changing

gears.The following table shows the maximum

allowable speed for each gear.
GEAR

First

Second

Third

Fourth

Fifth
MAXIMUM SPEED

50 km/h

95 km/h

140 km/h

Top Speed

Top Speed

7-3
68

EMERGENCY SERVICE

60G-74E

CAUTION

Vehicle equipped with electronic fuel

injection system will not start by

pushing or towing as the fuel pump

will not work in this condition. This

starting method could also result in

permanent damage to the catalytic

converter. Use jump leads to start a

vehicle with a weak or flat battery.

60G-10-004E

When jump starting your vehicle, use the

following procedure:

1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12V battery

close to your vehicle so that the jump leads

will reach both batteries. When using a

battery installed on another vehicle, DO

NOT LET THE VEHICLES TOUCH. Apply

the parking brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).
3) Make jump lead connections as follows:

a) Connect one end of the first jump lead

to the positive (+) terminal of the flat

battery.

b) Connect the other end to the positive

(+) terminal of the booster battery.

c) Connect one end of the second jump

lead to the negative (-) terminal of the

booster battery.

d) Make the final connection to an

unpainted, heavy metal part of the

engine of the vehicle with the flat

battery.

Never connect the jump lead directly

to the negative (-) terminal of the

discharged battery, or an explosion

may occur.

10-3
4) If the booster battery you are using is fitted

to another vehicle, start the engine of the

vehicle with the booster battery. Run the

engine at moderate speed.

5) Start the engine of the vehicle with the flat

battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

118

60G-74E
EMERGENCY SERVICE

TOWING

If you need to have your vehicle towed, contact

a professional service.

CAUTION

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

Manual Transmission

Whenever possible, your vehicle should be

towed from the front with the front wheels lifted.

If the steering and drivetrain are in good

condition, your vehicle may be towed from the

rear with the rear wheels lifted and the front

wheels on the ground. Before towing, make

sure the steering is unlocked and the

transmission is in neutral.
EMERGENCY REMEDIES

If the Starter Does Not Operate:

1) Try turning the ignition switch to the

"START" position with the headlights

turned on to determine the battery

condition. If the headlights go excessively

dim or go off, it usually means that either

the battery is flat or the battery terminal

contact is poor. Recharge the battery or

correct battery terminal contact as

necessary.

2) If the headlights remain bright, check the

fuses. If the reason for failure of the starter

is not obvious, there may be a major

electrical problem. Have the vehicle

inspected by your authorized MARUTI

dealer.

If the Engine is Flooded

If the engine is flooded with petrol, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor and

hold it there while cranking the engine. (Do

not operate the starter motor for more than

15 seconds). Release the accelerator as soon

as the engine has started.
If the Engine Overheats

The engine could overheat temporarily under

severe driving conditions. If the engine coolant

temperature gauge indicates overheating

during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and park.

3) Let the engine run at normal idle speed

for a few minutes until the indicator is within

the normal, acceptable temperature range

between "H" and "C".

If you see or hear escaping steam, stop

the vehicle in a safe place and

Immediately turn off the engine to let it

cool. Do not open the bonnet when

steam is present. When the steam can

no longer be seen or heard, open the

hood to see if the coolant is still boiling.

If it is, you must wait until it stops

boiling before you proceed.

119

10-4