light SUZUKI GRAND VITARA 1999 2.G Service User Guide

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-15
AMBIENT TEMPERATURE WITHIN 30 ± 35C (85 ± 95F)
CONDITION
MANIFOLD
GAUGEMPa
(kg/cm2)
(psi)DETAILCAUSECORRECTION
LoHi
0.23 ± 0.35
(2.3 ± 3.5)
(33 ± 50)1.4 ± 1.75
(14 ± 17.5)
(200 ± 249)
Normal condition.ÐÐÐÐ
Negative
pressure0.5 ± 0.6
(5 ± 6)
(71.2 ± 85.3)

The low pressure side
reads a negative pressure,
and the high pressure side
reads an extremely low
pressure.

Presence of frost around
tubing to and from receiver /
dryer and expansion valve.
Dust particles or water
droplets are either stuck or
frozen inside expansion
valve, preventing the
refrigerant from flowing.
Clean expansion valve.
Replace it if it cannot be
cleaned.

Replace receiver / dryer.

Evacuate the A / C
system and recharge
with fresh refrigerant.
Normal:
0.23 ± 0.35
(2.3 ± 3.5)
(33 ± 50)

Abnormal:
Negative
pressureNormal:
1.4 ± 1.75
(14 ± 17.5)
(200 ± 249)

Abnormal:
0.69 ± 0.98
(7 ± 10)
(100 ± 142)
During A / C operation, the
low pressure side
sometimes indicates
negative pressure, and
sometimes normal
pressure. Also high
pressure side reading
fluctuates between the
abnormal and normal
pressure.
Expansion valve is frozen
due to moisture in the
system, and temporarily
shuts off the refrigeration
cycle.
Replace expansion
valve.

Replace receiver / dryer.

Evacuate A / C system
and recharge with fresh
refrigerant.
0.05 ± 0.15
(0.5 ± 1.5)
(4.2 ± 21.3)
0.69 ± 0.98
(7 ± 10)
(100 ± 142)

Both low and high pressure
sides indicate low readings.

Continuous air bubbles are
visible through sight glass.

Output air is slightly cold.
Insufficient refrigerant in
system. (Refrigerant
leaking)
Using a gas leak
detector, check for leaks
and repair as necessary.

Recharge refrigerant to a
specified amount.
If the pressure reading is
almost 0 when the
manifold gauges are
attached, check for any
leaks, repair them, and
evacuate the system.
0.4 ± 0.6
(4 ± 6)
(56.9 ± 85.3)

Pressure on low pressure
side is high.

Pressure on high pressure
side is low.

Both pressure becoming
equal right after A / C is
turned OFF.
Internal leak in compressor.
Inspect compressor and
repair or replace as
necessary.
035 045

High pressure reading on
both low and high pressure
sides.

Air bubbles are not visible
even when engine rpm is
lowered.
Overcharged A / C system.

Faulty condenser cooling
operation.

Faulty condenser fan
operation.
Adjust refrigerant to
specified amount.

Clean condenser.

Inspect and repair
condenser fan.
0.35 ± 0.45(3.5 ± 4.5)
(50 ± 64)
1.96 ± 2.45
(20 ± 25)
(285 ± 355)

High pressure reading on
both low and high pressure
sides.

Low pressure side tubing is
not cold when touched.

Air bubbles are visible
through sight glass.
Presence of air in A / C
system. (Improperly
evacuated)
Replace receiver / dryer.

Inspect quantity of
compressor oil and
presence of
contaminants in oil.

Evacuate system and
recharge with fresh
refrigerant.
0.45 ± 0.55
(4.5 ± 5.5)
(64 ± 78)

High pressure reading on
both low and high pressure
sides.

Large amount of frost or
dew on the low pressure
side tubing.
Faulty expansion valve.

Refrigerant flow is not
regulated properly.
Replace expansion
valve.

YH4
GRAND
VITARA
Charge 440
50 g, 14.2
1.9 oz of
refrigerant in gas form
AIR CONDITIONING (OPTIONAL) 1B-23
REFRIGERANT RECOVERY, EVACUATION AND CHARGING
WARNING:

Your eyes should not be exposed to refrigerant (liquid).
Any liquid Refrigerant-134a escaping by accident shows a temperature as low as approx. ± 6C
(42.8F) below freezing point. Should liquid HFC-134a (R-134a) get into your eyes, it may cause a seri-
ous injury. To protect your eyes against such accident, it is necessary to always wear goggles. Should
it occur that HFC-134a (R-134a) strikes your eye(s), consult a doctor immediately.
± DO NOT USE YOUR HAND TO RUB THE AFFECTED EYE(S). INSTEAD, use quantities of fresh cold
water to splash it over the affected area to gradually raise temperature of such area above freezing
point.
± Obtain proper treatment as soon as possible from a doctor or eye specialist.

Should the HFC-134a (R-134a) liquid come into contact with your skin, the affected area should be
treated in the same manner as when skin is frostbitten or frozen.

Refrigerant must not be handled near where welding or steam cleaning is performed.

Refrigerant should be kept at a cold and dark place. It should never be stored where a high tempera-
ture is anticipated, e.g. where exposed to direct sun light, close to fire or inside vehicle (including
trunk room).

Avoid breathing fumes produced when HFC-134a (R-134a) is burned. Such fumes may be hazardous
to health.
OPERATION PROCEDURE FOR CHARGING A / C WITH REFRIGERANT

YH4
GRAND
VITARA
1. ªHissº
AIR CONDITIONING (OPTIONAL) 1B-27
7) When refrigerant container (3) is emptied, use following proce-
dure to replace it with a new refrigerant container (3).
a. Close low pressure valve.
b. Replace empty container (3) with a refrigerant container
which has been charged with refrigerant. When using refrig-
erant container tap valve (4), use following procedure for re-
placement.
i) Retract needle (1) and remove refrigerant container tap
valve (4) by loosening its plate nut (2).
ii) Install previously-removed refrigerant container tap valve
(4) to a new refrigerant container (3).
c. Purge any air existing in center charging hose.
When using refrigerant container tap valve, use following
procedure to purge air.
i) Once fully tighten refrigerant container tap valve and then
loosen (open) plate nut slightly.
ii) Open low pressure valve of manifold gauge set a little.
iii) As soon as refrigerant comes out with a ªhissº through a
clearance between refrigerant container and tap valve,
tighten plate nut as well as manifold gauge set low pres-
sure valve.
iv) Turn handle of tap valve clockwise so that its needle is
screwed into the new container to make a hole for refriger-
ant flow.

YH4
GRAND
VITARA
1. Suction hose
2. Discharge hose
3. Liquid pipe
4. Condenser outlet pipe
5. Expansion valve
6. Dual pressure switch
7. Suction pipe
: Apply compressor oil
(refrigerant oil) to O-ring.
1B-30 AIR CONDITIONING (OPTIONAL)
ON-VEHICLE SERVICE
WARNING:
Should refrigerant HFC-134a (R-134a) strike your eye(s), consult a doctor immediately.

DO NOT USE YOUR HAND TO RUB AFFECTED EYE(S).
Instead, use quantities of fresh cold water to splash it over affected area to thus gradually raise its
temperature above the freezing point.

Obtain proper treatment as soon as possible from a doctor or eye specialist.
Should liquid refrigerant HFC-134a (R-134a) get on your skin, such affected part should be treated
in the same manner as when skin is frostbitten or frozen.
CAUTION:
None of refrigerant, compressor oil and component parts is interchangeable between two types of A / C:
one using CFC-12 (R-12) and the other using HFC-134a (R-134a).
(For identification between these two types, refer to page 1B-2).
When replenishing or changing refrigerant and compressor oil and when replacing parts, make sure
that the material or the part to be used is appropriate to the A / C installed in the vehicle being serviced.
Use of incorrect one will result in leakage of refrigerant, damage in parts or other faulty condition.
PRECAUTION
When servicing air conditioning system, the following rules must be observed.
PIPING

When connecting hoses and pipes, apply a few drops of compressor oil (refrigerant oil) to seats of coupling nuts
and O-ring.

Never use heat for bending pipes. When bending a pipe, try to make its bending radius as slight as possible.

Keep internal parts of air conditioning free from moisture and dirt. When disconnecting any line from system,
install a blind plug or cap to the fitting immediately.

When tightening or loosening a fitting, use two wrenches, one for turning and the other for support.

YH4
GRAND
VITARA
1
1. Mode control switch coupler
2. A / C switch
3. Indicator lamp
AIR CONDITIONING (OPTIONAL) 1B-45
A / C SWITCH
REMOVAL
1) Disconnect negative (±) cable at battery.
2) If equipped with air bag system, disable air bag system.
Refer to ªDISABLING AIR BAG SYSTEMº in Section 10B.
3) Remove mode control switch (Refer to ªMODE CONTROL
SWITCHº in Section 1A).
INSPECTION
A / C Switch

Press A / C button and check if there is continuity between termi-
nals ªDº and ªGº.

With battery voltage (+) connected to terminal ªKº and (±) to termi-
nal ªDº, press A / C button and check if indicator lamp lights.
INSTALLATION
1) Install in reverse order of removal procedure.
2) If equipped with air bag system, enable air bag system.
Refer to ªENABLING AIR BAG SYSTEMº in Section 10B.

YH4
GRAND
VITARA
(A)
1
1. Make alignment marks
1. Steering wheel
Turn slowly till coil stops
Turn contact coil back about 2 and
a half turns
1. Align marks
3C1-6 AIR BAG STEERING WHEEL AND COLUMN
STEERING WHEEL
CAUTION:
Removal of the steering wheel allows the contact coil to turn
freely but do not turn the contact coil (on the combination
switch) more than allowable number of turns (about two and
a half turns from the center position clockwise or counter-
clockwise respectively), or coil will break.
REMOVAL
1) Remove driver air bag (inflator) module from steering wheel re-
ferring to ªDRIVER AIR BAG (INFLATOR) MODULEº earlier in
this section.
2) Remove steering shaft nut.
3) Make alignment marks on steering wheel and shaft for a guide
during reinstallation.
4) Remove steering wheel with special tool.
Special Tool
(A): 09944-36011
CAUTION:
Do not hammer the end of the shaft. Hammering it will
loosen the plastic shear pins which maintain the column
length and impair the collapsible design of the column.
CENTERING CONTACT COIL
1) Check that vehicle's wheels (front tires) are set at straight-ahead
position.
2) Check that ignition switch is at ªLOCKº position.
3) Turn contact coil counterclockwise slowly with a light force till
contact coil will not turn any further.
NOTE:
Contact coil can turn about 5 turns at maximum, that is, if
it is at the center position, can turn about two and a half
turns both clockwise and counterclockwise.
4) From the position where contact coil became unable to turn any
further (it stopped), turn it back clockwise about two and a half
rotations and align center mark with alignment mark.

YH4
GRAND
VITARA
WHEELS AND TIRES 3F-7
TIRE
MOUNTING AND DEMOUNTING
Use tire changing machine to mount or demount tires. Follow equip-
ment manufacturer's instructions. Do not use hand tools or tire
irons alone to change tires as they may damage tire beads or wheel
rim.
Rim bead seats should be cleaned with wire brush or coarse steel
wool to remove lubricants, old rubber and light rust. Before mount-
ing or demounting tire, bead area should be well lubricated with ap-
proved tire lubricant.
After mounting, inflate to 240 kPa (35psi) so that beads are com-
pletely seated. Then adjust pressure to specified shown an tire
placard.
WARNING:
Do not stand over tire when inflating. Bead may break when
bead snaps over rim's safety hump and cause serious per-
sonal injury.
Do not exceed 240 kPa (35 psi) pressure when inflating. If
240 kPa (35 psi) pressure will not seat beads, deflate, re-lu-
bricate and reinflate. Over inflation may cause bead to break
and cause serious personal injury.
Install valve core and inflate to proper pressure.
TIRE REPAIR
There are many different materials and techniques on the market
to repair tires. As not all of these work on all types of tires, tire
manufacturers have published detailed instructions on how and
when to repair tires. These instructions can be obtained from the
tire manufacturer.

YH4
GRAND
VITARA
5
BRAKES 5-1
GENERAL DESCRIPTION5- 2 . . . . . . . . . . . . . .
DIAGNOSIS5- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Road Testing Brakes 5- 3. . . . . . . . . . . . . . . . . .
Brake Fluid Leaks 5- 3. . . . . . . . . . . . . . . . . . . .
Substandard or Contaminated
Brake Fluid 5- 3. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 5- 4. . . . . . . . . . . . . . . . . . . . . .
CHECK AND ADJUSTMENT5- 7 . . . . . . . . . . . .
Bleeding Brakes 5- 7. . . . . . . . . . . . . . . . . . . . . .
Brake Pedal Free Height Check 5- 9. . . . . . . .
Brake Light Switch Adjustment 5- 9. . . . . . . . .
Excessive Pedal Travel Check 5- 9. . . . . . . . .
Brake Pedal Play Check 5-10. . . . . . . . . . . . . . .
Brake Fluid Level Check 5-10. . . . . . . . . . . . . . . Brake Hose and Pipe Check 5-10. . . . . . . . . . .
Master Cylinder Check 5-10. . . . . . . . . . . . . . . .
Brake Disc Check 5-11. . . . . . . . . . . . . . . . . . . .
Brake Pad Check 5-11. . . . . . . . . . . . . . . . . . . . .
Brake Shoe Check 5-11. . . . . . . . . . . . . . . . . . . .
Parking Brake Check and
Adjustment 5-12. . . . . . . . . . . . . . . . . . . . . . . . .
Flushing Brake Hydraulic System 5-13. . . . . . .
Fluid Pressure Test 5-13. . . . . . . . . . . . . . . . . . .
Booster Operation Check 5-15. . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5-17 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIAL5-17 . . . . . . . .
SPECIAL TOOLS5-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 5
BRAKES
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:

When inspecting and servicing vehicle equipped with ABS, be sure to refer to section 5E or 5E1 first.

All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to as-
sure proper retention of all parts. There is to be no welding as it may result in extensive damage and
weakening of the metal.
DIAGNOSIS5-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BRAKE PIPE / HOSE / MASTER CYLINDER5A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT BRAKE5B-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARKING AND REAR BRAKE5C-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS

YH4
GRAND
VITARA
BRAKES 5-3
SUBSTANDARD OR
CONTAMINATED BRAKE FLUID
Improper brake fluid, mineral oil or water in the fluid
may cause the brake fluid to boil or the rubber compo-
nents in the hydraulic system to deteriorate.
If primary piston cups are swollen, then rubber parts
have deteriorated. This deterioration may also be evi-
denced by swollen wheel cylinder piston cups on the
drum brake wheels.
If deterioration of rubber is evident, disassemble all
hydraulic parts and wash with alcohol. Dry these parts
with compressed air before assembly to keep alcohol
out of the system. Replace all rubber parts in the sys-
tem, including hoses. Also, when working on the
brake mechanisms, check for fluid on the linings. If ex-
cessive fluid is found, replace the linings.
If master cylinder piston seals are satisfactory, check
for leakage or excessive heat conditions. If condition
is not found, drain fluid, flush with brake fluid, refill and
bleed system.
The system must be flushed if there is any doubt as
to the grade of fluid in the system or if fluid has been
used which contained parts that have been subjected
to contaminated fluid.
DIAGNOSIS
ROAD TESTING BRAKES
Brakes should be tested on dry, clean, smooth and
reasonably level roadway which is not crowned. Road
test brakes by making brake applications with both
light and heavy pedal forces at various speeds to de-
termine if the vehicle stops evenly and effectively.
Also drive vehicle to see if it leads to one side or the
other without brake application. If it does, check the
tire pressure, front end alignment and front suspen-
sion attachments for looseness. See diagnosis chart
for other causes.
BRAKE FLUID LEAKS
Check the master cylinder fluid levels. While a slight
drop in reservoir level does result from normal lining
wear, an abnormally low level indicates a leak in the
system. In such a case, check the entire brake system
for leakage. If even a slight evidence of leakage is
noted, the cause should be corrected or defective
parts should be replaced.
If fluid level is lower than the minimum level of reser-
voir, refilling is necessary. Fill reservoir with specified
brake fluid.
Brake fluid: Refer to reservoir tank cap.
CAUTION:
Since brake system of this vehicle is factory-
filled with brake fluid indicated on reservoir
tank cap, do not use or mix different type of
fluid when refilling; otherwise serious damage
will occur.
Do not use old or used brake fluid, or any fluid
from a unsealed container.

YH4
GRAND
VITARA
BRAKES 5-5
ConditionPossible CauseCorrection
Excessive pedal
travel (Pedal
stroke too large)
Partial brake system failure.

Insufficient fluid in master cylinder
reservoirs.

Air in system. (pedal soft / spongy)

Rear brake system not adjusted.
(malfunctioning auto adjusting mechanism)

Bent brake shoes.

Worn rear brake shoes.Check brake systems and repair as
necessary.
Fill reservoirs with approved brake
fluid.
Check for leaks and air in brake
systems.
Check warning light. Bleed system if
required.
Bleed system.
Repair auto adjusting mechanism.
Adjust rear brakes.
Replace brake shoes.
Replace brake shoes.
Dragging brakes
(A very light drag
is present in all
disc brakes
immediately
after pedal is
released)
Master cylinder pistons not returning
correctly.

Restricted brake pipes or hoses.

Incorrect parking brake adjustment on rear
brakes.

Weakened or broken return springs in the
brake.

Sluggish parking-brake cables or linkage.

Wheel cylinder or caliper piston sticking.

Malfunctioning ABS, if equipped with ABS.Replace master cylinder.
Check for soft hoses or damaged
pipes and replace with new hoses
and / or new brake pipes.
Check and adjust to correct specifi-
cations.
Replace.
Repair or replace.
Repair as necessary.
Check system and replace as
necessary.
Pedal pulsation
(Pedal pulsates
when depressed
for braking)
Damaged or loose wheel bearings.

Distorted steering knuckle or rear axle
shafts.

Excessive disc lateral runout.

Parallelism not within specifications.

Rear drums out of round.Replace wheel hub component.
Replace knuckle or rear axle shaft.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check runout.
Repair or replace drum as
necessary.
Braking noise
Glazed shoe linings, or foreign matters
stuck to linings.

Worn or distorted shoe linings.

Loose front wheel bearings.

Distorted backing plates or loose mounting
bolts.Repair or replace shoe lining.
Replace shoe lining (or pad).
Replace wheel hub component.
Replace or retighten securing bolts.