Cooling system SUZUKI GRAND VITARA 2000 2.G Service Owner's Manual

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-31
Brake pedal Released Depressed
Voltage 0 VBattery
voltage
DIAGNOSTIC FLOW TABLE A-1 (NO TCC LOCK-UP OCCURS)
SYSTEM DESCRIPTION
PCM turns TCC solenoid OFF under any of the following conditions.

Brake pedal switch: ON

4WD LOW switch: ON

Cruise control module: TCC OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor, its
circuit or engine cooling
system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-8 (G16 / J20 engines) or C51-1-2 (H25
engine) terminal of PCM coupler and ground.

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Brake pedal released.

Drive vehicle with TCC ON condition
referring to ªTCC lock-up diagramº in
this section.
Is it battery voltage?Faulty TCC solenoid
valve, its circuit or
transmission.Go to Step 4.
4Is vehicle equipped with H25 engine?Go to Step 5.Go to Step 6.
5Brake switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-31 terminal of PCM coupler
terminal and ground.
Is the result as specified?Go to Step 6.Faulty brake pedal switch
or its circuit.
If OK, substitute a known-
good PCM and recheck.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-33
O / D cut
switchOFF ON
VoltageBattery
voltage0 V
DIAGNOSTIC FLOW TABLE A-2 (NO GEAR SHIFT TO O / D)
SYSTEM DESCRIPTION
PCM does not shift to O / D gear under any of the following conditions.

O / D cut switch: ON

4WD LOW switch: ON

Cruise control module: O / D OFF command signal is output (if equipped).

ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor,
its circuit or engine
cooling system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-2 (G16 / J20 engines) or C51-1-6 (H25
engine) terminal of PCM coupler and ground,
C51-1-1 terminal of PCM coupler and ground.

O / D cut switch OFF (ªO / D OFFº lamp OFF).

Normal mode in ªDº range.

Transfer ª2Hº position.

Cruise control is not operated (if equipped).

Drive vehicle with 4th gear condition
referring to ªGear shift diagramº in this
section.
Is each voltage about 0 V?Faulty shift solenoid
valve, its circuit or
transmission.ªGº wire or ªG / Rº wire
shorted to power circuit.
If OK, go to Step 4.
4O / D cut switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-33 (G16 / J20 engines) or
E61-14 (H25 engine) terminal of PCM
coupler and ground.
Is the result as specified?Go to Step 5.Faulty O / D cut switch or
its circuit.
If OK, substitute a known-
good PCM and recheck.