Oil SUZUKI GRAND VITARA 2000 2.G Service Workshop Manual

YH4
GRAND
VITARA
8C
INSTRUMENTATION / DRIVER INFORMATION 8C-1
GENERAL DESCRIPTION8C- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8C- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8C- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8C- 2. . . . . . . . . . . . . . . . .
Abbreviations 8C- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8C- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8C- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8C- 2. . . . . . . . . . . . . . . .
Combination Meter 8C- 2. . . . . . . . . . . . . . . . . . .
DIAGNOSIS8C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 4. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 4. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C- 4. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light Remainder Warning Buzzer 8C- 5. . . . . . . Seat Belt Warning Light (If Equipped) 8C- 5. . .
Ignition Key Remainder Warning
Buzzer (If Equipped) 8C- 5. . . . . . . . . . . . . . . . .
Cigarette Lighter and Accessory Socket 8C- 5.
ON-VEHICLE SERVICE8C- 6 . . . . . . . . . . . . . . . .
Ignition (Main) Switch 8C- 6. . . . . . . . . . . . . . . . .
Combination Meter 8C- 7. . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 8. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 9. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C-11. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Key Remainder (If Equipped) /
Light Remainder Warning Buzzer 8C-12. . . . . .
Door Switch 8C-13. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Warning Light (If Equipped) 8C-13. . .
SECTION 8C
INSTRUMENTATION/DRIVER INFORMATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
1. Tachometer
2. Speedometer
3. Fuel level meter
4. Water temperature meter
5. Turn signal pilot light (LH)
6. 4WD indicator (if equipped)
7. ABS warning light (if equipped)
8. Immobilizer warning light (if equipped)
9. CHECK ENGINE light
10. Turn signal pilot light (RH)11. AIR BAG warning light (if equipped)
12. O / D OFF light (A / T vehicle only)
13. Fasten seat belt light (if equipped)
14. High beam light
15. Oil pressure warning light
16. Charge warning light
17. Brake and parking brake warning light
18. POWER indicator light (A / T vehicle only)
19. Shift position indicator (A / T vehicle, if equipped)or
CHECK
ENGINEor
ABS
8C-2 INSTRUMENTATION / DRIVER INFORMATION
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
COMBINATION METER

YH4
GRAND
VITARA
1. To door switch (driver side) B / Bl
2. To transmission range switch G / Bl
(A / T vehicle only, if equipped) L
3. To transmission range switch G / O
(A / T vehicle only, if equipped) 2
4. To transmission range switch Y / G
(A / T vehicle only, if equipped) D
5. To transmission range switch O / Bl
(A / T vehicle only, if equipped) N
6. To transmission range switch O / G
(A / T vehicle only, if equipped) P
7. To transmission range switch R
(A / T vehicle only, if equipped) R
8. To ground B
9. To PCM (A / T vehicle only) W / B
10. To ECT sensor Y / W
11. To fuel level gauge Bl / W
12. To ground B / Y
13. To combination switch G / Y
NOTE:
Terminal arrangement of coupler viewed from harness side.
Coupler A Coupler B Coupler C
Coupler A Coupler B Coupler C
1. Blank ÐÐ
2. Blank ÐÐ
3. To ignition switch B / W
4. Blank ÐÐ
5. To ABS control module Bl / O
(if equipped)
6. To PCM (A / T vehicle only) Gr / Bl
7. To ABS control module Br
(if equipped)
8. To VSS Bl / Y
9. To combination switch G / R
10. To SDM (if equipped) Y / G or Bl
11. To main fuse W / Bl
12. To fuse box W
13. To combination switch R
14. To ECM (PCM for A / T vehicle) V
(if equipped)
15. To ECM (PCM for A / T vehicle) V / Y
16. To ECM (PCM for A / T vehicle) O / B
(if equipped)1. To ground B
2. To ECM (PCM for A / T vehicle) Br
3. To ignition switch (if equipped) V / R
4. To brake fluid level switch R / B
5. To parking brake switch V
6. To seat belt switch (if equipped) Gr / R
7. To generator W / R
8. To oil pressure switch Y / B
9. To combination switch R / Y
10. To ignition switch (if equipped) Bl / R or CHECK
or ENGINE
or ABSif equipped
if equippedif equipped
INSTRUMENTATION / DRIVER INFORMATION 8C-3

YH4
GRAND
VITARA
8C-4 INSTRUMENTATION / DRIVER INFORMATION
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
SPEEDOMETER AND VSS
TroublePossible CauseCorrection
Speedometer shows no
operation
ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

VSS faulty

Printed plate in combination meter
faulty

Speedometer faulty

Wiring or grounding faultyReplace fuse to check for short
Replace VSS
Replace printed plate
Replace speedometer
Repair
FUEL METER / FUEL GAUGE UNIT
TroublePossible CauseCorrection
Fuel meter shows no
operation
ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

Fuel gauge unit faulty

Printed plate in combination meter
faulty

Fuel meter faulty

Wiring or grounding faultyReplace fuse to check for short
Replace fuel gauge unit
Replace printed plate
Replace fuel meter
Repair
ENGINE COOLANT TEMP. (ECT) METER AND SENSOR
TroublePossible CauseCorrection
Engine coolant temp.
meter shows no operation
ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

ECT meter faulty

Printed plate in combination meter
faulty

ECT sensor faulty

Wiring or grounding faultyReplace fuse to check for short
Replace ECT meter
Replace printed plate
Replace ECT sensor
Repair
OIL PRESSURE LIGHT
TroublePossible CauseCorrection
Oil pressure warning light
does not light up
Bulb in combination meter blown

ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)

Printed plate in combination meter
faulty

Oil pressure switch faulty

Wiring or grounding faultyReplace bulb
Replace fuse to check for short
Replace printed plate
Replace oil pressure switch
Repair

YH4
GRAND
VITARA
G16
J20
H25
1. Oil pressure switch
INSTRUMENTATION / DRIVER INFORMATION 8C-11
INSPECTION
1) Warm up ECT sensor (1) observing resistance between sensor
terminal (2) and sensor unit (1). Resistance should be de-
creased with increase of its temperature.
2) Check resistance between sensor terminal (2) and sensor unit
(1) shown below. If check result is not as specified, replace sen-
sor.
Temperature
Resistance
50
C (122
F)136 ± 216

OIL PRESSURE LIGHT
OIL PRESSURE SWITCH
REMOVAL AND INSTALLATION
Refer to OIL PRESSURE CHECK in Section 6A1 (for G16), Section
6A2 (for H25), and Section 6A4 (for J20) of this manual for details.
INSPECTION
1) Disconnect oil pressure switch (1) lead wire.
2) Check for continuity between oil pressure switch terminal (2)
and cylinder block (3) as shown.
During Engine Running
No continuity
At Engine StopContinuity
If check result is not as specified, replace oil pressure switch (1).

YH4
GRAND
VITARA
WASHER
ONINT
LO
HI
Type A
Type B
Type C
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-9
Wiper
SW
Terminal
Wiper SW
Terminal
ON-VEHICLE SERVICE
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER
INSPECTION
Front Wiper and Washer Switch (in Combination Switch)
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
B3+2+1AsB3+2+1As
OFFB3WINTB3W
LOOFF
HION
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
Wiper Motor
1) As illustrated, use a 12 V battery to connect its (+) terminal to ter-
minal ªAº, and its (±) terminal to Black lead wire (2) (Type A, B)
or terminal ªEº (Type C).
If motor (1) rotates at a low revolution speed of 45 to 55 rpm, it
is proper. For high speed check, connect battery (+) terminal to
terminal ªBº, and its (±) terminal to Black lead wire (2) (Type A,
B) or terminal ªEº (Type C). If motor rotates at a high revolution
speed of 67 to 83 rpm, it is proper.

YH4
GRAND
VITARA
1. Heat wire
2. Tin foil
3. Tester probe
1. VoltmeterAt center
Good
Broken
wire
broken
wire
8D-16 WINDOWS, MIRRORS, SECURITY AND LOCKS
REAR WINDOW DEFOGGER (IF EQUIPPED)
INSPECTION
DEFOGGER SWITCH
Check for continuity between terminals at each switch position as
shown below.
If check result is not as specified, replace switch.
DEFOGGER WIRE
NOTE:

When cleaning rear window glass, use a dry cloth to wipe it
along wire direction.

When cleaning glass, do not use detergent or abrasive-con-
taining glass cleaner.

When measuring wire voltage, use a tester with negative
probe wrapped with a tin foil which should be held down on
wire by finger pressure.
1) Checking wire damage
a. Turn main switch ON.
b. Turn defogger switch ON.
c. Use a voltmeter to check voltage at the center of each heat
wire, as shown.
Voltage
Criteria
Approx. 5 VGood (No break in wire)
Approx. 10 V or 0 VBroken wire
If measured voltage is 10 V, wire must be damaged between
its center and positive end. If voltage is zero, wire must be
damaged between its center and ground.

YH4
GRAND
VITARA
1. Masking tape
2. Wood spatula
3. Broken wire
4. Repair agent
Several volts
0 volt
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-17
2) Locating damage in wire
a. Touch voltmeter positive (+) lead to heat wire positive termi-
nal end.
b. Touch voltmeter negative (±) lead with a foil strip to heat wire
positive terminal end, then move it along wire to the negative
terminal end.
c. The place where voltmeter fluctuates from zero to several
volts is where there is damage.
NOTE:
If heat wire is free from damage, voltmeter should indicate
12 V at heat wire positive terminal end and its indication
should decrease gradually toward zero at the other terminal
(ground).
REPAIR
DEFOGGER CIRCUIT
1) Use white gasoline for cleaning.
2) Apply masking tape at both upper and lower sides of heat wire
to be repaired.
3) Apply commercially-available repair agent with a fine-tip brush.
4) Two to three minutes later, remove masking tapes previously
applied.
5) Leave repaired heat wire as it is for at least 24 hours before oper-
ating defogger again.

YH4
GRAND
VITARA
8G
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-1
GENERAL DESCRIPTION8G- 2 . . . . . . . . . . . . . .
Ignition Key 8G- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Coil Antenna 8G- 3. . . . . . . . . . . . . . . . . . . . . . . . .
Immobilizer Control Module 8G- 4. . . . . . . . . . . .
ECM/PCM 8G- 4. . . . . . . . . . . . . . . . . . . . . . . . . . .
On-Board Diagnostic System
(Self-Diagnosis Function) 8G- 4. . . . . . . . . . . . .
DIAGNOSIS8G- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions in Diagnosing Troubles 8G- 6. . . . .
Diagnostic Flow Table with monitor coupler> 8G- 9. . . . . . . . . . . . . . . .
Diagnostic Flow Table equipped with monitor coupler> 8G-10. . . . . . .
Diagnostic Trouble Code Check
(Immobilizer Control Module) 8G-11. . . . . . . .
Diagnostic Trouble Code Check
(ECM / PCM) 8G-11. . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code Table 8G-13. . . . . . . . .
TABLE A DTC is not Output
from Diagnostic Output Terminal 8G-14. . . . . . .
TABLE B Immobilizer Indicator Lamp
Check (Immobilizer Indicator Lamp
does not Light at Ignition Switch ON) 8G-15. . .
TABLE C Immobilizer Indicator Lamp
Check (Immobilizer Indicator Lamp
Remains on after Engine Starts) 8G-16. . . . . . .
DTC11 Transponder Code Not Matched8G-17 . .
DTC31 Transponder Code Not
Registered 8G-17. . . . . . . . . . . . . . . . . . . . . . . . .
DTC12 Fault in Immobilizer
Control Module 8G-17. . . . . . . . . . . . . . . . . . . . . .
DTC13 No Transponder Code Transmitted
or Coil Antenna Opened/Shorted 8G-18. . . . . . DTC21 ECM/Immobilizer Control Module
Code Not Matched (Immobilizer Control
Module Side) 8G-20. . . . . . . . . . . . . . . . . . . . . . .
DTC81 (P1623) ECM/Immobilizer
Control Module Code Not Matched
(ECM/PCM Side) 8G-20. . . . . . . . . . . . . . . . . . . .
DTC84 (P1620) ECM/Immobilizer Control
Module Code Not Registered 8G-20. . . . . . . . .
DTC22 Ignition Switch Circuit Open/Short8G-21 . .
DTC23 No ECM/Immobilizer Control
Module Code Transmitted from ECM/
PCM or DLC Circuit Opened/Shorted8G-22 . . . .
DTC83 (P1621) No ECM/Immobilizer
Control Module Code Transmitted from
Immobilizer Control Module or DLC
Circuit Opened/Shorted 8G-22. . . . . . . . . . . . . .
DTC82 (P1622) Fault in ECM/PCM 8G-23. . . . .
Inspection of ECM/PCM, Immobilizer
Control Module and Its Circuit 8G-24. . . . . . . . .
Voltage Check 8G-24. . . . . . . . . . . . . . . . . . . . .
Resistance Check 8G-25. . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8G-26 . . . . . . . . . . . . . . . .
Precautions in Handling Immobilizer
Control System 8G-26. . . . . . . . . . . . . . . . . . . . .
Immobilizer Control Module 8G-27. . . . . . . . . . . .
Coil Antenna 8G-27. . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO REGISTER IGNITION KEY8G-28 . . . . .
PROCEDURE AFTER IMMOBILIZER
CONTROL MODULE REPLACEMENT8G-29 . .
PROCEDURE AFTER ECM/PCM
REPLACEMENT8G-30 . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS8G-30 . . . . . . . . . . . . . . . . . . . . . .
SECTION 8G
IMMOBILIZER CONTROL SYSTEM
(IF EQUIPPED)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
1. Coil antenna
2. Ignition key
3. Immobilizer control module
4. Data link connector (DLC)
5. Immobilizer diagnostic coupler Ignition key
Transponder
code
Immobilizer
Control
ModuleECM/
PCM
8G-2 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
GENERAL DESCRIPTION
The immobilizer control system designed to prevent vehicle burglar consists of following components.

Engine control module (ECM) / Powertrain control module (PCM)

Immobilizer control module

Ignition key (with built-in transponder)

Coil antenna
Operation of this system is as follows.
(1) Each ignition key has its own code (Transponder code) stored in memory. When the ignition switch is turned
ON, Immobilizer Control Module tries to read the Transponder code through the coil antenna installed to the
steering lock assembly.
(2) Immobilizer Control Module compares the Transponder code read in (1) and that registered in Immobilizer Con-
trol Module and checks if they match.
(3) When it is confirmed that two Transponder codes match each other as described above, Immobilizer Control
Module and ECM / PCM check if ECM/Immobilizer Control Module codes registered in them respectively match.
(4) Only when it is confirmed that ECM/Immobilizer Control Module codes match, the engine starts running. If
Transponder codes in Step (2) or ECM/Immobilizer Control Module codes in Step (3) do not match, ECM / PCM
will stop operation of the injector and ignition of spark plug.