battery SUZUKI CELERIO 2016 Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2016, Model line: CELERIO, Model: SUZUKI CELERIO 2016Pages: 201, PDF Size: 5.82 MB
Page 15 of 201
0-3
76MH1-74E
VEHICLE DETAILS
MODEL CHASSIS NO. ENGINE NO. KEY NO.DATE OFDELIVERYODOMETERREADING (KM)
BATTERY
MAKESR.NO. BATCH CODE
OWNER’S NAME & ADDRESS ________________________________________________________________________________
_________________________________________________________________________________________________________
______________________________________________________________________TEL.NO. ____________________________
ADRESS/STAMP OF SELLING DEALER SELLING DEALER CODE
SHOWROOM
WORKSHOP IMPORTANT INFORMATION TO CUSTOMER
Dear Customer,
For any assistance with regard to our product, please contact General Manager/Works Manager at any of our Dealer or Autho-rised Service Station. For additional enquiry you may contact ourRegional Office or Service Department. The Addresses andPhone nos. are given in Service Network section of this Manual.
4
Page 26 of 201
2-4
BEFORE DRIVING
76MH1-74E
76MH1-74E
Ta i l g a t e
76MH0A086
(1) Driver’s door lock (2) Tailgate lock (3) Tailgate handle
If your vehicle is equipped with the cen-tral door locking system, you can lock orunlock the tailgate by using the key in the driver’s door lock (1).
If your vehicle is not equipped with thecentral door locking system, you can lock or unlock the tailgate by using thekey in the tailgate lock (2).
To open the tailgate, pull up the tailgatehandle (3) and lift the tailgate.
If you cannot unlatch the tailgate by pulling up the tailgate handle (3) due to a dis- charged battery or malfunction, follow the procedures below to unlatch the tailgatefrom inside the vehicle. 1) Remove the luggage compartmentcover (if equipped) and fold the rear seat forward for easier access. Refer to “Folding Rear Seats” section for details on how to fold the rear seat forward.
76MH0A099
2) Remove the trim (5) of the tailgate. Push center of the clips (4) and pullthem out. Then, remove the trim (5).
76MH0A137
3) To unlock the tailgate lock, pull the lockplate (6) up. To open the tailgate, pushthe emergency lever (7) sideways. Thetailgate will be latched again by simply closing the tailgate.
If the tailgate cannot be unlatched by pull-ing up the tailgate handle (3), have the vehicle inspected by your MARUTISUZUKI dealer.
WA R N I N G
Always make sure that the tailgate is closed and latched securely. Com- pletely closing the tailgate helps pre-vent occupants from being thrown from the vehicle in the event of an accident. Completely closing it alsohelps keep exhaust gases from enter- ing the vehicle.
(3)
(1)
(2)
EXAMPLE
(5)
(4)
CAUTION
Make sure there is no one near the tailgate when pushing open the tail- gate from inside the vehicle. To avoid injury, do not use your fin-ger to push the emergency lever.
(6)
(7)
15
Page 28 of 201
2-6
BEFORE DRIVING
76MH1-74E
76MH1-74E
Panic alarm function (if equipped)This function is to get the attention of oth- ers. Push both of the “LOCK” button (1) and “UNLOCK” button (2) for more than 3 sec-onds. The turn signal lights will blink for about 27.5 seconds. Also, the siren will sound for about 27.5 seconds at the sametime. To cancel the panic alarm, press any but- ton (LOCK or UNLOCK). You can also turnthe ignition switch to the “ON” position to cancel the panic alarm.
NOTE: The panic alarm function will not activate when the key is in the ignition switch.
Replacement of the Battery If the transmitter becomes unreliable, replace the battery.
To replace the battery of the transmitter:
68LM248
1) Remove the screw (1), and open thetransmitter cover.2) Remove the transmitter (2).
68LM249
(3) Lithium disc type battery:CR1616 or equivalent
3) Put the edge of a flat blade screwdriverin the slot of the transmitter (2) and pry it open.4) Replace the battery (3) so its + terminalfaces the “+” mark of the transmitter.5) Close the transmitter and install it intothe transmitter holder.6) Close the transmitter cover, install andtighten the screw (1).7) Make sure the door locks can be oper-ated with the transmitter.8) Dispose of the used battery properlyaccording to applicable rules or regula- tions. Do not dispose of lithium batter- ies with ordinary household trash.
NOTICE
The transmitter is a sensitive elec-tronic instrument. To avoid damagingthe transmitter: • Do not expose it to impacts, mois-ture or high temperature such as by leaving it on the dashboard under direct sunlight.• Keep the transmitter away frommagnetic objects such as a televi-sion.• Do not tamper with internal parts.
(1)
(2)
(2)
(3)
WA R N I N G
Swallowing a lithium battery may cause serious internal injury. Do notallow anyone to swallow a lithium battery. Keep lithium batteries away from children and pets. If swallowed,contact a physician immediately.
NOTICE
The transmitter is a sensitive elec- tronic instrument. To avoid damaging it, do not expose it to dust or mois-ture or tamper with internal parts.
17
Page 30 of 201
2-8
BEFORE DRIVING
76MH1-74E
76MH1-74E
Without tachometer
76MH0B002
NOTE: • To prevent the alarm from being acci-dentally triggered, avoid arming it while anyone remains inside the vehicle. The alarm will be triggered if any person inside opens the door or engine hood, orswings the vehicle (if the shock sensor is in the enabled state).• The security system is not armed whenall doors are locked using the key fromoutside, or using the door lock knobs or the central door locking switch frominside.• If any door is not operated within approx-imately 30 seconds after the doors havebeen unlocked using the keyless entry system transmitter, the doors are auto-matically locked again. When the doors are locked, the security system will be
armed in about 5 seconds if the system is in the enabled state.• If the security system indicator (1) blinkswhen the ignition switch is in the “ON”position, there may be something wrong with the security system. Ask your MAR-UTI SUZUKI dealer to inspect the sys- tem.
How to disarm the security systemSimply unlock the doors using the keyless entry system transmitter. The security sys-tem indicator will go out, indicating that the security system is disarmed.
How to stop the alarm Should the alarm be triggered accidentally, unlock the doors using the keyless entrysystem transmitter, or insert the key in the ignition switch and turn it to “ON” position. The alarm will then stop.
NOTE: • Even after the alarm has stopped, if youlock the doors using the keyless entry system transmitter, the security system will be rearmed with a delay of about 5seconds.• If you disconnect the battery while thesecurity system is in the armed conditionor the alarm is actually in operation, the alarm will be re-triggered when the bat- tery is then reconnected.• Even after the alarm has stopped at theend of the predetermined operation time,it will be triggered again if any of thedoors or engine hood is opened, or the
vehicle feels a shock (if the shock sen- sor is in the enabled state), without dis- arming the security system.
Checking whether the alarm has beentriggered during parkingIf the alarm was triggered and you then turn the ignition switch to “ON” position, the security system indicator will blink rapidlyfor about 8 seconds and a buzzer will beep 4 times during this period. If this happens, check whether the vehicle has been bro-ken into while you were away from it.
Enabling and disabling the security system The security system can be either enabled or disabled.
When enabled If any of the doors are opened withoutunlocking by the keyless entry system transmitter, all turn signal lights start to blink and the interior buzzer beeps inter-mittently. After 5 seconds, the siren will sound for about 27.5 seconds. The secu- rity system indicator continues to blinkduring this time. If the engine hood is opened, all turn sig-nal lights blink, and the siren sounds forabout 27.5 seconds. The security sys- tem indicator continues to blink during this time.
(If the shock sensor is in the enabled state) If the vehicle feels a shock, the sirensounds for about 2 seconds (pre-warn- ing). If the vehicle continues to feel a
(1)
19
Page 38 of 201
2-16
BEFORE DRIVING
76MH1-74E
76MH1-74E
65D199
Lap-Shoulder Belt
Emergency Locking Retractor (ELR) The seat belt has an emergency locking retractor (ELR), which is designed to lock the seat belt only during a sudden stop orimpact. It also may lock if you pull the belt across your body very quickly. If this hap- pens, let the belt go back to unlock it, thenpull the belt across your body more slowly.
WA R N I N G
(Continued)• Pregnant women should use seatbelts, although specific recommen- dations about driving should be made by the woman’s medical advi-sor. Remember that the lap portion of the belt should be worn as low as possible across the hips, asshown in the diagram.• Do not wear your seat belt overhard or breakable objects in yourpockets or on your clothing. If an accident occurs, objects such as glasses, pens, etc. under the seatbelt can cause injury.(Continued)
as low as possible across the hips
WA R N I N G
(Continued)• Never use the same seat belt onmore than one occupant and never attach a seat belt over an infant orchild being held on an occupant’s lap. Such seat belt use could cause serious injury in the event of anaccident.• Periodically inspect seat beltassemblies for excessive wear anddamage. Seat belts should be replaced if webbing becomes frayed, contaminated, or damagedin any way. It is essential to replace the entire seat belt assembly after it has been worn in a severe impact,even if damage to the assembly is not obvious.• Children age 12 and under shouldride properly restrained in the rearseat.• Infants and small children shouldnever be transported unless theyare properly restrained. Restraint systems for infants and small chil-dren can be purchased locally andshould be used. Make sure that the system you purchase meets appli- cable safety standards. Read andfollow all the directions provided by the manufacturer.• For children, if the shoulder belt irri-tates the neck or face, move thechild closer to the center of the vehicle.(Continued)
WA R N I N G
(Continued) • Avoid contamination of seat beltwebbing by polishes, oils, chemi-cals, and particularly battery acid.Cleaning may safely be carried out using mild soap and water.• Do not insert any items such ascoins, clips, etc. into the seat beltbuckles, and be careful not to spill liquids into these parts. If foreignmaterials get into a seat belt buckle, the seat belt may not work properly.• All seatbacks should always be inan upright position when driving,or seat belt effectiveness may bereduced. Seat belts are designed to offer maximum protection whenseatbacks are in the upright posi- tion.
27
Page 49 of 201
2-27
BEFORE DRIVING
76MH1-74E
76MH1-74E
Note that even though your vehicle may be moderately damaged in a frontal collision,the collision may not have been severe enough to trigger the air bags to inflate. If your vehicle sustains ANY front-end dam-age, have the air bag system inspected by an authorized MARUTI SUZUKI dealer to ensure it is in proper working order.
Your vehicle is equipped with a diagnostic module which records information aboutthe air bag system if the air bags deploy ina crash. The module records informationabout overall system status, which sensorsactivated the deployment, and for a certain vehicle only, whether the driver’s seat belt was in use.
Servicing the air bag system If the air bags inflate, have the air bags andrelated components replaced by an autho- rized MARUTI SUZUKI dealer as soon as possible.
If your vehicle ever gets in deep water and the driver’s floor is submerged, the air bagcontroller could be damaged. If it does, have the air bag system inspected by theMARUTI SUZUKI dealer as soon as possi- ble.
Special procedures are required for servic- ing or replacing an air bag. For that reason, only an authorized MARUTI SUZUKI dealer should be allowed to service orreplace your air bags. Please remind any-
one who services your vehicle that it has air bags.
Service on or around air bag components or wiring must be performed only by an authorized MARUTI SUZUKI dealer.Improper service could result in unin- tended air bag deployment or could render the air bag inoperative. Either of these twoconditions may result in severe injury.
To prevent damage or unintended inflation of the air bag system, be sure the batteryis disconnected and the ignition switch hasbeen in the “LOCK” position for at least 90seconds before performing any electrical service work on your vehicle. Do not touch air bag system components or wires. Thewires are wrapped with yellow tape or yel- low tubing, and the couplers are yellow for easy identification.
Scrapping a vehicle that has an uninflated air bag can be hazardous. Ask your dealer,body repair shop or scrap yard for help with disposal.
38
Page 52 of 201
2-30
BEFORE DRIVING
76MH1-74E
76MH1-74E
To increase the brightness of the instru- ment panel lights, turn the brightness con- trol knob (1) clockwise.To reduce the brightness of the instrument panel lights, turn the brightness control knob (1) counterclockwise.
NOTE: • If you do not turn the brightness controlknob within about 5 seconds of activat-ing the brightness control display, thebrightness control display will be can- celed automatically.• When you reconnect the battery, thebrightness of the instrument panel lightswill be reinitialized. Readjust the bright- ness according to your preference.
Information Display
76MH0A032
with tachometer
76MH0A040
without tachometer
76MH0A041
(1) Trip meter selector knob (2) Indicator selector knob (3) Information display
When the ignition switch is in the “ON”position, the information display shows thefollowing information.
Display (A) Clock
Display (B) Fuel gauge
Display (C) Trip meter / Odometer / Fuel consumption / Driving range
Display (D) Gear position indicator (for Auto Gear Shift models)
Display (E) Thermometer (if equipped)
WA R N I N G
If you attempt to adjust the displaywhile driving, you could lose controlof the vehicle.
Do not attempt to adjust the displaywhile driving.
(2)
(1)EXAMPLE
(3)
(A) (E)
(B)
(C)
(D)
EXAMPLE
(3)
(A)
(B)(C)
EXAMPLE
41
Page 53 of 201
2-31
BEFORE DRIVING
76MH1-74E
76MH1-74E
ClockWhen the ignition switch is in the “ON” position, the display (A) shows the time.
To change the time indication: 1) Push the trip meter selector knob (1)and the indicator selector knob (2)together.2) To change the hour indication, turn theindicator selector knob (2) left or rightrepeatedly when the hour indicationblinks. To change the hour indication quickly, turn and hold the indicator selec- tor knob (2). To set the hour indication,push the indicator selector knob (2) and the minute indication will blink.3) To change the minute indication, turn theindicator selector knob (2) left or rightrepeatedly when the minute indication blinks. To change the minute indicationquickly, turn and hold the indicator selec- tor knob (2). To set the minute indication, push the indicator selector knob (2).
NOTE: When you reconnect the negative (–) ter-minal to the battery, the clock indication will be reinitialized. Change the indication again to your preference.
Fuel GaugeWhen the ignition switch is in the “ON”position, the display (B) shows the fuel gauge.
Refer to “Fuel Gauge” in this section.
Trip meter / Odometer / Fuel con-
sumption / Driving rangeWhen the ignition switch is in the “ON” position, the display (C) shows one of the following indications, trip meter A, tripmeter B, odometer, instantaneous fuel consumption, average fuel consumption or driving range.
To switch the display indication (C), push the trip meter selector knob (1) or the indi-cator selector knob (2) quickly.
76MH0A045
WA R N I N G
If you attempt to adjust the display while driving, you could lose control of the vehicle.
Do not attempt to adjust the displaywhile driving.
Push the trip meter selector knob (1).
Push the indicator selector knob (2).
(a)
(b)
(c)
(d)
(e)
(f)
EXAMPLE
42
Page 54 of 201
2-32
BEFORE DRIVING
76MH1-74E
76MH1-74E
(a) Trip meter A (b) Trip meter B (c) Odometer(d) Instantaneous fuel consumption (e) Average fuel consumption (f) Driving range
NOTE:• Indications will change when you pushand release a knob.• The display shows estimated values.Indications may not be the same as actual values.Trip meter The trip meter can be used to measure the distance traveled on short trips or between fuel stops.You can use the trip meter A or trip meter B independently.
To reset the trip meter to zero, push and hold the trip meter selector knob (1) for a while when the display shows the tripmeter.
NOTE: The indicated maximum value of the trip meter is 9999.9. When you run past the
maximum value, the indicated value willreturn to 0.0.
Odometer The odometer records the total distance the vehicle has been driven.
Instantaneous Fuel ConsumptionThe display shows the value of instanta- neous fuel consumption only when the vehi- cle is moving.
NOTE:• The display does not show the valueunless the vehicle is moving.• The indicated maximum value of instanta-neous fuel consumption is 30. No more than 30 will be indicated on the displayeven if the actual instantaneous fuel con-sumption is higher.• The indication on the display may bedelayed if fuel consumption is greatly affected by driving conditions.• The display shows estimated values. Indi-cations may not be the same as actual values.• You can change the units that instanta-neous fuel consumption is displayed in.Refer to “Average fuel consumption” in this section.
Average fuel consumptionIf you selected average fuel consumptionthe last time you drove the vehicle, the dis- play shows the last value of average fuelconsumption from previous driving when the ignition switch is turned to the “ON”position. Unless you reset the value of aver- age fuel consumption, the display indicates the value of average fuel consumption which includes average fuel consumptionduring previous driving.
To reset the average fuel consumption to zero, push and hold the indicator selector knob (2) for a while when the display shows the average fuel consumption.
NOTE: When you reset the indication or reconnectthe negative (–) terminal to the battery, the value of average fuel consumption will be shown after driving for a while.
To change the unit of average fuel con- sumption, while pushing and holding thetrip meter selector knob (1), turn the indi- cator selector knob (2).
76MH0A046
WA R N I N G
If you attempt to adjust the display while driving, you could lose controlof the vehicle.
Do not attempt to adjust the displaywhile driving.
NOTICE
Keep track of your odometer reading and check the maintenance scheduleregularly for required services. Increased wear or damage to certain parts can result from failure to performrequired services at the proper mile-age intervals.
EXAMPLE
(Initial setting)
43
Page 55 of 201
2-33
BEFORE DRIVING
76MH1-74E
76MH1-74E
NOTE:• When you change the units that averagefuel consumption is displayed in, the instantaneous fuel consumption units will be changed automatically.• When you reconnect the negative (–) ter-minal to the battery, the unit of the aver-age fuel consumption will be reinitialized.Change the unit again to your preference.
Driving rangeIf you selected driving range the last timeyou drove the vehicle, the display indicates“---” for a few seconds and then indicatesthe current driving range when the ignitionswitch is turned to the “ON” position. The driving range shown in the display is the approximate distance you can drive untilthe fuel gauge indicates “E”, based on cur-rent driving conditions.
When the low fuel warning light comes on, the display “---” will appear.
If the low fuel warning light comes on, fill thefuel tank immediately regardless of the valueof driving range shown in the display.
As the driving range after refueling is calcu-lated based on the most recent driving con-dition, the value is different each time you refuel.
NOTE: • If you refuel when the ignition switch is inthe “ON” position, the driving range may not indicate the correct value.• When you reconnect the negative (–) ter-minal to the battery, the value of drivingrange will be shown after driving for awhile.
Gear position indicator (for Auto
Gear Shift models)
76MH0A044
When the ignition switch is in the “ON” position, the display (D) indicates the gearposition. For details on how to use the transaxle, refer to “Using the Transaxle” in the“OPERATING YOUR VEHICLE” section.
Thermometer (if equipped)When the ignition switch is in the “ON”position, the display (E) shows the ther-mometer. The thermometer indicates the outside temperature.
76MH0A042
If the outside temperature nears freezing, the mark (g) will appear on the display.
NOTE:• The outside temperature indication is notthe actual outside temperature when driv- ing at low speed, or when stopped.• If there is something wrong with the ther-mometer, or just after the ignition switchis turned to the “ON” position, the display may not indicate the outside temperature.
When the display (C) shows the driving range, you can change the unit of tempera-ture. To change the unit of temperature, while pushing and holding the trip meter selectorknob (1), turn the indicator selector knob (2).
76MH0A043
NOTE: When you reconnect the negative (–) ter- minal to the battery, the unit of temperaturewill be reinitialized. Change the unit again to your preference.
EXAMPLE
(g)EXAMPLE
EXAMPLE
(Initial setting)
44