ECO mode SUZUKI CELERIO 2021 Owners Manual

0-2
76MH1-74E
55KS0-74E
IMPORTANT
WARNING/ CAUTION/NOTICE/NOTE Please read this manual and follow itsinstructions carefully. To emphasize spe-cial information, the symbol and thewords WARNING, CAUTION, NOTICEand NOTE have special meanings. Payparticular attention to messages high-lighted by these signal words:
NOTE: Indicates special information to makemaintenance easier or instructions clearer.
75F135
The circle with a slash in this manualmeans “Don’t do this” or “Don’t let this hap-pen”.
MODIFICATION WARNING
WARNING
Indicates a potential hazard thatcould result in death or seriousinjury.
CAUTION
Indicates a potential hazard thatcould result in minor or moderateinjury.
NOTICE
Indicates a potential hazard thatcould result in vehicle damage.
WARNING
Do not modify your vehicle. Modifica-tion could adversely affect safety,handling, performance, or durabilityand may violate governmental regula-tions. In addition, damage or perfor-mance problems resulting frommodification may not be coveredunder warranty.
NOTICE
Improper installation of mobile com-munication equipment such as cellu-lar telephones or CB (Citizen’s Band)radios may cause electronic interfer-ence with your vehicle’s ignition sys-tem, resulting in vehicle performanceproblems. Consult your MARUTISUZUKI dealer for advice on install-ing such mobile communicationequipment.
WARNING
Severe damage may be caused bythe use of either poor quality fueland/or lubricants not recommendedby MARUTI SUZUKI.
3

0-6
76MH1-74E
55KS0-74E
11) Any vehicle which has been used for purposes other thanwhat it was designed for.
12) Any damage or deterioration caused by industrial pollutionand bird droppings.
13) Insignificant defects which do not affect the function of thevehicle including without limitation, sound, vibration and fluid seep.
14) Any natural wear and tear including without limitation, agingetc.
15) Installation and usage of domestic LPG gas/LPG Cylinder.
16) V-belts, hoses and gas leaks (For Maruti Suzuki AC vehicle).
17) Any vehicle retrofitted with LPG/CNG kits.
(5) Extent of Warranty:This warranty is the entire written warranty given by Maruti Suzuki
for Maruti Suzuki vehicles and no dealer or its or his agent or
employee is authorised to extend or enlarge this warranty and no
dealer or its or his agent or employee is authorised to make any
oral warranty on Maruti Suzuki’s behalf.
Maruti Suzuki reserves the right to add any improvements or
change the design of any model at any time with no obligation to
make the same changes on units previously sold.
(6) Warranty Service:To obtain warranty service, the complete vehicle must be pre-
sented at the owner’s expenses to any authorised Maruti Suzuki
dealer.
(7) Owner’s Warranty ResponsibIlities:It is responsibility of each owner to:
– Make certain that the warranty registration/PDl card was
completed at the time of delivery of the vehicle;
– Have performed, at his own expenses, by an Maruti Suzuki
authorised dealer/service station all the service inspections
specified in the Maruti Suzuki “Owner’s Manual and Service
Booklet and maintain adequate proof that such service
inspections have been performed.
– Make certain that the Maruti Suzuki authorised dealer/ser-
vice station performing the service inspection has certified
the work on the “Maintenance Service Record” page in the
“Owner’s Manual and Service Booklet and
– Present the Maruti Suzuki “Owner’s Manual and Service
Booklet to the authorised Maruti Suzuki dealer whenever
requesting service inspections or warranty service.
If the “Owner’s Manual and Service Booklet should be lost or
destroyed the owner should consult the authorised Maruti Suzuki
dealer from whom the vehicle was purchased for instructions con-
cerning replacement of the “Owner’s Manual and Service Booklet.
(8) Disclaimer of Consequential Damage:Maruti Suzuki assumes no responsibility for loss of vehicle, loss of
time, inconvenience or any other indirect incidental or consequen-
tial damage resulting from the vehicle not being available to the
owner because of any defect covered by this warranty.
(9) Change of OwnerEven if ownership of the vehicle changes, the remaining warranty
period is effective for the new owner.
7

2-5
BEFORE DRIVING
76MH1-74E
76MH1-74E
Keyless Entry System
Transmitter (if equipped)
76MS011
(1) “LOCK” button (2) “UNLOCK” button
You can lock or unlock all doors (includingthe tailgate) simultaneously by operating the transmitter near the vehicle.
To lock all doors, push the “LOCK” but-ton (1) once. To unlock only the driver’s door, push the“UNLOCK” button (2) once. To unlock other doors, push the“UNLOCK” button (2) once again.
NOTE: You can switch the function that unlocks alldoors from twice operations to once opera- tion, and vice versa, via the setting modeof the information display. For details onhow to use the information display, refer to“Information Display” in this section.
The turn signal lights will flash once and the siren (if your vehicle is equipped with the security system) will sound once whenthe doors are locked.
When the doors are unlocked: The turn signal lights will flash twice andthe siren (if your vehicle is equipped withthe security system) will sound twice. If the interior light switch is in the“DOOR” position, the interior light willturn on for about 15 seconds and thenfade out. If you insert the key into the ignition switch during this time, the light will start to fade out immediately.
Be sure the doors are locked after youoperate the “LOCK” button. If no door isopened within about 30 seconds after the “UNLOCK” button is operated, the doors will automatically lock again.
NOTE: (For models with security system)• If you lock the doors using the transmit-ter when the engine hood is open, thesiren will sound 3 times to remind you.• If the security system was triggered dueto an unauthorized entry into the vehicleand then you unlock the doors using thetransmitter, the siren will sound 4 times to remind you. If this happens, check whether your vehicle has been brokeninto while you were away from it.• Once you push both of the “LOCK” but-ton (1) and “UNLOCK” button (2), thenyou push one of the buttons within 5 sec-
onds, the siren will not sound. However, If you push one of the buttons twice within 5 seconds, or push one of the but-tons 5 seconds later, the siren willsound.• You can set whether the siren soundswhen locking or unlocking the door(s) via the setting mode of the information dis- play. For details on how to use the infor-mation display, refer to “InformationDisplay” in this section.
NOTE: • The maximum operating distance of thekeyless entry system transmitter is about 15 m (48 ft.), but this can vary depending on the surroundings, especially near other transmitting devices such as radiotowers or CB (Citizen’s Band) radios.• The door locks cannot be operated withthe transmitter if the ignition key isinserted in the ignition switch.• If any door is open, you cannot lock thedoor by operating the transmitter, how-ever unlock the door.• If you lose one of the transmitters, askyour MARUTI SUZUKI dealer as soonas possible for a replacement. Be sure to have your dealer program the new transmitter code in your vehicle’s mem-ory so that the old code is erased.
(1)
(2)
16

2-7
BEFORE DRIVING
76MH1-74E
76MH1-74E
Security System (if equipped)
The security system is armed in about 5 seconds after you lock all doors (includingthe tailgate) by using the keyless entry sys- tem transmitter. Once the system is armed, any attempt toopen a door by using any other means (*) than the keyless entry system transmitter, or open the engine hood, will cause thealarm to be triggered. * These means include the following:–The key – The lock knob on a door – The central door locking switch
Also, in case that you have set the shocksensor to enabled state and set sensitivity of the pre-warning function and full blastwarning function to a level other than 0, the alarm will be triggered if any attempt to tamper with the vehicle. The shock sensorcan be selected enabled or disabled state, and sensitivity of each warning can be adjusted as desired. To set the shock sen-sor, ask your MARUTI SUZUKI dealer or use the setting mode of the information display.
NOTE: • The default setting of the shock sensoris in the disabled state. Set to the enabled state and adjust sensitivity of each warning according to your prefer- ence. For details on how to use the infor-mation display, refer to “Information Display” in this section.• Your dealer may have already set theshock sensor of the vehicle to theenabled state before you purchase it. Consult your dealer for further informa-tion.
NOTE:• The security system generates alarmswhen any of the predetermined condi-tions is met. However, the system doesnot have any function of blocking unau- thorized entry into the vehicle.• Always use the keyless entry systemtransmitter to unlock the doors when thesecurity system has been armed. Using a key instead will trigger the alarm.• If a person who does not know the secu-rity system is going to drive the vehicle,we recommend you explain the systemand its operation to the person, or dis- able the system beforehand. Mistakenly triggering the alarm may cause a nui-sance to others.• Even if the security system is armed,you should still be careful to guardagainst theft. Do not leave money or things of value in the vehicle.
How to arm the security system
(when enabled)Lock all doors (including the tailgate) using the keyless entry system transmitter. Thesecurity system indicator (1) will start blink- ing rapidly, and the security system will be armed in about 5 seconds.While the system is being armed, the indi- cator continues to blink at intervals of approximately 2 seconds.
With tachometer
76MH0B001
(1)
18

2-9
BEFORE DRIVING
76MH1-74E
76MH1-74E
shock, all turn signal lights start to blink and the interior buzzer beeps intermit- tently. After 5 seconds, the siren willsound for about 27.5 seconds (full blast warning). The security system indicator continues to blink during this time.
NOTE:If you set the full blast warning sensitivityhigher than the pre-warning sensitivity inthe setting mode of the information display,or the vehicle feels such shock as to beable to trigger the full blast warning, the full blast warning will be triggered preferen- tially. In this case, the pre-warning will notbe triggered.
When disabled When the system is disabled, it stays dis- armed even if you perform any system arming operation.
How to switch the state of the security systemWhen the security system has beenalready disarmed, you can switch the sys-tem from the enabled state to the disabledstate, and vice versa, using the following method.
1) Sit in the driver

2-10
BEFORE DRIVING
76MH1-74E
76MH1-74E
4) Push the lock end (4) (forward end) ofthe central door locking switch (5), and then push the unlock end (6) (backwardend). Repeat this operation 3 times.
Every time you perform the series of theabove steps, the state of the security sys- tem changes from the currently selected one to the other. You can check whetherthe system is enabled or disabled by the number of interior buzzer beeps at the end of the procedure as follows.
If you cannot complete the operations instep 3) and 4) within 15 seconds cor- rectly, the state of the security systemwill not change and the interior buzzer does not beep. Perform the procedure again from the beginning.
NOTE: You can also switch the security systemfrom the enabled state to the disabled state, and vice versa, via the setting mode of the information display. For details onhow to use the information display, refer to“Information Display” in this section.
Windows
Manual Window Control
(if equipped)
60G010
Raise or lower the door windows by turning the handle located on the door panel.
Electric Window Controls
(if equipped)The electric windows can only be operated when the ignition switch is in the “ON” posi- tion.
Driver’s door
76MH0A022
The driver’s door has a switch (1) to oper- ate the driver’s window, and a switch (2) tooperate the front passenger’s window or there are switches (4), (3), to operate the rear left and right passenger windows,respectively.
Passenger’s door
76MH0A023
The passenger’s door has a switch (5) to operate that passenger’s window.
81A009
System state Number of beeps
DisabledOnce
Enabled 4 times
EXAMPLE
(1)(2)
(3)
(4)
EXAMPLE
(5)EXAMPLE
CLOSE
OPEN
21

2-27
BEFORE DRIVING
76MH1-74E
76MH1-74E
Note that even though your vehicle may be moderately damaged in a frontal collision,the collision may not have been severe enough to trigger the air bags to inflate. If your vehicle sustains ANY front-end dam-age, have the air bag system inspected by an authorized MARUTI SUZUKI dealer to ensure it is in proper working order.
Your vehicle is equipped with a diagnostic module which records information aboutthe air bag system if the air bags deploy ina crash. The module records informationabout overall system status, which sensorsactivated the deployment, and for a certain vehicle only, whether the driver’s seat belt was in use.
Servicing the air bag system If the air bags inflate, have the air bags andrelated components replaced by an autho- rized MARUTI SUZUKI dealer as soon as possible.
If your vehicle ever gets in deep water and the driver’s floor is submerged, the air bagcontroller could be damaged. If it does, have the air bag system inspected by theMARUTI SUZUKI dealer as soon as possi- ble.
Special procedures are required for servic- ing or replacing an air bag. For that reason, only an authorized MARUTI SUZUKI dealer should be allowed to service orreplace your air bags. Please remind any-
one who services your vehicle that it has air bags.
Service on or around air bag components or wiring must be performed only by an authorized MARUTI SUZUKI dealer.Improper service could result in unin- tended air bag deployment or could render the air bag inoperative. Either of these twoconditions may result in severe injury.
To prevent damage or unintended inflation of the air bag system, be sure the batteryis disconnected and the ignition switch hasbeen in the “LOCK” position for at least 90seconds before performing any electrical service work on your vehicle. Do not touch air bag system components or wires. Thewires are wrapped with yellow tape or yel- low tubing, and the couplers are yellow for easy identification.
Scrapping a vehicle that has an uninflated air bag can be hazardous. Ask your dealer,body repair shop or scrap yard for help with disposal.
38

2-30
BEFORE DRIVING
76MH1-74E
76MH1-74E
To increase the brightness of the instru- ment panel lights, turn the brightness con- trol knob (1) clockwise.To reduce the brightness of the instrument panel lights, turn the brightness control knob (1) counterclockwise.
NOTE: • If you do not turn the brightness controlknob within about 5 seconds of activat-ing the brightness control display, thebrightness control display will be can- celed automatically.• When you reconnect the battery, thebrightness of the instrument panel lightswill be reinitialized. Readjust the bright- ness according to your preference.
Information Display
76MH0A032
with tachometer
76MH0A040
without tachometer
76MH0A041
(1) Trip meter selector knob (2) Indicator selector knob (3) Information display
When the ignition switch is in the “ON”position, the information display shows thefollowing information.
Display (A) Clock
Display (B) Fuel gauge
Display (C) Trip meter / Odometer / Fuel consumption / Driving range
Display (D) Gear position indicator (for Auto Gear Shift models)
Display (E) Thermometer (if equipped)
WA R N I N G
If you attempt to adjust the displaywhile driving, you could lose controlof the vehicle.
Do not attempt to adjust the displaywhile driving.
(2)
(1)EXAMPLE
(3)
(A) (E)
(B)
(C)
(D)
EXAMPLE
(3)
(A)
(B)(C)
EXAMPLE
41

2-33
BEFORE DRIVING
76MH1-74E
76MH1-74E
NOTE:• When you change the units that averagefuel consumption is displayed in, the instantaneous fuel consumption units will be changed automatically.• When you reconnect the negative (–) ter-minal to the battery, the unit of the aver-age fuel consumption will be reinitialized.Change the unit again to your preference.
Driving rangeIf you selected driving range the last timeyou drove the vehicle, the display indicates“---” for a few seconds and then indicatesthe current driving range when the ignitionswitch is turned to the “ON” position. The driving range shown in the display is the approximate distance you can drive untilthe fuel gauge indicates “E”, based on cur-rent driving conditions.
When the low fuel warning light comes on, the display “---” will appear.
If the low fuel warning light comes on, fill thefuel tank immediately regardless of the valueof driving range shown in the display.
As the driving range after refueling is calcu-lated based on the most recent driving con-dition, the value is different each time you refuel.
NOTE: • If you refuel when the ignition switch is inthe “ON” position, the driving range may not indicate the correct value.• When you reconnect the negative (–) ter-minal to the battery, the value of drivingrange will be shown after driving for awhile.
Gear position indicator (for Auto
Gear Shift models)
76MH0A044
When the ignition switch is in the “ON” position, the display (D) indicates the gearposition. For details on how to use the transaxle, refer to “Using the Transaxle” in the“OPERATING YOUR VEHICLE” section.
Thermometer (if equipped)When the ignition switch is in the “ON”position, the display (E) shows the ther-mometer. The thermometer indicates the outside temperature.
76MH0A042
If the outside temperature nears freezing, the mark (g) will appear on the display.
NOTE:• The outside temperature indication is notthe actual outside temperature when driv- ing at low speed, or when stopped.• If there is something wrong with the ther-mometer, or just after the ignition switchis turned to the “ON” position, the display may not indicate the outside temperature.
When the display (C) shows the driving range, you can change the unit of tempera-ture. To change the unit of temperature, while pushing and holding the trip meter selectorknob (1), turn the indicator selector knob (2).
76MH0A043
NOTE: When you reconnect the negative (–) ter- minal to the battery, the unit of temperaturewill be reinitialized. Change the unit again to your preference.
EXAMPLE
(g)EXAMPLE
EXAMPLE
(Initial setting)
44

2-42
BEFORE DRIVING
76MH1-74E
76MH1-74E
NOTE: If the security system indicator blinks whenthe ignition switch is in the “ON” position, there may be something wrong with the security system. Ask your MARUTI SUZUKI dealer to inspect the system.
Depress Brake Pedal Indicator (if equipped)
76MH0A047
Refer to “Auto Gear Shift” in the “OPERAT- ING YOUR VEHICLE” section for details.
Fuel Filter Warning Light (For Diesel Engine Model)
60A541
This light comes on for several seconds when the ignition switch is turned to the “ON” position so you can check the light is working.
If the light comes on when driving, there is a possibility to have water in the fuel filter.Drain water as soon as possible. For
details of draining water, refer to “Fuel Fil- ter” in the “INSPECTION AND MAINTE- NANCE” section.
Glow Plug Indicator Light (For Diesel Engine Model)
60A543
If the coolant temperature is cool enough, this light comes on when the ignition switch is turned to the “ON” position and goes out when the glow plug is heated enough forengine starting.
Lighting Control Lever
65D611
Lighting Operation
60MK011
To turn the lights on or off, twist the knobon the end of the lever. There are threepositions:
OFF (1) All lights are off.
(2)Front position lights, tail lights, license plate light and instrument lights are on, but headlights are off.
(3)Front position lights, tail lights, licenseplate light, instrument lights and headlights are on.
WA R N I N G
To avoid possible injury, do not oper- ate controls by reaching through thesteering wheel.
(3)
(2)(1)
EXAMPLE
53