Mount SUZUKI GRAND VITARA 1999 2.G Service Service Manual

YH4
GRAND
VITARA
3B1-20 POWER STEERING (P / S) SYSTEM
1. P/S fluid
reservoir
2. Suction hose
1. P / S pulley
2. Mounting bolt
9. Vane
10. Rotor
11. Snap ring
12. Side plate
13. Pulley (pump shaft)
14. Oil seal
15. Pump body
16. Flow control
valve Assembly 1. Suction connector
2. O-ring
3. Pressure switch
4. Flow control valve
(Relief valve)
5. Spring
6. Plug
7. Pump cover
8. Cam ring
REMOVAL
NOTE:
Be sure to clean each joint of suction and discharge sides
thoroughly before removal.
1) Remove suction hose from pump, then disconnect battery nega-
tive cable.
2) Remove P / S fluid reservoir with suction hose.
3) Remove union bolt. Then disconnect high pressure pipe from
pump.
NOTE:
As fluid flows out of disconnected joints, put a receptacle
under joints or a plug to pipe.
4) Disconnect pressure switch lead wire at switch terminal.
5) Loosen related bolts and remove power steering drive belt.
6) Remove P / S pump mounting bolt (s).
7) Remove P / S pump.
NOTE:
Plug each port of removed pump to prevent dust or any oth-
er foreign matter from entering.
DISASSEMBLY
1) Clean its exterior thoroughly.
2) With aluminum plates placed on vise first, grip pump body with
it.
3) Remove suction connector bolt, suction connector and O-ring
from pump body.
4) Remove power steering pressure switch (terminal set) from
pump body.
5) Remove plug, flow control spring and relief valve (flow control
valve) from pump body.
6) Remove cover bolts, pump cover and O-ring from pump body.
7) Remove snap ring from pump shaft.
8) Remove vanes from rotor.
9) Remove cam ring, rotor, side plate and O-rings from pump
body.
10) Pull out pulley from pump body.
11) Remove oil seal from pump body.

YH4
GRAND
VITARA
3B1-26 POWER STEERING (P / S) SYSTEM
09915-77420
Oil pressure gauge
attachment and hose set09915-77410
Oil pressure gauge09943-55010
Boot clamp plier
TIGHTENING TORQUE SPECIFICATION
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Gear box mounting bolts555.540.0
Gear box cylinder pipe flare nuts292.921.0
Gear box low pressure pipe union bolt404.029.0
Gear box high pressure pipe union bolt353.525.5
Tie-rod end lock nut656.547.0
G16 Type engine555.540.0
Pump bracket boltJ20 Type engine252.518.5
H25 Type engine454.532.5
Pump union bolt606.043.5
Oil pump mount bolts252.518.5
Pipe clamp bolt / Reservoir bracket bolt111.18.0
Steering shaft joint bolt252.518.0
High pressure flare nuts404.029.0
Pump cover bolts232.317.0
Plug606.043.5
Pressure switch (Terminal)282.820
Suction connector bolt101.07.5
Tie-rod end nut484.835.0
Tie-rod (for canvas top LH model only)858.561.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUPER GREASE (A)
(99000-25010)
Oil seal lip of P / S pump pulley shaft
Power steering fluidAn equivalent of DEXRON
-III or
DEXRON
-II

To fill P / S fluid reservoir

Parts lubrication when installing
SPECIAL TOOL

YH4
GRAND
VITARA
3C
STEERING WHEEL AND COLUMN 3C-1
SECTION 3C
STEERING WHEEL AND COLUMN
(NOT EQUIPPED WITH AIR BAG)
NOTE:
All steering wheel and column fasteners are important parts in that they could affect the performance of
vital parts and systems, and / or could result in major repair expense. They must be replaced with one of
the same part number or with an equivalent part if replacement becomes necessary. Do not use a replace-
ment part of lesser quality of substitute design. Torque values must be used as specified during reassemb-
ly to assure proper retention of this part.
CONTENTS
GENERAL DESCRIPTION3C- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS3C- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and repair required after accident 3C- 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering wheel3C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Combination switch3C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering column assembly3C- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering lock assembly (ignition switch) 3C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering lower shaft assembly3C-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking steering column for accident damage 3C-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable steering column release lever 3C-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS3C-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL3C-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
This double tube type steering column has the following three important features in addition to the steering function:

The column is energy absorbing, designed to compress in a front-end collision.

The ignition switch and lock are mounted conveniently on this column.

With the column mounted lock, the ignition and steering operations can be locked to inhibit theft of the vehicle.
To insure the energy absorbing action, it is important that only the specified bolts be used as designated and that
they are tightened to the specified torque. When the column assembly is removed from the vehicle, special care
must be taken in handling it. Use of a steering wheel puller other than the one recommended in this manual or a
sharp blow on the end of the steering shaft, leaning on the assembly, or dropping the assembly could shear the
plastic shear pins which maintain column length and position.

YH4
GRAND
VITARA
1. Steering column hole cover
2. If equipped
1. Steering column cover screw
2. Steering column lower cover
3. Steering column upper cover: Tapping screw
: Standard screw
*
* *
STEERING WHEEL AND COLUMN 3C-5
3) Install steering column upper and lower cover.
4) Tighten steering column cover screws.
CAUTION:
When installing lower cover and upper cover, be careful
so that combination switch lead wire is not caught be-
tween covers.
5) Install steering column hole cover.
6) Install steering wheel to steering column. Refer to ªSTEERING
WHEELº in this section.
7) Connect battery negative cable.
STEERING COLUMN ASSEMBLY
CAUTION:
Once the steering column is removed from the vehicle, the
column is extremely susceptible to damage.
Dropping the column assembly on its end could collapse
the steering shaft or loosen the plastic shear pins which
maintain column length. Leaning on the column assembly
could cause it to bend or deform.
Any of the above damage could impair the column's col-
lapsible design.
When loosening steering column mounting bolts, make
sure that steering column assembly and steering shaft low-
er assembly have been separated. Loosening them with
steering column assembly and steering shaft lower assem-
bly assembled could cause damage to bearing in steering
shaft lower assembly.
NOTE:
When servicing steering column or any column-mounted
component, remove steering wheel. But when removing steer-
ing column simply to gain access to instrument panel compo-
nents, leave steering wheel installed on steering column.
REMOVAL
1) Disconnect negative battery cable at battery terminal.

YH4
GRAND
VITARA
1. Steering column
2. Steering column mounting bolt
3. Steering column lower seal
1. Shift (key) interlock cable
2. Screw
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly ªaº
STEERING WHEEL AND COLUMN 3C-7
7) Remove steering column mounting bolts (6 pieces).
8) If equipped with shift (key) interlock cable, remove shift (key) in-
terlock cable screw and then disconnect its cable from ignition
switch.
9) Remove steering column from vehicle.
INSPECTION
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted or air bag
deployed, may have a damaged or misaligned steering col-
umn.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)

YH4
GRAND
VITARA
1. Steering column
2. Mounting bolt
3. Steering column lower seal
4. Dash panel
1. Steering column lower seal
In engine room
In cabin
3C-8 STEERING WHEEL AND COLUMN
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering lower shaft assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.
INSTALLATION
CAUTION:

After tightening steering column mounting bolts, steering
shaft joint bolts should be tightened.

After tightening steering column lower bolts, steering col-
umn upper bolts should be tightened.
1) Be sure that front wheels and steering wheel are in straight-
ahead position.
2) If equipped with shift (key) interlock cable, install shift (key) inter-
lock cable to ignition switch.
3) Install steering column assembly to dash panel and upper
bracket so that boss of steering column lower seal and all around
it project out of hole in dash panel into engine room. Tighten
steering column lower bolts (4 pieces) first and then upper bolts
(2 pieces) to specified torque.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
1. Steering column
2. Steering lock
1. Center punch (with sharp point)
2. Steering lock mounting bolt
1. Steering column
2. Steering shaft
3C-10 STEERING WHEEL AND COLUMN
STEERING LOCK ASSEMBLY (IGNITION
SWITCH)
REMOVAL
1) Remove steering column. Refer to ªSTEERING COLUMNº in
this section.
2) Using center punch as shown, loosen and remove steering lock
mounting bolts.
NOTE:
Use care not to damage aluminum part of steering lock
body with center punch.
3) Turn ignition key to ªACCº or ªONº position and remove steering
lock assembly from steering column.
INSTALLATION
1) Position oblong hole of steering shaft in the center of hole in col-
umn.
2) Turn ignition key to ªACCº or ªONº position and install steering
lock assembly onto column.
3) Now turn ignition key to ªLOCKº position and pull it out.
4) Align hub on lock with oblong hole of steering shaft and rotate
shaft to assure that steering shaft is locked.
5) Tighten new bolts until head of each bolt is broken off.
6) Turn ignition key to ªACCº or ªONº position and check to be sure
that steering shaft rotates smoothly. Also check for lock opera-
tion.
7) Install steering column. Refer to ªSTEERING COLUMNº in this
section.

YH4
GRAND
VITARA
1. Lower position
2. Upper position
3C-14 STEERING WHEEL AND COLUMN
09944-36011
Steering wheel remover
ADJUSTABLE STEERING COLUMN RELEASE
LEVER
INSPECTION
Check to make sure that the following:

Steering column moves smoothly when adjustable steering col-
umn release lever is at lower position (i.e., steering column is not
locked).

Steering column is fixed securely when adjustable steering col-
umn release lever is at higher position (i.e., steering column is
locked).
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Steering shaft nut333.323.5
Steering column mounting bolt232.317.0
Steering shaft joint bolt252.518.0
Steering lower shaft assembly lower joint bolt252.518.0
SPECIAL TOOL

YH4
GRAND
VITARA
14
15
1. Driver air bag (inflator) module
2. Steering wheel
3. Steering wheel nut
4. Contact coil and combination switch assembly
5. Steering column upper cover
6. Steering column lower cover
7. Steering column assembly
8. Steering lock assembly
9. Steering column hole cover
10. Steering shaft joint
11. Steering lower shaft assembly
12. Adjustable steering column release lever
(if equipped)
13. Steering column lower seal
14. With adjustable steering column release lever type
15. Without adjustable steering column release lever type
3C1-2 AIR BAG STEERING WHEEL AND COLUMN
GENERAL DESCRIPTION
This double tube type steering column has the following three important features in addition to the steering function:

The column is energy absorbing, designed to compress in a front-end collision.

The ignition switch and lock are mounted conveniently on this column.

With the column mounted lock, the ignition and steering operations can be locked to inhibit theft of the vehicle.
To insure the energy absorbing action, it is important that only the specified screws, bolts, and nuts be used as
designated and that they are tightened to the specified torque. When the column assembly is removed from the
vehicle, special care must be taken in handling it. Use of a steering wheel puller other than the one recommended
in this manual or a sharp blow on the end of the steering shaft, leaning on the assembly, or dropping the assembly
could shear the plastic shear pins which maintain column length and position.
The driver air bag (inflator) module is one of the supplemental restraint (air bag) system components and is
mounted to the center of the steering wheel. During certain frontal crashes, the air bag system supplements the
restraint of the driver's and passenger's seat belts by deploying the air bags. The air bag (inflator) module should
be handled with care to prevent accidental deployment. When servicing, be sure to observe all WARNINGS in this
section. Refer to ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
1 11
1. Mounting bolt
1. Driver air bag (inflator) module connector
2. Horn connector
3. Driver air bag (inflator) module
4. Steering wheel
3C1-4 AIR BAG STEERING WHEEL AND COLUMN
DRIVE AIR BAG (INFLATOR) MODULE
WARNING:
When handling an air bag (inflator) module, be sure to read
ªSERVICE PRECAUTIONSº under ªON-VEHICLE SERVICEº
in Section 10B and observe each instruction. Failure to fol-
low them could cause a damage to the air bag (inflator) mod-
ule or result in personal injury.
REMOVAL
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Loosen 2 bolts mounting driver air bag (inflator) module till it
turns freely, pull them out and fix them to bolt clamps.
4) Remove air bag (inflator) module from steering wheel.
5) Remove driver air bag (inflator) module (yellow) connector and
horn connector from steering wheel.
6) Disconnect driver air bag (inflator) module (yellow) connector of
driver air bag (inflator) module and horn connector as shown in
the figure.
ii) Release locking of lever.
ii) After unlocked, disconnect connector.
WARNING:
Special care is necessary when handling and storing a
live (undeployed) air bag (inflator) module. Observe
ªSERVICE PRECAUTIONSº under ªON-VEHICLE SER-
VICEº in Section 10B. Otherwise, personal injury may re-
sult.