air SUZUKI GRAND VITARA 1999 2.G Service Workshop Manual

YH4
GRAND
VITARA
1. Seat cushion
2. Seat back
3. Seat auto lock release handle
4. Seat hinge male
5. Hinge male cover
BODY SERVICE 9-35
REAR SEAT
REMOVAL
1) Remove four mounting bolt to remove seat cushion.
2) Remove four mounting bolts to remove seat back.
3) Disassemble and repair seat as necessary.
INSTALLATION
Reverse removal procedure to install rear seat.
Torque to specifications, as shown.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)

YH4
GRAND
VITARA
9-36 BODY SERVICE
Sealer is applied to the specific joints of a vehicle dur-
ing production. The sealer is intended to prevent dust
from entering the vehicle and serves also as an anti-
corrosion barrier. The sealer is applied to the door and
hood hem areas and between panels. Correct and re-
seal the originally sealed joints if damaged. Reseal
the attaching joints of a new replacement panel and
reseal the hem area of a replacement door or hood.
Use a quality sealer to seal the flanged joints, overlap
joints and seams. The sealer must have flexible char-
acteristics and paintability after it's applied to repair
areas.
For the sealer to fill open joints, use caulking material.
Select a sealer in conformance with the place and
purpose of a specific use. Observe the manufactur-
er's label-stand instructions when using the sealer.
In many cases, repaired places require color painting.
When this is required, follow the ordinary techniques
specified for the finish preparation, color painting and
undercoating build-up.
Rust proof wax, a penetrative compound, is applied
to the metal-to-metal surfaces (door and side sill in-
sides) where it is difficult to use ordinary undercoating
material for coating. Therefore, when selecting the
rust proof wax, it may be the penetrative type.
During the undercoating (vinyl coating) application,
care should be taken that sealer is not applied to the
engine-related parts and shock absorber mounting or
rotating parts. Following the under coating, make
sure that body drain holes are kept open.
he sequence of the application steps of the anti-corro-
sion materials are as follows:
1) Clean and prepare the metal surface.
2) Apply primer.
3) Apply sealer (all joints sealed originally).
4) Apply color in areas where color is required such
as hem flanges, exposed joints and under body
components.
5) Apply anticorrosion compound (penetrative wax).
6) Apply undercoating (rust proof material).
PAINT AND COATINGS
ANTI-CORROSION TREATMENT
WARNING:
Standard shop practices, particularly eye
protection, should be followed during the per-
formance of the below-itemized operations to
avoid personal injury.
As rust proof treatment, steel sheets are given corro-
sion resistance on the interior and / or exterior.
These corrosion resistance steel sheet materials are
called one of two-side galvanized steel sheets.
It is for the sake of rust protection that these materials
are selected and given a variety of treatments as de-
scribed blow.
1) Steel sheets are treated with cathodic electroprim-
er which is excellent in corrosion resistance.
2) Rust proof wax coatings are applied to door and
side sill insides where moisture is liable to stay.
3) Vinyl coating is applied to body underside and
wheel housing inside.
4) Sealer is applied to door hem, engine compart-
ment steel sheet-to-steel sheet joint, and the like
portions to prevent water penetration and resulting
in rust occurrence.
In panel replacement or collision damage repair, leav-
ing the relevant area untreated as it is in any operation
which does disturb the above-mentioned rust proof
treatment will cause corrosion to that area. Therefore,
it is the essential function of any repair operation to
correctly recoat the related surfaces of the relevant
area.
All the metal panels are coated with metal condition-
ers and primer coating during vehicle production. Fol-
lowing the repair and / or replacement parts installa-
tion, every accessible bare metal surface should be
cleaned and coated with rust proof primer. Perform
this operation prior to the application of sealer and
rust proof wax coating.

YH4
GRAND
VITARA
When the welding or heating operation causes the
original galvanization or other anticorrosive materials
to be burnt, the interior and under-body panel sur-
faces must be cleaned.
Removal of residues of the burning should be carried
out carefully when the relevant place has boxtype
construction or has shape which limits the access to
the interior surfaces. In general, the following method
can be used satisfactorily for the removal of those res-
idues.Scrape the accessible places. If a standard putty knife
or scraper does not fit to the elevant place, consider
to use a more flexible scraper to a place narrowly en-
closed by sheet metals.
A jet of compressed air can remove most residues,
and is effective to limited areas.
However, this type of operation absolutely requires
eye protection.
BODY SERVICE 9-37
The metal service replacement parts (or assemblies)
are coated with electro-deposition primer.
For the proper adhesion of a paint, the following finish
process (refinish steps) becomes necessary.
1) Use wax or grease-removing solvent to clean the
part.
2) Use a wet or dry sand-paper (No. 400) to polish the
panel lightly. Do not polish it forcibly to produce any
scratch. Clean the part again.
3) If factory-applied primer coating is cut through to
the bare metal, apply metal conditioner to the bare
metal exposed to open air. As for method of use of
the metal conditioner, follow directions on the con-
tainer.
4) Apply primer-surfacer to the part completely dry
before starting sand-paper polishing. As for drying
time, follow directions advised on the primer-sur-
facer container.
5) Use a wet or dry sand-paper (No. 400) and water
to polish the panel lightly.
6) Wash the part again.
7) Apply color, coating to the part.
8) Different paints demand different drying methods.
Hence, follow directions advised on the pertinent
paint container.9) When lacquer coating (quick-drying paint coat-
ing) is applied, dry coated surface and polish it
with compound.
In the case of the melamine or acrylic coating,
compound polishing can be omitted after drying.
10) If the case of lacquer coating, wax should not be
applied to coated surface until the surface has
dried completely (for approx. two months).
Before replacing exterior parts or assemblies, check
paint conditions of all the covered or hidden interior
surfaces. If any rust scale is found at these places,
proceed as follows:
1) Use a proper wire brush, adhesive or liquid rust re-
moving agent to remove rust. As for the method of
use, follow directions advised for respecitve mate-
rials.
2) If necessary, wash parts with detergent, rinse, and
dry them.
3) Before installing exterior body parts, apply anticor-
rosive compound to all cleaner surfaces of exterior
body parts. Also, apply anticorrosive compound to
inner surfaces of exterior body parts to be
installed.
METAL REPLACEMENT PARTS FINISHING

YH4
GRAND
VITARA
9-58 BODY SERVICE
PLASTIC PARTS FINISHING
Paintable plastic parts are ABS plastic parts.
Painting
Rigid or hard ABS plastic needs no primer coating.
General acrylic lacquers can be painted properly over hard ABS
plastic in terms of adherence.
1) Use cleaning solvent for paint finish to wash each part.
2) Apply conventional acrylic color lacquer to part surface.
3) Follow lacquer directions for required drying time. (Proper dry-
ing temperature range is 60 to 70
C).
Reference
Plastic parts employ not only ABS (Acrylonitrile Butadiene Styrene)
plastic but also polypropylene, vinyl, or the like plastic. Burning test
method to identify ABS plastic is described below.
1) Use a sharp blade to cut off a plastic sliver from the part at its
hidden backside.
2) Hold sliver with pincers and set it on fire.
3) Carefully observe condition of the burning plastic.
4) ABS plastic must raise readily distinguishable back smoke while
burning with its residue suspended in air temporarily.
5) Polypropylene must raise no readily distinguishable smoke
while burning.

YH4
GRAND
VITARA
BODY SERVICE 9-63
KEY CODING
KEY USAGE AND IDENTIFICATION
Key is used for ignition and door lock cylinder. Keys are cut on both
edges to make them reversible.
Key identification is obtained from five character key code stamped
on key code tag. Using this key code, key code cutting combination
can be determined from a code list (available to owners of key cut-
ting equipment from suppliers).
If key codes are not available from records or tags, key code can
be obtained from the right hand door lock cylinder (if lock has not
been replaced). Lock cylinders supplied by the factory as service
parts are unmarked.
If original key is available, key code cutting combination can be de-
termined by laying key.
IGNITION SWITCH LOCK CYLINDER
Removal / Installation
See Section 3C1, ªAIR BAG STEERING WHEEL AND COLUMNº.
ELECTRICAL DIAGNOSIS
For ignition switch electrical troubleshooting, see Section 8, ªBODY
ELECTRICAL SYSTEMº.

YH4
GRAND
VITARA
9-80 BODY SERVICE
1. Bolt
2. Member
LUGGAGE UNDER BOX
WARNING:
Do not remove member in the center of luggage under box.
If member had to be removed temporarily for repair or for some oth-
er reason, be sure to reinstall it by using specified new bolts until
head of bolt is broken off.

YH4
GRAND
VITARA
10
RESTRAINT SYSTEM 10-1
SECTION 10
RESTRAINT SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
SEAT BELTSECTION 10A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR BAG SYSTEMSECTION 10B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION10-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSISRefer to ªDiagnosisº in SECTION 10A and 10B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
10-2 RESTRAINT SYSTEM
Driver Side Seat Belt: Seat belt with ELR
Front Passenger Side Seat And
Rear Left And Right Seat Belts: Seat belt with A-ELR
Rear Center Seat Belt (If Equipped): Seat belt without ELR and A-ELR
Supplemental Restraint System: Driver and front passenger side air bags
1. Driver side seat belt
2. Front passenger side seat belt
3. Rear left seat belt
4. Rear right seat belt
5. Rear center seat belt (If equipped)
6. Driver side air bag
7. Passenger side air bag
GENERAL DESCRIPTION
Seat belt with ELR
The seat belt with Emergency Locking Retractor (ELR) is designed so that it locks immediately (to prevent the web-
bing from being pulled out of the retractor any further) when any of the following items is detected as exceeding
each set value; speed at which the webbing is pulled out of the retractor, acceleration or deceleration of the vehicle
speed, and inclination.
Seat belt with A-ELR
The automatic and emergency locking retractor (A-ELR) works as an Emergency Locking Retractor (ELR) till its
webbing is pulled all the way out and then on as an Automatic Locking Retractor (ALR) till it is retracted fully.
ALR: Automatically locks when the webbing is pulled out from the retractor and allowed to retract even a little.
Then the webbing can not be pulled out any further, unless it is wound all the way back into the retractor, which
releases the lock and allows the webbing to be pulled out.
Driver and front passenger side air bags
The driver and front passenger side air bags are components of the air bag system. In occurrence of a front collision
with an impact larger than a certain set value, they are activated by the ignition signal from SDM to supplement
protection offered by the driver and front passenger seat belts.

the driver air bag (inflator) module is deployed from the center of the steering column

the passenger air bag (inflator) module from the top of the instrument panel in front of the front passenger seat
For more information, refer to SECTION 10B ªAir Bag Systemº.

YH4
GRAND
VITARA
10A
SEAT BELT 10A-1
SECTION 10A
SEAT BELT
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS
GENERAL DESCRIPTIONRefer to SECTION 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service precautions10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front seat belt10A-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear seat belt10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
10A-2 SEAT BELT
ON-VEHICLE SERVICE
SERVICE PRECAUTIONS
WARNING:
If replacing seat belt is necessary, replace buckle and ELR (or webbing) together as a set. This is for
the reason of ensuring locking of tongue plate with buckle. If these parts are replaced individually, such
a locking condition may become unreliable. For this reason, SUZUKI will supply only the spare buckle
and ELR (or webbing) in a set part.
Before servicing or replacing seat belts, refer to following precautionary items.

Seat belts should be normal relative to strap retractor and buckle portions.

Keep sharp edges and damaging objects away from belts. Avoid bending or damaging any portion of belt buckle,
latch plate and ELR.

Do not bleach or dye belt webbing. (Use only mild soap and lukewarm water to clean it.)

When installing a seat belt anchor bolt, start bolt by hand to prevent cross-threading.

Use only the correct seat belt anchor bolts and screws and tighten to the correct torque value.

Do not attempt any repairs on retractor mechanisms or retractor covers. Replace defective assemblies with new
replacement parts.

Keep belts dry and clean at all times.

If there exist any parts in question, replace such parts.

Replace belts whose webbing is cut or otherwise damaged.

Do not put anything into trim panel opening which seat belt webbing passes through.