oil type SUZUKI BALENO 1999 1.G Owners Manual

60G-74E

BEFORE DRIVING

Pregnant women should use seat

belts, although specific recommen-

dations about restraint use should

be made by the woman's medical

advisor.

Periodically inspect seat belt

assemblies for excessive wear and

damage. Seat belts should be replaced

if webbing becomes frayed,

contaminated, or damaged in any way.

It is essential to replace the entire seat

belt assembly after it has been

stressed in an impact, even if damage

to the assembly is not obvious.

Infants and small children should never

be transported unless they are properly

restrained. Restraint systems for

infants and small children can be

purchased locally and should be used.

Make sure that the system you

purchase meets applicable safety

standards. Read and follow all the

directions provided by the

manufacturer.
Avoid contamination of seat belt

webbing by polishes, oils, chemicals,

and particularly battery acid. Cleaning

may safely be carried out using mild

soap and water.

For children, if the shoulder belt

irritates the neck or face, move the child

closer to the center of the vehicle.

A WARNING

Be sure to inspect all seat belt

assemblies after any collision. Any seat

belt assembly which was in use during

a collision (other than a very minor one)

should be replaced, even if damage to

the assembly is not obvious. Any seat

belt assembly which was not in use

during a collision should be replaced

if it does not function properly or is

damaged in any way.
70F-01-021

There are two types of seat belt, "Lap-shoulder

belt" and "Lap belt".

To fasten the seat belt, sit up straight and well

back in the seat, pull the buckle tongue

attached to the seat belt across your body and

slide it into the buckle catch on the opposite

side until you hear a "click".

25

3-12

BEFORE DRIVING
60G-74E

70F-01-022E

To reduce the risk of sliding under the belt

during a collision, position the lap portion of

the belt across your lap as low on your hips

as possible and adjust the belt to a snug fit

using the proper method for each type of the

belt as described below. Make sure that the

belt is not twisted.
70F-01-023E

To unfasten the belt, press the release button

on the buckle catch.
70F-01-024E

To Adjust the Belt

• Lap-shoulder belt

Pull the shoulder portion of the belt

upwards through the tongue plate.

The length of the diagonal shoulder strap

adjusts itself to allow freedom of movement.

The seat belt has an emergency locking

retractor (ELR), which is designed to lock the

seat belt only during a sudden stop or impact.

3-13
26

60G-74E
INSTRUMENT PANEL

60G-05-024

Dehumidifying

Push in the A/C button, and the desired

function button and move the air intake lever

to "FRESH AIR", the temperature control lever

to the desired temperature position, and the

fan switch to the desired fan speed position.

NOTE:

Because the air conditioner dehumidifies the

air, turning it on will help keep the windows

clear, even when blowing heated air using the

DEMIST or HEATER & DEMIST functions.
60G-05-025

NOTE:

There are two types of air conditioning

systems used in MARUTI vehicles. One type

uses refrigerant CFC-12, commonly called R-

12; the other type uses the new refrigerant

HFC-134a, commonly called R-134a. For each

system, the correct refrigerant must be used.

To identify the system, a label that states

"R134a" or "HFC 134a" is stuck on the front

side of the engine compartment if the system

uses R-134a refrigerant.
CAUTION

Using the wrong refrigerant may

damage the air conditioning system.

Use correct refrigerant only. Do not mix

the two refrigerants.

60G-74E
5-14

OTHER CONTROLS AND EQUIPMENT

OTHER CONTROLS AND EQUIPMENT

Parking Brake Lever 6-1

Pedals 6-2

Gear Lever 6-2

Fuel Filler Cap 6-3

Folding Rear Seats 6-4

Sun Visor 6-5

Interior Light Switch 6-5

Assist Grips 6-5

Bonnet 6-6

Cup Holder (if equipped) 6-7

Tyre Changing Tools 6-7

Luggage Compartment Trim 6-8

Trunk (Boot) Light 6-8

Front Seat Back Pocket (if equipped) 6-9

Rear spoiler with Stop lamp (if equipped) 6-9

Alloy Wheels (if equipped) 6-9

Power Antenna (if equipped) 6-10

Leather Cover (if equipped) 6-10

High Mount Stop Lamp 6-10

53

60G-74E
INSTRUMENT PANEL

60G-05-024

Dehumidifying

Push in the A/C button, and the desired

function button and move the air intake lever

to "FRESH AIR", the temperature control lever

to the desired temperature position, and the

fan switch to the desired fan speed position.

NOTE:

Because the air conditioner dehumidifies the

air, turning it on will help keep the windows

clear, even when blowing heated air using the

DEMIST or HEATER & DEMIST functions.
60G-05-025

NOTE:

There are two types of air conditioning

systems used in MARUTI vehicles. One type

uses refrigerant CFC-12, commonly called R-

12; the other type uses the new refrigerant

HFC-134a, commonly called R-134a. For each

system, the correct refrigerant must be used.

To identify the system, a label that states

"R134a" or "HFC 134a" is stuck on the front

side of the engine compartment if the system

uses R-134a refrigerant.
CAUTION

Using the wrong refrigerant may

damage the air conditioning system.

Use correct refrigerant only. Do not mix

the two refrigerants.

60G-74E
5-14

OTHER CONTROLS AND EQUIPMENT

OTHER CONTROLS AND EQUIPMENT

Parking Brake Lever 6-1

Pedals 6-2

Gear Lever 6-2

Fuel Filler Cap 6-3

Folding Rear Seats 6-4

Sun Visor 6-5

Interior Light Switch 6-5

Assist Grips 6-5

Bonnet 6-6

Cup Holder (if equipped) 6-7

Tyre Changing Tools 6-7

Luggage Compartment Trim 6-8

Trunk (Boot) Light 6-8

Front Seat Back Pocket (if equipped) 6-9

Rear spoiler with Stop lamp (if equipped) 6-9

Alloy Wheels (if equipped) 6-9

Power Antenna (if equipped) 6-10

Leather Cover (if equipped) 6-10

High Mount Stop Lamp 6-10

53

60G-74E
INSPECTION AND MAINTENANCE

GEAR OIL

CAUTION

To prevent oil leakage, make sure that

the oil filter is tight, but do not

overtighten it.

Refill with oil and check for leaks.

1) Pour 3.1 litres of oil through the filler hole

and install the filler cap.

2) Start the engine and look carefully for

leaks at the oil filter and drain plug. Run

the engine at various speeds for at least 5

minutes.

3) Stop the engine and wait for 5 minutes.

Check the oil level again and add oil if

necessary. Check for leaks again.

CAUTION

When replacing the oil filter, it is

recommended that you use a genuine

MARUTI replacement filter.
60G-09-006

CAUTION

Oil leaks from around the oil filter or

drain plug indicate incorrect

installation or gasket damage. If you

find any leaks or are not sure that the

fitter has been properly tightened, have

the vehicle inspected by your MARUTI

dealer.
70F-07-012E

Oil filler and level plug ©

Tightening torque: 2.1 kg-m (15.5 Ib-ft)

Specified Manual Transmission oil

When adding gear oil, use the appropriate

viscosity and grade as shown in the chart

below. We highly recommend you use API

GL-4 SAE 75W-90 gear oil.

Type of oil
Gear oil, API GL-4

93

9-10

INSPECTION AND MAINTENANCE

60G-74E

ENGINE COOLANT

70F-07-013E

Gear oil level check

To check the gear oil level, use the following

procedure:

1) Park the vehicle on a level surface with

the parking brake applied.

2) Clean casing around oil filler plug to

remove risk of any loose dirt or debris

entering oil filler plug hole. Remove the oil

filler plug ©.

3) Feel the inside of the hole with your finger.

If the oil level comes up to the bottom of

the plug hole, the oil level is correct. If so,

reinstall the plug.

4) If the oil level is low, add gear oil through

the filler plug hole © until the oil level

reaches the bottom of the filler hole, then

reinstall the plug.
After driving the vehicle, the

transmission oil temperature may be

high enough to burn you. Wait until the

oil filler plug is cool enough to touch

with your bare hands before inspecting

transmission oil.

CAUTION

When tightening the plug, apply sealing

compound to the plug threads to

prevent oil leakage.

Gear oil change

Since special procedures, materials and tools

are required, it is recommended that you trust

this job to your authorized MARUTI dealer.
60G-09-007

Coolant Level Check

Check the coolant level at the reservoir tank,

not at the radiator. With the engine cool, the

coolant level should be between the "FULL"

and "LOW" marks.

Adding Coolant

If the Coolant level is below the "LOW" mark,

more coolant should be added. Remove the

reservoir tank cap and add coolant until the

reservoir tank level reaches the "FULL" mark.

Never fill the reservoir tank above the "FULL"

mark.

9-11
94

60G-74E
INSPECTION AND MAINTENANCE

BATTERY

60G-09-022E

When installing the cover, make sure that it is

positioned so that it does not cover or foul the

air valve.
60G-09-038

Batteries produce flammable hydrogen

gas. Keep flames and sparks away from

the battery or an explosion may occur.

Never smoke when working in the

vicinity of the battery .

When checking or servicing the battery,

disconnect the negative cable. Be

careful not to cause a short circuit by

allowing metal objects to contact the

battery posts and the vehicle at the

same time.
To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions in the

EMERGENCY SERVICE section of this

manual if it is necessary to jump start

your vehicle.

The level of the battery solution must be kept

between the "UPPER" and the "LOWER" level

lines at all times. If the level is found to be

below the "LOWER" level line, add distilled

water to the "UPPER" level line. You should

periodically check the battery, battery

terminals, and battery holddown bracket for

corrosion. Remove corrosion using a stiff

brush and ammonia mixed with water, or

baking soda mixed with water. After removing

corrosion, rinse with clean water.

If your vehicle is not going to be driven for a

month or longer, disconnect the cable from

the negative terminal of the battery to help

prevent discharge.

105

9-22

INSPECTION AND MAINTENANCE

60G-74E

FUSES

60G-09-024E

©. Main fuse

®. Primary fuse (Lights)

®. Primary fuse (IG)

©. Radiator fan motor fuse

©. Primary fuse (A/C, HTR)

This vehicle has three types of fuses, as

described below:

Main Fuse - The main fuse takes current

directly from the battery.

Primary Fuses - These fuses are between the

main fuse and individual fuses, and are for

electrical load groups.

Individual Fuses - These fuses are in the fuse

box and for individual electrical circuits.
MAIN FUSE / PRIMARY FUSES

80A

60A

60A

30A

60A
All Electric Load

HEAD-R, HEAD-L, TAIL/DOME,

STOP/HORN, HAZARD

CIGAR/RADIO, I.G. COIL/

METER, WIPER/WASHER,

REAR DEF, TURN/BACK,

HEATER RELAY.

RADIATOR FAN MOTOR

A/C, HTR

Main Fuse and Primary Fuses

The main fuse and primary fuses are located

in the engine compartment. If the main fuse

blows, no electrical component will function.

If a primary fuse blows, no electrical

component in the corresponding load group

will function. When replacing the main fuse or

a primary fuse, use a genuine MARUTI

replacement.

If the main fuse or a primary fuse blows,

be sure to have your vehicle inspected

by an authorized MARUTI dealer.

Always use a genuine MARUTI

replacement. Never use a substitute

such as a wire even for a temporary

repair, or extensive electrical damage

and a fire can result.
60G-09-025E

Fuse Box

The fuse boxes are located in the engine

compartment and under the driver's side of

the dashboard.

To remove the fuse box cover under the

dashboard pull off the cover.

9-23
106

60G-74E
BODY WORK CARE

BODY WORK CARE

Corrosion Prevention 11-1

Vehicle Cleaning 11-2

123

BODY WORK CARE

60G-74E

CORROSION PREVENTION

It is important to take good care of your vehicle

to protect it from corrosion.

Listed below are instructions for how to

maintain your vehicle to prevent corrosion.

Please read and follow these instructions

carefully.

Important Information About Corrosion

Common causes of corrosion

1) Accumulation of road salt, dirt, moisture,

or chemicals in hard to reach areas of the

vehicle underbody or frame.

2) Chipping, scratches and any damage to

treated or painted metal surfaces resulting

from minor accidents or abrasion by

stones and gravel.

Environmental conditions which accelerate

corrosion

1) Road salt, dust control chemicals, sea air

or industrial pollution will all accelerate the

corrosion of metal.

2) High humidity will increase the rate of

corrosion particularly when the

temperature range is just above the

freezing point.

3) Moisture in certain areas of a vehicle for

an extended period of time may promote

corrosion even though other body sections

may be completely dry.

11-1
4) High temperatures will cause an

accelerated rate of corrosion to parts of

the vehicle which are not well ventilated

to permit quick drying.

This information illustrates the necessity of

keeping your vehicle (particularly the

underbody) as clean and dry as possible. It is

equally important to repair any damage to the

paint or protective coatings as soon as

possible.

How to Help Prevent Corrosion

Wash your vehicle frequently

The best way to preserve the finish on your

vehicle and to help avoid corrosion is to keep it

clean with frequent washing.

Wash your vehicle regularly during the winter

and immediately after the winter. Keep your

vehicle, particularly the underside, as clean and

dry as possible.

If you frequently drive on salted roads, your

vehicle should be washed at least once a month

during the winter. If you live near the ocean,

your vehicle should be washed at least once a

month throughout the year.

For washing instructions, refer to the "VEHICLE

CLEANING" section.

Remove foreign material deposits

Foreign material such as salts, chemicals, road

oil or tar, tree sap, bird droppings and industrial

fall-out may damage the finish of your vehicle
if it is left on painted surfaces. Remove these

types of deposits as quickly as possible. If these

deposits are difficult to wash off, an additional

cleaner may be required. Be sure that any

cleaner you use is not harmful to painted

surfaces and is specifically intended for your

purposes. Follow the manufacturer's directions

when using these special cleaners.

Repair finish damage

Carefully examine your vehicle for damage to

the painted surfaces. Should you find any chips

or scratches in the paint, touch them up

immediately to prevent corrosion from starting.

If the chips or scratches have gone through

to the bare metal, have a qualified body shop

make the repair.

Keep Passenger and luggage

compartments clean.

Moisture, dirt or mud can accumulate under

the floor mats and may cause corrosion.

Occasionally, check under these mats to

ensure that this area is clean and dry. More

frequent checks are necessary if the vehicle

is used off road or in wet weather.

Certain cargos such as chemicals, fertilizers,

cleaners, salts, etc., are extremely corrosive

by nature. These products should be

transported in sealed containers. If a spill or

leak does occur, clean and dry the area

immediately.

124