Windshield SUZUKI GRAND VITARA 2000 2.G Service User Guide

YH4
GRAND
VITARA
1. Fastener
ªaº: Approx. 5mm (0.197 in.)
1. Mark mating marks
2. Glass
3. Body
4. Molding
1. Do not apply primer
2. Primer
3. Apply primer
4. Old adhesive
1. Molding
2. Glass
BODY SERVICE 9-9
INSTALLATION
1) Using cleaning solvent, clean windshield edge where wind-
shield glass is to be adhered. (Let it dry for more than 10 min-
utes.)
2) Install new glass stoppers (2pcs.) to lower side of windshield and
new fastener to body.
When reusing wind shield, install new fastener to wind shield.
3) To determine installing position of glass to body, position glass
against body so that clearance between upper end of glass and
body is about 5 mm (0.197 in.) and clearances between each
side end (right & left) of glass and body are even. Place glass so
that lug of fastener is matched with cut in body and fit fastener.
Then mark mating marks on glass and body as shown.
Upper clearance can be adjusted by moving stoppers position.
4) Clean contact surfaces of old adhesive, paint or bare metal thor-
oughly.
If surfaces of paint or bare metal come out, apply primer for body
with caution not to apply primer to surface of adhesive remaining
on body.
NOTE:

Be sure to refer to primer maker's instruction for proper
handling and drying time.

Do not touch body and old adhesive surfaces where glass
is to be adhered.
5) Install new molding to glass.
6) Clean glass surface to be adhered to body with clean cloth. If
cleaning solvent is used, let it dry for more than 10 minutes.
Cleaning Area
Distance from the edge of glass or molding
ªaº: 30 ± 50 mm (1.18 ± 1.97 in.)

YH4
GRAND
VITARA
BODY SERVICE 9-11
11) Check for water leakage by pouring water over windshield
through hose. If leakage is found, dry windshield and fill leaky
point with adhesive. If water still leaks even after that, remove
glass and start installation procedure all over again.
CAUTION:
Upon completion of installation, note the following.

Do not use high pressure water.

Do not blow compressed air directly at adhesive ap-
plied part when drying.

Do not use infrared lamp or like for drying.

Sudden closing of door before adhesive is completely
set may cause glass to become loose or to come off.
Therefore, if door is opened or closed before adhesive
is completely set, make sure to open all door glasses
and use proper care.

If molding is not securely in place, hold it down with
a tape until adhesive is completely set.

Each adhesive has its own setting time.
Be sure to refer to its maker's instruction, check set-
ting time of adhesive to be used and observe precau-
tions to be taken before adhesive is set.

Refrain from driving till adhesive is completely set so
as to ensure proper and sufficient adhesion.

YH4
GRAND
VITARA
BODY SERVICE 9-15
1. Fastener
2. Glass
3. Molding
4. Adhesive
5. Primer
QUARTER WINDOW
REMOVAL AND INSTALLATION
Refer to ªWINDSHIELDº section as removal and installation proce-
dures and cautions are basically the same. However, note the fol-
lowing.
NOTE:

Before applying primer to glass edge, install molding ac-
cording to installing position shown in figure.

Observe following precautions when applying adhesive
along glass edge.
±Adhesive should be applied evenly especially in height.
±Be careful not to damage primer.
±Press glass against body quickly after adhesive is applied.
Height ªbº : 12 mm (0.47 in.)
Width ªdº : 16 mm (0.63 in.)
ªcº : 8 mm (0.31 in.)
Clearance ªeº : 1 mm (0.04 in.)

YH4
GRAND
VITARA
9-16 BODY SERVICE
1. Molding
2. Glass
3. Fastener
1. Molding
2. Glass
3. Primer
4. Adhesive
5. Fastener
1. Door sealing cover
BACK DOOR GLASS
REMOVAL AND INSTALLATION
Refer to ªWINDSHIELDº section as removal and installation proce-
dures and cautions are basically the same. However, note the fol-
lowing.
NOTE:

Before applying primer to glass edge, install molding ac-
cording to installing position shown in figure.

Observe following precautions when applying adhesive
along glass edge.
±Adhesive should be applied evenly especially in height.
±Be careful not to damage primer.
±Press glass against body quickly after adhesive is applied.
Height ªbº : 15 mm (0.59 in.)
Width ªcº : 8 mm (0.31 in.)
Width ªdº : 16 mm (0.63 in.)
Clearance ªeº : 1 mm (0.04 in.)

When replacing back door, coat replacement door inside
with wax for proper anticorrosive treatment. Refer to ªUN-
DER COATING / ANTI-CORROSION COMPOUND APPLICA-
TION AREAº in this section.

Apply sealing compound to peripheral of door hem area and
reinstall door sealing cover.

When weatherstrip is hardened and water leaks have devel-
oped, replace it.

YH4
GRAND
VITARA
ªh ± h'º : 1521 mm (59.88 in.)
ªh ± oº : 901 mm (35.47 in.)
ªi ± i'º : 1547 mm (60.91 in.)
ªj ± nº : 806 mm (31.73 in.)
ªj ± j'º : 1511 mm (59.49 in.)
ªj ± oº : 649 mm (25.55 in.)
ªk ± k'º : 1126 mm (44.33 in.)
ªk ± oº : 1350 mm (53.15 in.)
ªl ± l'º : 1491 mm (58.70 in.)
ªl ± oº : 1130 mm (44.49 in.)
ªm ± m'º: 939 mm (36.97 in.)
ªm ± oº : 1725 mm (67.91 in.) Hole to hole distance
ªa ± cº : 982 mm (38.66 in.)
ªb ± b'º : 1390 mm (54.72 in.)
ªb ± c'º : 1406 mm (55.35 in.)
ªb ± cº : 755 mm (29.72 in.)
ªc ± c'º : 1012 mm (39.84 in.)
ªd ± d'º : 1545 mm (60.83 in.)
ªd ± nº : 800 mm (31.50 in.)
ªe ± e'º : 1110 mm (43.70 in.)
ªe ± nº : 1036 mm (40.79 in.)
ªf ± f'º : 1511 mm (59.49 in.)
ªf ± nº : 620 mm (34.41 in.)
ªg ± g'º : 1085 mm (42.72 in.)
ªg ± oº : 1099 mm (43.27 in.)
a. Garnish installation clip hole
b (b'). Front end of front windshield lower installation section
c (c'). Front end of front windshield upper installation section
d. Hole in F door lower hinge at rear
e. Trim installation clip hole
f (f'). Scuff installation hole (at rearmost end)
g (g'). Trim installation hole
h (h'). Hole in R door upper hinge in upper part
i (i'). Hole in R door lower hinge in lower part
j (j'). Rear scuff installation hole (at front end)
k (k'). Trim installation hole
l (l'). R door striker lower section installation hole
m (m'). Trim installation hole
n. Installation hole for F seat front inside
o. Installation hole for F seat rear inside
Opposite side of the point shown in figure
BODY SERVICE 9-27
4 door model

YH4
GRAND
VITARA
Hole to hole distance
a ± c : 981 mm (38.62 in.)
b ± b' : 1390 mm (54.72 in.)
b ± c' : 1404 mm (55.28 in.)
c ± c' : 1008 mm (39.69 in.)
e ± e' : 1110 mm (43.70 in.)
e ± i : 1036 mm (40.79 in.)
f ± i : 688 mm (27.09 in.)g ± g' : 1145 mm (45.08 in.)
g ± h : 1017 mm (40.04 in.)
g ± j : 1078 mm (42.44 in.)
h ± h' : 1338 mm (52.68 in.)
h ± j : 1459 mm (57.44 in.)
j ± k : 548 mm (21.57 in.)
l ± l' : 956 mm (37.64 in.)
a. Garnish installation clip hole
b (b'). Front end of front windshield lower installation section
c (c'). Front end of front windshield upper installation section
d. Hole in F door lower hinge at rear
e. Trim installation clip hole
f (f'). Scuff installation hole (at rearmost end)
g (g'). Trim installation hole
h (h').
11 jig hole
i. Installation hole for F seat front inside
j. Installation hole for F seat rear inside
k (k'). F seat belt installation hole
l (l'). Innermost end of side body installation section
9-30 BODY SERVICE
2 door model

YH4
GRAND
VITARA
Driver side for left hand steering vehicle
Driver side for right hand steering vehicle
1. Stretch deployment harness to its full length
10 m (33 ft).
2. Drop cloth, blanket or similar item2
10B-80 AIR BAG SYSTEM
8) Route deployment harness out the vehicle.
9) Verify that the inside of the vehicle and the area surrounding
the vehicle are clear of all people and loose or flammable ob-
jects.
10) Stretch the deployment harness to its full length 10 m (33 ft).
11) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
12) Completely cover windshield area and front door window
openings with a drop cloth, blanket to similar item. This reduces
the possibility of injury due to possible fragmentation of the ve-
hicle's glass or interior.
13) Notify all people in the immediate area that you intend to deploy
the air bag (inflator) module.
NOTE:

When the air bag deploys, the rapid gas expansion will
create a substantial report. Wear suitable ear protection.
Notify all people in the immediate area that you intend to
deploy the air bag (inflator) module and suitable ear
protection should be worn.

After the air bag (inflator) module has been deployed, the
surface of the air bag may contain a powdery residue.
This powder consists primarily of cornstarch (used to lu-
bricate the bag as it inflates) and byproducts of the
chemical reaction.
WARNING:
Safety precautions must be observed when handling a
deployed air bag (inflator) module.

After deployment, the metal surfaces of the air bag (infla-
tor) module will be very hot. Do not touch the metal areas
of the air bag (inflator) module for about 30 minutes after
deployment.

Do not apply water, oil, etc. to deployed air bag (inflator)
module.

If the deployed air bag (inflator) module must be moved
before it is cool, wear gloves and handle by the air bag or
vinyl trim.
Failure to follow procedures may result in fire or personal
injury.

YH4
GRAND
VITARA
1. Shorted
Driver side for left hand steering vehicle
Driver side for right hand steering vehicle
1. Stretch deployment harness
to its full length 10 m (33 ft).
2. Drop cloth, blanket or similar item.
10B-90 AIR BAG SYSTEM
5) Check that there is no open/short or damage in special tool (de-
ployment harness). If any faulty condition is found, do not use
it and be sure to use new deployment harness.
Special Tool
(A): 09932-75030
6) Short the two deployment harness leads together by fully seat-
ing one banana plug into the other.
WARNING:
Deployment wires shall remain shorted and not be con-
nected to a power source until the pretensioner is to be
activated.
Special Tool
(A): 09932-75030
7) Connect the deployment harness connector to the seat belt
pretensioner harness and lock the connector with lock lever.
Special Tool
(A): 09932-75030
8) Route deployment harness out the vehicle.
9) Verify that the inside of the vehicle and the area surrounding
the vehicle are clear of all people and loose or flammable ob-
jects.
10) Stretch the deployment harness to its full length 10 m (33 ft).
11) Place a power source near the shorted end of the deployment
harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.
12) Completely cover windshield area and front door window
openings with a drop cloth, blanket to similar item. This reduces
the possibility of injury due to possible fragmentation of the ve-
hicle's glass or interior.
13) Notify all people in the immediate area that you intend to acti-
vate the seat belt pretensioner.