tow SUZUKI BALENO 1999 1.G Owners Manual

60G-74E

BEFORE DRIVING

REMOTE KEYLESS ENTRY SYSTEM

Other Controls (if equipped)
KEYS

60G-50-001E

Remote keyless entry system is installed in

your vehicle. The general features of keyless

entry system are;

1. Remote lock/arming and remote unlock/

disarming.

2. Doors/trunk/bonnet protection.

3. Doors/trunk/bonnet open signal.

4. Personal protection alarm.

5. Mute lock/unlock.

6. Starter immobiliser.

7. Permanent siren chirp enable/disable

(programmable mode).

8. Two stage shock/impact sensor

(programmable mode).

9. Emergency disarm by personalised

PINCODE (programmable mode).

10. Car locator

11. Flashing LE.D.

15
Initially the system is programmed in factory

default. The features operative in factory

default are;

1. Remote lock/arming and remote unlock/

disarming.

2. Doors/trunk/bonnet protection.

3. Doors/trunk/bonnet open signal while

locking/arming.

4. Personal protection alarm.

5. Starter immobiliser.

6. Mute lock/unlock.

7. Permanent siren chirp enable/disable.

8. Emerging disarm by personalised

PINCODE.

9. Car locator.

10. Flashing LE.D.

The system can always be programmed back

to factory default for restoration of original

setting of the system.

For more detail and warranty condition, please

refer to the Owner's Manual of "Maruti Mobile

Security".
70F-01-003

Your vehicle comes with a pair of identical keys.

Keep the spare key in a safe place.

One key can open all of the locks on the vehicle.

The key identification number is stamped on a

metal tag provided with the keys. Keep

the tag in a safe place. If you lose your

keys, you will need this number to have

new keys made. Write the number down

and keep it in a safe accessible place away from

the vehicle.

NOTE:

Keep the spare key very carefully. When it

is lost, consult your dealer by quoting key number.

3-2

BEFORE DRIVING
60G-74E

DOOR LOCKS

60G-03-003

Ignition Key Reminder (if equipped)

A buzzer sounds intermittently to remind you

to remove the ignition key if it is in the ignition

switch when the driver's door is opened.
72F-03-002E

To lock a front door from outside the

vehicle:

a) Insert the key fully and turn the top of

the key toward the front of the vehicle,

or

b) Push in the lock knob down and hold

the door handle up as you close the

door.

To unlock a front door from outside the

vehicle, insert the key fully and turn the top

of the key toward the rear of the vehicle.

To lock a rear door from outside the vehicle,

push in the lock knob down and close the

door.
60G-03-004E

To lock a door from inside the vehicle, push

the lock knob down. Pull the lock knob up to

unlock the door.

3-3
16
Always lock all doors when driving.

Locking the door prevents occupants

from being thrown from the vehicle in

the event of an accident. It also helps

prevent unintentional opening of the

doors.

6OG-74E
STEERING COLUMN CONTROLS

ACC

Accessories such as the radio can operate,

but the engine is off.

ON

This is the normal operating position. All

electrical systems are on.

START

This is the position for starting the engine using

the starter motor. The key should be released

from this position as soon as the engine starts.

Never remove the ignition key while

the vehicle is moving. The steering

wheel will lock and you will not be

able to steer the vehicle.

Do not leave children alone In a

parked vehicle. Unattended children

could cause accidental movement of

the vehicle, which could result in

severe personal Injury.

Always remove the key when parked

to prevent unintentional operation of

the vehicle and to improve security.
LIGHTING/TURN SIGNAL

CONTROL LEVER

CAUTION

Do not use the starter motor for

more than 15 seconds at a time. If

the engine does not start; wait 15

seconds before trying again. If the

engine does not start after several

attempts, check the fuel and ignition

systems or consult your MARUTI

dealer.

Do not leave the ignition switch in

the "ON" position if the engine is not

running as the battery will

discharge.
60G-04-003

This control lever is located on the outboard

side of the steering column. Operate the lever

as described below.

Lighting Operation

To turn the lights on or off, twist the knob on

the end of the lever. There are three positions:

in the "OFF" position all lights are off; in the

middle position the front parking lights, tail-

lights, registration plate light, and instrument

lights are on, but the headlights are off; in the

third position the headlights come on in

addition to the other lights.

33

4-2

STEERING COLUMN CONTROLS
60G-74E

With the headlights on, push the lever forward

to switch to the high beams (main beams) or

pull the lever toward you to switch to the low

beams. When the high beams (main beams)

are on, a light on the instrument panel will

come on. To flash the high beams (main

beams) pull the lever slightly towards you and

release it.

Lights "On" Reminder (if Equipped)

A buzzer/chime sounds to remind you to turn

off the lights if they are left on when the ignition

key is removed and the driver's door is opened.
Turn Signal Operation

With the ignition switch in the "ON" position,

move the lever up or down to activate the left

or right turn signals.

Normal Turn Signal

Move the lever clockwise until it clicks to signal

a right turn or anticlockwise to signal a left

turn. When the turn is completed, the signal

will cancel and the lever will return to its normal

position.
6OG-04-006

Lane Change Signal

Some times, such as when changing lanes,

the steering wheel is not turned far enough

to cancel the turn signal. For convenience,

you can flash the turn signal by moving the

lever part way and holding it there. The

lever will return to its normal position when

you release it.

4-3
34
60G-04-006

60G-04-005

60G-04-004E

60G-74E

STEERING COLUMN CONTROLS

WINDSCREEN WIPER AND

WASHER LEVER

60G-04-007E

Windscreen Wipers

To turn the windscreen wipers on, move the

lever down to one of the three operating

positions. In the "INT position (if equipped),

the wipers operate intermittently. The "INT'

position is very convenient for driving in mist

or light rain. In the "LO" position, the wipers

operate at a steady low speed. In the "HI"

position, the wipers operate at a steady high

speed. To turn off the wipers, move the lever

back to the "OFF position.
60G-04-008E

If the lever is equipped with "INT TIME" control,

turn the control toward the "SLOW" or "FAST'

positions to adjust the intermittent wiper

operation to the desired interval.

60G-04-011E

The operation of windscreen wiper and washer

Type-2 is same as Type-1.
60G-04-009E

Windscreen Washer

To spray windscreen washer fluid, pull the

lever toward you. The windscreen wipers will

automatically turn on at low speed if

they are not already on and the "INT" position

is equipped.

To prevent windscreen icing in cold

weather, turn on the defroster to heat

the windscreen before and during

windscreen washer use.

Do not use radiator antifreeze in the

windscreen washer reservoir. It can

severely impair visibility when

sprayed on the windscreen, and can

also damage your vehicle's paint.

35

4-4

STEERING COLUMN CONTROLS
60G-74E

CAUTION

To help prevent damage to the

windscreen wiper and washer system

components, you should take the

following precautions:

• Do not continue to hold in the lever

when there is no windscreen washer

fluid being sprayed or the washer

motor can be damaged.

• Do not attempt to remove dirt from

a dry windscreen with the wipers or

you can damage the windscreen and

the wiper blades. Always wet the

windscreen with washer fluid before

operating the wipers.

• Clear ice or packed snow from the

wiper blades before using the

wipers.

• Check the washer fluid level

regularly. Check it often when the

weather is bad.

• Only fill the washer fluid reservoir

3/4 full during cold weather to allow

room for expansion if the

temperature falls low enough to

freeze the solution.
HORN
REAR WIPER AND WASHER

(if equipped)

60G-04-010

Press the horn button of the steering wheel to

sound the horn. The horn will sound with the

ignition switch in any position.
Press the button located at the end of the

windscreen wiper and washer lever to operate

the rear washer and turn the lever anti

clockwise to operate the rear washer.

4-5
36

60G-74E
INSTRUMENT PANEL

INSTRUMENT CLUSTER

© Speedometer

® Odometer

© Trip meter (if equipped)

© Trip meter reset knob

© Tachometer (if equipped)

© Fuel gauge

® Temperature gauge

© Warning and indicator lights

60G-05-002

39

5-2

INSTRUMENT PANEL
60G-74E

WARNING AND INDICATOR LIGHTS

70F-07-070

Brake fluid level warning/Parking Brake

Indicator light

This light operates under three conditions:

1) when the ignition switch is turned to the

"START' position, 2) when the fluid in the brake

fluid reservoir falls below the specified level

or 3) when the parking brake is not fully

released and the ignition switch is in the "ON"

position. The light should go out after starting

the engine and fully releasing the parking

brake, if the fluid in the brake fluid reservoir is

adequate. If the light does not go off or comes

on whilst you are driving, it may mean that

there is something wrong with the vehicle's

braking system. If this happens, you should:

1) Pull off the road and stop carefully.

Remember that stopping distance may

be longer, you may have to push

harder on the pedal, and the pedal

may go down farther than normal.
2) Test the brakes by carefully starting and

stopping at the side of the road.

3) If you determine that it is safe, drive

carefully at low speed to the nearest dealer

for repairs.

Have the vehicle towed to the nearest

dealer for repairs.
or

4)

If any of the following conditions occur,

you should Immediately ask your

MARUTI dealer to inspect the brake

system.

• If the brake fluid level warning light

does not go out after the engine has

been started and the parking brake

has been fully released.

• If the brake fluid level warning light

does not come on when the ignition

switch is turned to the "START"

position.

• If the brake fluid level warning light

comes on at any time during vehicle

operation.

NOTE:

Because the disc brake system is self

adjusting, the fluid level will drop as the brake

pads become worn.

Replenishing the brake fluid reservoir is

considered normal periodic maintenance.
70F-03-039

Oil Pressure Light

This light comes on when the ignition switch

is turned on, and goes out when the engine

is started. The light will come on and remain

on if there is insufficient oil pressure. If the

light comes on when driving, pull off the

road as soon as you can and stop the

engine. Check the oil level and add oil if

necessary (see pages 9-8 and 9-9). If there

is enough oil, the lubrication system should

be inspected by your MARUTI dealer before

you drive the vehicle again.

5-3
40

OTHER CONTROLS AND EQUIPMENTS

60G-74E

SUN VISOR
INTERIOR LIGHT SWITCH

70F-04-024

Luggage or other cargo should be

stowed in the luggage compartment

with the rear seat in an upright position,

whenever possible. If you need to carry

cargo in the passenger compartment

with the rear seat back folded forward,

be sure to secure the cargo or it may

be thrown about, causing injury. Never

pile cargo higher than the seatbacks.
The sun visors can be pulled down to block

glare coming through the wind screen, or they

can be unhooked and turned to the side to

block glare coming through the side window.

CAUTION

When unhooking and hooking a sun

visor, be sure to handle it by the hard

plastic parts or the sun visor can be

damaged.
60G-06-004

This light switch has three positions which

function as described below:

© The light comes on and stays on

regardless of whether the door is open or

closed.

© The light comes on when the door is

opened.

® The light remains off even when the door

is opened.

NOTE:

Both Front and Rear doors are involved in

lighting operation of the interior light.

6-5
58

60G-74E
OTHER CONTROLS AND EQUIPMENT

ASSIST GRIPS
BONNET

70F-04-015

Assist grips are provided for passenger

convenience.

Do not hang Herns on the assist grips.

They could obstruct the driver's view,

resulting in an accident, or could be

thrown about in an accident or abrupt

manoeuvre, causing injury.
60G-06-005

To open the bonnet:

1) Pull the bonnet release handle located on

the outboard side of the driver's side of

the instrument panel. This will disengage

the bonnet lock halfway.
60G-06-006

2)
Push the under-bonnet release lever

sideways with your finger, as shown in the

illustration. While pushing the lever, lift up

the bonnet.

59
6-6

OTHER CONTROLS AND EQUIPMENTS

60G-74E

CUP HOLDER (if equipped)
TYRE CHANGING TOOLS

60G-06-007

3)
Continue to lift up the bonnet until it is high

enough to support with the prop rod.

Make sure the bonnet Is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
60G-06-008

To use the cup holder, pull it out fully. After

using the holder, push it back in.

Do not use the cup holder to hold cups

containing hot liquids, or objects other

than cups. Objects in the cup holder

may be thrown about during a sudden

stop or impact, and could cause

personal injury.
60G-06-009

The jack, wheel wrench and jack crank are

stowed in the luggage compartment behind

the rear seat.

To remove the jack, turn its shaft

counterclockwise and pull the jack out of the

storage bracket. To stow the jack, place it in

the storage bracket and turn the shaft

clockwise until the jack is securely held in

place.

6-7
60

60G-74E
OTHER CONTROLS AND EQUIPMENT

LUGGAGE COMPARTMENT TRIM TRUNK (BOOT) LIGHT (if equipped)

Luggage or other cargo placed in the luggage

compartment are hidden from view by a

luggage compartment trim.

Do not carry items on top of the

luggage compartment trim, even if they

are small and light. Objects on top of

the trim could be thrown about In an

accident, causing injury, or could

obstruct the driver's rear view.

60G-06-010
6OG-O6-O11

The jack should be used only to change

wheels. It is important to read the

jacking Instructions in the

EMERGENCY SERVICE section of this

manual before attempting to use the

jack.
When you open the trunk (boot) lid, the trunk

(boot) light comes on and remains on as

long as you keep the lid open.

Do not leave the boot (trunk) lid open

for a long time, or the battery will

discharge.

After using the jack, jack crank and

wheel wrench, be sure to stow them

securely or they can cause injury if an

accident occurs.

61

6-8

S0G-74E
OPERATING YOUR VEHICLE

OPERATING YOUR VEHICLE

Exhaust Gas Warning 7-1

Daily Inspection Checklist 7-1

Starting the Engine 7-2

Using the Transmission 7-3

Braking 7-4

Running-in 7-5

Catalytic Converter (if equipped) 7-6

Improving Fuel Economy 7-7

Trailer Towing 7-7

OPERATING YOUR VECHILE

60G-74E

EXHAUST GAS WARNING
DAILY INSPECTION CHECKLIST

60G-07-001E

Avoid breathing exhaust gases.

Exhaust gases contain carbon

monoxide, a potentially lethal gas that

is colourless and odourless. Since

carbon monoxide is difficult to detect

by itself, be sure to take the following

precautions to help prevent carbon

monoxide from entering your vehicle.

• Do not leave the engine running in

garages or other confined areas.

• Do not park with the engine running

for a long period of time, even in an

open area. If it is necessary to sit for

a short time in a parked vehicle <=>
with the engine running, make sure

the air intake lever is set to "FRESH

AIR" and the fan is at high speed.

To allow proper operation of your

vehicle's ventilation system, keep

the air inlet grille in front of the

windscreen clear of snow, leaves, or

other obstructions at all times.

Keep the exhaust tailpipe area clear

of snow and other material to help

reduce the buildup of exhaust gases

under the vehicle.This is particularly

important when parked in blizzard

conditions.

Have the exhaust system inspected

periodically for damage and leaks.

Any damage or leaks should be

repaired immediately.

7-1
70F-05-007

Before driving:

1) Make sure that windows, mirrors, lights,

and reflectors are clean and unobstructed.

2) Check the tyres.

3) Look for fluid and oil leaks.

NOTE:

It is normal for water to drip from the air

conditioning system after use.

4) Adjust the seat/head restraint.

5) Check the brake pedal and the parking

brake lever.

6) Adjust the mirrors.

7) Make sure that you and passengers have

properly fastened your seat belts.

8) Make sure that all warning lights come on

as the key is turned to the "ON" or "START'

position.

9) Check all gauges.

10) Make sure that the brake fluid level

warning light is off when the parking brake

is released with the ignition switch in "ON"

position.

66
65

60G-74E
OPERATING YOUR VEHICLE

CATALYTIC CONVERTER

(if equipped)

70F-05-005

The purpose of the catalytic converter installed

on your vehicle is to convert exhaust pollutants

to harmless water vapour, carbon dioxide, and

nitrogen. Use of leaded fuel in vehicles

equipped with catalytic converters is

prohibited, because lead deactivates the

pollutant-reducing components of the catalyst

system.

It is very important to keep the engine properly

tuned. Engine misfiring, which can result from

an improperly tuned engine, may cause

overheating of the catalyst. This may result in

permanent heat damage to the catalyst and

other vehicle components.
CAUTION

To minimize the possibility of catalyst

or other vehicle damage:

• Maintain the engine in the proper

operating condition.

• In the event of an engine

malfunction, particularly one

involving engine misfire or other

apparent loss of performance, have

the vehicle serviced promptly.

• Do not turn off the engine or

interrupt the ignition when the

transmission is in gear and the

vehicle is in motion.

• Do not try to start the engine by

pushing or towing the vehicle, or

coasting down a hill.

• Do not idle the engine with any spark

plug wires disconnected or

removed, such as during diagnostic

testing.

• Do not idle the vehicle for prolonged

periods if idling seems rough or

there are other malfunctions.

• Do not allow the fuel tank to get near

the empty level.
60Q-07-002E

Be careful where you park and drive;

the catalytic converter and other

exhaust components can get very hot.

As with any vehicle, do not park or

operate this vehicle in areas where

combustible materials such as dry

grass or leaves can come in contact

with a hot exhaust system.

7-6

OPERATING YOUR VECHILE

60G-74E

IMPROVING FUEL ECONOMY

The following instructions will help you improve

fuel economy.

Avoid excessive idling:

If you are to wait for more than a minute while

you are parked, stop the engine and start it

again later. When warming up a cold engine,

allow the engine to idle until the temperature

gauge pointer comes up to the "C" position. In

this position, the engine is sufficiently warm

for starting off.

Avoid "fast" starts:

Fast starts away from lights or stop signs will

consume fuel unnecessarily and shorten

engine life. Start off slowly.

Avoid unnecessary stops:

Avoid unnecessary deceleration and stopping.

Try to maintain a slow, steady speed whenever

possible. Slowing down and then accelerating

again uses more fuel.

Keep a steady cruising speed:

Keep as constant a speed as road and traffic

conditions will permit.
Air Outlet side

(Facing up)

60G-09-010

Keep the air cleaner clean:

A dirty air cleaner will cause the carburation

system to supply too much fuel to the engine

for the amount of air being supplied. The result

is waste of fuel due to incomplete combustion.

Keep weight to a minimum:

The heavier the load, the more fuel the vehicle

consumes. Take out any luggage or cargo

when it is not necessary.

Keep tyre pressures correct:

Under-inflation of the tyres can waste fuel due

to increased running resistance of the tyres.

Keep your tyres inflated to the correct pressure

shown on the label on the driver's side door

or door lock pillar.
TRAILER TOWING

Your MARUTI was originally designed to carry

people and a normal amount of cargo, not to

tow a trailer. Maruti does not recommend you

use your vehicle to tow a trailer.Towing a trailer

can adversely affect handling, durability, and

fuel economy.

7-7

72
71

60G-74E
INSPECTION AND MAINTENANCE

70F-07-060

For windshield wipers:

1. Hold the wiper arm away from the

window.
72F-09-008

2. Squeeze lock lever (A) towards wiper arms

(B) and remove the wiper frame from the

arm as shown.

113

9-30

60G-74E
EMERGENCY SERVICE

EMERGENCY SERVICE

Jacking Instructions 10-1

Jump Starting Instructions 10-2

Towing 10-4

Emergency Remedies 10-4

Warning Triangle 10-5

115

60G-74E
INSPECTION AND MAINTENANCE

70F-07-060

For windshield wipers:

1. Hold the wiper arm away from the

window.
72F-09-008

2. Squeeze lock lever (A) towards wiper arms

(B) and remove the wiper frame from the

arm as shown.

113

9-30

60G-74E
EMERGENCY SERVICE

EMERGENCY SERVICE

Jacking Instructions 10-1

Jump Starting Instructions 10-2

Towing 10-4

Emergency Remedies 10-4

Warning Triangle 10-5

115