Od off SUZUKI GRAND VITARA 2000 2.G Service Workshop Manual

YH4
GRAND
VITARA
8D-26 WINDOWS, MIRRORS, SECURITY AND LOCKS
IGNITION SWITCH AND DOOR SWITCH CIRCUIT
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect coupler of power door lock and keyless entry con-
troller, and connect negative cable at battery.
3) Check that the voltage and resistance between following termi-
nals are specifications.
Terminals
ConditionSpecification
E02-4 and
When ignition switch is OFF
position0 V
groundWhen ignition switch is ON
position10 ± 14 V
E02 10 andWhen all doors are closedNo continuityE02-10 and
groundWhen any one door is
openedContinuity
If check result is satisfactory, this circuit is OK.
DOOR KNOB SWITCH AND TURN SIGNAL RELAY CIRCUIT
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect coupler of power door lock and keyless entry con-
troller, and connect negative cable at battery.
3) Check that the voltage and resistance between following termi-
nals are specifications.
Terminals
ConditionSpecification
E02-6 and
groundAnytime10 ± 14 V
E02-11 and
When driver side door lock
knob is pulled upContinuity
groundWhen driver side door lock
knob is pushed downNo continuity
If check result is satisfactory, this circuit is OK.

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-29
CODE REGISTRATION PROCEDURE
1) Confirm that IG switch is OFF position and all doors are closed.
2) Open driver side door and then turn the IG switch to ON position
within 10 seconds.
3) Turn the IG switch to OFF position within 10 seconds after it is
turned to ON position.
4) Push and release the door switch to turn OFF and ON at three
times by hand within 20 seconds after the IG switch is turned to
OFF position.
5) Within 10 seconds after the door switch is turned to ON, turn the
IG switch to ON position and then OFF position.
6) Push and hold the LOCK and UNLOCK buttons on transmitter
at the same time within 20 seconds after IG switch is turned to
OFF position. Hold the buttons for at least 5 seconds. During this
time, the driver side door should lock and unlock once.
7) Push LOCK or UNLOCK buttons on transmitter within 5 seconds
after Step 6), and then confirm that driver side door is locked and
unlocked once.
NOTE:

Two transmitter codes can be registered.

When a new transmitter is registered, the oldest one will
be cleared.

YH4
GRAND
VITARA
8D-32 WINDOWS, MIRRORS, SECURITY AND LOCKS
3. To open
4. To close
3. Left turn
4. Right turn
Terminal
Switch
Terminal
Switch
POWER SLIDING ROOF (IF EQUIPPED)
INSPECTION
SLIDING ROOF SWITCH
Check switch for continuity between terminals as shown below.
Slide Switch (1)
CDFCDF
OPEN
OFF
CLOSE
Tilt Switch (2)
EDBEDB
UP
OFF
DOWN
SLIDING ROOF MOTOR ASSEMBLY
1) Remove head lining. Refer to Section 9 for detail.
2) Remove sliding roof motor assembly (1).
3) Connect known-good sliding roof switch (2) to sliding roof motor
assembly.
4) Connect 12 V battery positive terminal to terminal ªAº of motor
assembly (1) and battery negative terminal to terminal ªBº of mo-
tor assembly (1).
5) Check that the sliding roof motor (1) runs according to the move-
ment of the sliding roof switch (2).
Sliding Roof Switch
Motor
Tilt upturns left
Tilt downturns right
Slide openturns right
Slide closeturns left
If motor does not operate as above, replace sliding roof motor
assembly (1).

YH4
GRAND
VITARA
Hard Top Model
Canvas Top Model
LOAD2 LOAD1
1. Heater wire
2. Thermostat
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-33
FRONT SEAT HEATER (IF EQUIPPED)
SEAT HEATER SWITCH (DRIVER AND PASSENGER SIDE)
INSPECTION
1) Confirm that ignition switch is OFF position.
2) Pull out seat heater switch from front center console box.
3) Disconnect seat heater switch coupler.
4) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace.
SEAT HEATER WIRE
INSPECTION
1) Confirm that seat heater switch is OFF position.
2) Disconnect two couplers of seat heater under the seat cushion.
(If seat under tray is equipped, pull out coupler between tray and
seat cushion.)
3) Check for continuity between terminals as shown below.
If not continuity, replace faulty seat heater.
Hard Top Model
Seat heater circuit in seat back
Between a and b
Between b and d
Between c and e
Seat heater circuit in seat cushion
Between f and g
Canvas Top Model
Seat heater circuit in seat back
Between A And B
Seat heater circuit in seat cushion
Between C and D
Between D and F
Between E and G

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-7
[INTERMITTENT TROUBLES]


There are cases where output of diagnostic output terminal
and / or malfunction indicator lamp indicate a diagnostic trouble
code representing a trouble which occurred only temporarily and
has gone. In such case, it may occur that good parts are replaced
unnecessarily. To prevent such accident, be sure to follow instruc-
tions given below when checking by using ªDiagnostic Flow
Tableº.
* When trouble can be identified, it is not an intermittent one:
Check coil antenna, ignition key, wires and each connection
and if they are all in good condition, substitute a known-good
ECM / PCM and recheck.
* When trouble can not be identified but output of diagnostic out-
put terminal and / or malfunction indicator lamp indicate a
trouble code:
Diagnose trouble by using that code No. and if ignition key, coil
antenna, wires and each connection are all in good condition,
turn OFF ignition switch and then ON.
Then check what malfunction indicator lamp and / or output of diag-
nostic output terminal indicate.
Only when they indicate trouble code again, substitute a known-
good ECM / PCM or Immobilizer Control Module and check again.
If they indicate not trouble code but normal code, it means that an
intermittent trouble did occur and has gone. In this case, check
wires and connections carefully again.


There are cases where output of diagnostic output terminal and/
or Suzuki scan tool indicates a diagnostic trouble code represent-
ing a trouble which occurred only temporarily and has gone. In
such case, it may occur that good parts are replaced unnecessar-
ily. To prevent such accident, be sure to follow instructions given
below when checking by using ªDiagnostic Flow Tableº.
* When trouble can be identified, it is not an intermittent one:
Check coil antenna, ignition key, wires and each connection
and if they are all in good condition, substitute a known-good
ECM / PCM and recheck.
* When trouble can not be identified but output of diagnostic out-
put terminal and/or Suzuki scan tool indicates a trouble code:
Diagnose trouble by using that code No. and if ignition key, coil
antenna, wires and each connection are all in good condition,
turn OFF ignition switch and then ON.
Then check what Suzuki scan tool and/or output of diagnostic out-
put terminal indicates.
Only when they indicate trouble code again, substitute a known-
good ECM / PCM or Immobilizer Control Module and check again.
If they indicate not trouble code but normal code, it means that an
intermittent trouble did occur and has gone. In this case, check
wires and connections carefully again.

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-9
Fig. 1 for Step 1 Fig. 2 for Step 1 Fig. 3 for Step 2
1. Monitor coupler
2. Service wire
A: Diagnosis switch terminal
B: Ground terminal
Fig. 4 for Step 3
ªCHECK ENGINEº light
0.5
ON
OFF
TIME (sec.)
DIAGNOSTIC FLOW TABLE

STEPACTIONYESNO
11) Make sure that diagnosis switch
terminal in monitor coupler is not
grounded by service wire. See Fig. 1.
2) Check malfunction indicator lamp
while ignition switch is ON (but without
starting engine). See Fig. 2.
Dose malfunction indicator lamp flash?Go to Step 3.
If malfunction indicator lamp
remains ON, go to Step 2.

If malfunction indicator lamp
remains OFF, go to
ªMALFUNCTION INDICATOR
LAMP CHECKº in Section 6.
21) Using service wire, ground diagnosis
switch terminal in monitor coupler.
See Fig. 3.
Dose malfunction indicator lamp flash?Immobilizer control
system is in good
condition.Go to ªMALFUNCTION
INDICATOR LAMP CHECKº in
Section 6.
3Dose malfunction indicator lamp flash as
Fig. 4?Go to Step 4.Go to ªMALFUNCTION
INDICATOR LAMP CHECKº in
Section 6.
41) Check DTC stored in immobilizer
control module referring to
ªDIAGNOSTIC TROUBLE CODE
CHECK (IMMOBILIZER CONTROL
MODULE)º in this section.
Is there any DTC(s)?Go to flow table for
DTC No.Go to Step 5.
51) Check DTC stored in ECM/PCM
referring to ªDIAGNOSTIC TROUBLE
CODE CHECK (ECM / PCM)º in this
section.
Is there any DTC(s)?Go to flow table for
DTC No.Substitute a known-good ECM/
PCM and recheck.
NOTE:
After replacing with a known-
good ECM/PCM, register
ECM / Immobilizer Control
Module code in ECM/PCM by
performing procedure described
in ªProcedure after ECM/PCM
Replacementº section.

YH4
GRAND
VITARA
8G-10 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
DIAGNOSTIC FLOW TABLE

STEPACTIONYESNO
11) Check immobilizer indicator lamp
while ignition switch is ON (but without
starting engine). See Fig. 1.
Dose immobilizer indicator lamp flash?Go to Step 3.
If immobilizer indicator lamp
remains ON, go to Step 2.

If immobilizer indicator lamp
remains OFF, go to
ªIMMOBILIZER INDICATOR
LAMP CHECKº in this section.
21) Check DTC stored in ECM / PCM
referring to ªDIAGNOSTIC TROUBLE
CODE CHECK (ECM / PCM)º in this
section.
Is there any DTC(s)?Go to ªIMMOBILIZER
INDICATOR LAMP
CHECKº in this section.Immobilizer control system is in
good condition.
31) Check DTC stored in immobilizer
control module referring to
ªDIAGNOSTIC TROUBLE CODE
CHECK (IMMOBILIZER CONTROL
MODULE)º in this section.
Is there any DTC(s)?Go to flow table for
DTC No.Go to Step 4.
41) Check DTC stored in ECM / PCM
referring to ªDIAGNOSTIC TROUBLE
CODE CHECK (ECM / PCM)º in this
section.
Is there any DTC(s) for immobilizer
control system?Go to flow table for
DTC No.Substitute a known-good ECM /
PCM and recheck.
NOTE:
After replacing with a known-
good ECM / PCM, register
ECM / Immobilizer Control
Module code in ECM / PCM by
performing procedure described
in ªProcedure after ECM / PCM
Replacementº section.
FIg. 1 for Step 1

YH4
GRAND
VITARA
8G-12 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
EXAMPLE: When serial data link wire is defective (Code No.83)
ON
OFFMalfunction
indicator lamp
Code No.83 Code No.83 Code No.83
Time (sec.)
1. Data link connector (DLC)
3) After completing the check, turn ignition switch OFF and discon-
nect service wire from monitor coupler.
[Using SUZUKI scan tool]
1) Turn ignition switch OFF.
2) After setting cartridge to Suzuki scan tool, connect it to data link
connector (DLC) located on underside of instrument panel at
driver's seat side.
Special Tool
(A): 09931-76011 (Suzuki scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 12 pin DLC adapter)
3) Turn ignition switch ON.
4) Read DTC according to instructions displayed on Suzuki scan
tool and print it or write it down. Refer to Suzuki scan tool opera-
tor's manual for further details.
NOTE:

When reading DTC stored in ECM / PCM using Suzuki scan
tool, select ªECMº from the applications menu and ªSU-
ZUKI modeº from the communication mode menu dis-
played on Suzuki scan tool.

If ECM / PCM detects a trouble in both electric fuel injec-
tion system and immobilizer control system, Suzuki scan
tool indicates trouble codes of both systems using Suzu-
ki mode of ECM application.
If communication between Suzuki scan tool and ECM / PCM is
not possible, check if Suzuki scan tool is communicable by con-
necting it to ECM / PCM in another vehicle. If communication is
possible in this case, Suzuki scan tool is in good condition. Then
check data link connector and serial data line (circuit) in the ve-
hicle with which communication was not possible.
5) After completing the check, turn ignition switch OFF and discon-
nect Suzuki scan tool from data link connector (DLC).

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-15
1. Main fuse
2. Main relay
3. ECM/PCM
4. Immobilizer indicator lamp
(Vehicle not equipped with
monitor coupler) For G16 / J20 engine For H25 engine
G16 / J20 Engine
H25 Engine
TABLE B IMMOBILIZER INDICATOR LAMP CHECK
(IMMOBILIZER INDICATOR LAMP DOSE NOT LIGHT AT IGNITION
SWITCH ON)
STEPACTIONYESNO
11) Turn ignition switch ON.
Do other indicator / warning lights in
combination meter come ON?Go to Step 2.ªIGº fuse blown, main fuse blown,
ignition switch malfunction,
ªB / Wº circuit between ªIGº fuse
and combination meter or poor
coupler connection at
combination meter.
21) Turn ignition switch OFF and
disconnect connectors from ECM /
PCM.
2) Check for proper connection to ECM /
PCM at terminal E61-5 for G16 / J20
engine or E61-23 for H25 engine.
3) If OK, then using service wire, ground
terminal E61-5 for G16 / J20 engine or
E61-23 for H25 engine in connector
disconnected.
Does immobilizer indicator lamp turn on
at ignition switch ON?Substitute a known-
good ECM / PCM and
recheck.Bulb burned out or ª(b)º wire
circuit open.

YH4
GRAND
VITARA
8G-16 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
1. Main fuse
2. Main relay
3. ECM / PCM
4. Immobilizer indicator lamp
(Vehicle not equipped with
monitor coupler) For G16 / J20 engine For H25 engine
G16 / J20 Engine
H25 Engine
TABLE C IMMOBILIZER INDICATOR LAMP CHECK
(IMMOBILIZER INDICATOR LAMP REMAINS ON AFTER ENGINE
STARTS)
STEPACTIONYESNO
11) With ignition switch OFF, disconnect
couplers from ECM / PCM.
Does immobilizer indicator lamp turn ON
at ignition switch ON?ª(p)º wire shorted to
ground circuit.Substitute a known-good ECM /
PCM and recheck.