engine repair SUZUKI GRAND VITARA 2000 2.G Service Owner's Manual

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-27
A / T BASIC CHECK
This inspection is important for troubleshooting when PCM (ECM) has detected no DTC and no abnormality has
been noted in visual inspection.
Follow flow table carefully.
STEP
ACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Perform MANUAL ROAD TEST in this section.
Is it OK?Go to Step 3.Go to Step 4.
3Proceed to TROUBLE DIAGNOSIS TABLE 1 in this
section.
Is trouble identified?Repair or replace
defective parts.Go to Step 5.
4Perform stall test, time rag test, line pressure test,
engine brake test and ªPº range test referring to STALL
TEST, LINE PRESSURE TEST, ENGINE BRAKE
TEST and ªPº RANGE TEST in this section.
Are the test results satisfactory?Go to Step 5.Proceed to
TROUBLE DIAGNO-
SIS TABLE 3 in this
section.
5Proceed to TROUBLE DIAGNOSIS TABLE 2 in this
section.
Is trouble identified?Repair or replace
defective parts.Proceed to
TROUBLE DIAGNO-
SIS TABLE 3 in this
section.

YH4
GRAND
VITARA
7B1-28 AUTOMATIC TRANSMISSION (4 A / T)
Transmission fluid Running condition Running condition Gear shift
TROUBLE DIAGNOSIS TABLE 1
ConditionPossible CauseCorrection
TCC does not operate
Brake pedal (stop lamp) switch or its
circuit faulty (H25 engine only)

4WD low switch or its circuit faulty

Engine coolant temp. sensor or its
circuit faulty

Cruise control signal circuit faulty
(if equipped)DIAGNOSTIC FLOW TABLE A-1
Gear does not change
to 4th
O / D cut switch or its circuit faulty

4WD low switch or its circuit faulty

Engine coolant temp. sensor or its
circuit faulty

Cruise control signal circuit faulty
(if equipped)DIAGNOSTIC FLOW TABLE A-2
TROUBLE DIAGNOSIS TABLE 2
ConditionPossible CauseCorrection
Low fluid pressure
Clogged oil pump strainer

Malfunction of pressure regulator valveWash strainer.
Overhaul valve body.
High fluid pressure
Pressure regulator valveOverhaul valve body.
Unable to run in all
range
Regulator valve stickReplace.

Clogged oil strainerWash strainer.

Seized or broken planetary gearRepair or replace.

Faulty manual valveReplace.
Poor 1st speed run-
ning or excessive
slippage in ªDº or
ª2º
Faulty 1±2 shift valveReplace.
Poor 1±2 shift, ex-
ili

Regulator valve stickingReplace.
cessive slippage
1±2 shift valve stickingReplace.

Shift solenoid valve-B stickingReplace.

Intermediate coast modulator valve stick-
ingReplace.
Poor 2±3 shift, ex-
ili

2±3 shift valve stickingReplace.
cessive slippage
Shift solenoid valve-A stickingReplace.
Poor start or surg-
ing in ªDº range
Regulator valve stickingReplace.

YH4
GRAND
VITARA
7B1-46 AUTOMATIC TRANSMISSION (4 A / T)
DTC P0741 TCC (LOCK-UP) SOLENOID VALVE PERFORMANCE OR STUCK OFF
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
While running in 2nd or 4th gear, D range, TCC control
of PCM does not agree with actual operation of trans-
mission TCC even though solenoid valve is electrically
in good condition.
(2 driving cycles detection logic)
TCC (lock-up) solenoid valve stuck

TCC control valve stuck

Valve body fluid passage clogged

TCC faulty
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF.
2) Clear DTC, pending DTC and freeze frame data in PCM memory by using scan tool and check fuel level meter
indication is 1/4 or more.
3) Start engine, warm it up to normal operating temperature and shift transfer lever to ª2Hº or ª4Hº range.
4) Increase vehicle speed with D range, and check that gear position changes from 1st to 2nd and keep driving
about 20 mph, 30 km/h in 2nd of ªDº range for 10 seconds. (Throttle valve should be not at idle position and
the opening should be kept constant in this step.)
5) Keep driving about 50 mph, 80 km/h in 4th of ªDº range for 10 seconds.
6) Release accelerator pedal, decrease vehicle speed and stop vehicle.
7) Check pending DTC and DTC by using scan tool.
TROUBLESHOOTING
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2TCC solenoid valve operation check:
1) Check TCC solenoid valve operation referring to
ªSolenoid Valves Operation Checkº in this section.
Is it in good condition?Go to Step 3.Faulty TCC solenoid
valve.
3Valve body check:
1) Check valve body referring to ªUnit Repairº in this
section.
Is it in good condition?Faulty torque
converter.Faulty valve body.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-49
DTC P0751 SHIFT SOLENOID VALVE-A (#1) PERFORMANCE OR STUCK OFF
DTC P0756 SHIFT SOLENOID VALVE-B (#2) PERFORMANCE OR STUCK OFF
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
While running in D range, gear change control from
PCM to A / T does not agree with actual A / T gear posi-
tion even though solenoid valve is electrically in good
condition.
(A / T gear position is calculated based on engine
speed signal and vehicle speed sensor signal.)
(2 driving cycles detection logic)DTC P0751:

Shift solenoid valve-A stuck or leakage.

2-3 shift valve stuck.

Valve body fluid passage clogged.

Mechanical malfunction in transmission.
(Direct clutch malfunction)
DTC P0756:

Shift solenoid valve-B stuck or leakage.

1-2 shift valve stuck.

3-4 shift valve stuck.

Valve body fluid passage clogged.

Mechanical malfunction in transmission.
(2nd brake malfunction)
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF.
2) Clear DTC, pending DTC and freeze frame data in PCM memory by using scan tool and check fuel level meter
indication is 1 / 4 or more.
3) Start engine, warm it up to normal operating temperature and shift transfer lever to ª2Hº or ª4Hº range.
4) Increase vehicle speed with D range, and check that gear position changes from 1st to 2nd, 3rd and 4th in that
order as vehicle speed increases, referring to ªGear Shift Diagramº in this section.
5) Stop vehicle and check pending DTC and DTC by using scan tool.
TROUBLESHOOTING
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Shift solenoid valve-A or -B operation check:
1) Check shift solenoid valve-A or -B for operation
referring to ªSolenoid Valves Operation Checkº
section.
Is it in good condition?Go to Step 3.Faulty shift solenoid
valve-A or -B.
3Valve body check:
1) Check valve body and its passage referring to
ªUnit Repairº section.
Are they in good condition?Overhaul and repair
automatic transmis-
sion.Faulty valve body.

YH4
GRAND
VITARA
1. Dipstick (G16 / J20)
2. Dipstick (H25)
1. Drain plug
2. Propeller shaft
1. Dipstick (G16 / J20)
2. Dipstick (H25)
7B1-60 AUTOMATIC TRANSMISSION (4 A / T)
LEVEL CHECK AT ROOM TEMPERATURE
The fluid level check at room temperature performed after repair or
fluid change before test driving is just preparation for level check of
normal operating temperature. The checking procedure itself is the
same as that described previously. If the fluid level is between FULL
COLD and LOW COLD, proceed to test drive. And when the fluid
temperature has reached the normal operating temperature, check
fluid level again and adjust it as necessary.
FLUID CHANGE
1) Lift up vehicle.
2) With engine is cool, remove drain plug from oil pan and drain A / T
fluid.
3) Install drain plug.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Lower vehicle and fill proper amount of an equivalent of DEX-
RON
-III.
5) Check fluid level according to procedure described under LEV-
EL CHECK NORMAL OPERATING TEMPERATURE.
Fluid specification
An equivalent of DEXRON
-III
Fluid capacity
When draining
from drain plug
hole
2.5 liters (5.28/4.40 US/lmp.pt.)
When
overhauling
6.9 liters (14.58/12.14 US/lmp.pt.)
for G16
7.1 liters (15.00/12.50 US/lmp.pt.)
for J20 / H25

YH4
GRAND
VITARA
7B1-78 AUTOMATIC TRANSMISSION (4 A / T)
ON-VEHICLE
SERVICE MOUNTING
EXTERNAL
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
Fastening portion
Tightening torque
Fastening portion
N´mkg-mlb-ft
Automatic transmission fluid drain plug232.317.0
Transfer oil filler / level and drain plugs232.317.0
Transmission case plug171.712.5
Manual select lever nut131.39.5
Manual select cable nut70.75.5
Manual selector assembly bolts181.813.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts
Engine rear mounting member bolts
Transmission case right stiffener bolts
505.036.5
Universal joint flange bolts and nuts505.036.5
Torque converter mounting bolts656.547.0
Adapter case or extension case bolts
(G16 engine)353.525.5
Adapter case or extension case bolts
(J20 / H25 engines)424.230.0
Transmission range switch lock bolt5.50.554.0
Oil pipe union bolts353.522.5
Drive plate bolts787.856.5
Interlock cable clamp screw2.20.221.5
Interlock cable outer mounting nut131.39.5

YH4
GRAND
VITARA
CLUTCH 7C1-3
DIAGNOSIS
ConditionPossible CauseCorrection
Slipping
Improper clutch pedal free travel.

Worn or oily clutch disc facing.

Warped disc, pressure plate or flywheel
surface.

Weakened diaphragm spring.

Master cylinder piston or seal cup not returning.Bleed air or replace master
cylinder.
Replace disc.
Replace disc, clutch cover or
flywheel.
Replace clutch cover.
Repair master cylinder.
Dragging clutch
Improper clutch pedal free travel.

Weakened diaphragm spring, or worn spring tip.

Rusted input shaft splines.

Damaged or worn splines of transmission
input shaft.

Excessively wobbly clutch disc.

Clutch facings broken or dirty with oil.

Fluid leakage.Bleed air or replace master
cylinder.
Replace clutch cover.
Lubricate.
Replace input shaft.
Replace disc.
Replace disc.
Repair or replace.
Clutch vibration
Glazed (glass-like) clutch facings.

Clutch facings dirty with oil.

Release bearing slides unsmoothly on input
shaft bearing retainer.

Wobbly clutch disc, or poor facing contact.

Weakened torsion springs in clutch disc.

Clutch disc rivets loose.

Distorted pressure plate or flywheel surface.

Weakened or loosened engine mounting
bolt or nut.Repair or replace disc.
Replace disc.
Lubricate or replace input
shaft bearing retainer.
Replace disc.
Replace disc.
Replace disc.
Replace clutch cover or flywheel.
Retighten or replace mounting.
Noisy clutch
Worn or broken release bearing.

Input shaft front bearing worn down.

Excessive rattle of clutch disc hub.

Cracked clutch disc.

Pressure plate and diaphragm spring rattling.Replace release bearing.
Replace input shaft bearing.
Replace disc.
Replace disc.
Replace clutch cover.
Grabbing clutch
Clutch disc facings soaked with oil.

Clutch disc facings excessively worn.

Rivet heads showing out of facing.

Weakened torsion springs.Replace disc.
Replace disc.
Replace disc.
Replace disc.

YH4
GRAND
VITARA
7C1-10 CLUTCH
(B)1
12
(A)
1. Input shaft bearing
2. Flywheel
3. Clutch disc
4. Clutch cover
5. Bolt
6. Release bearing
7. Clutch release fork
8. Boot
9. Clip
10. Clutch release fork support
1. Bolt
2. Clutch cover
1. Input shaft bearing
UNIT REPAIR
CLUTCH COVER, CLUTCH DISC AND FLYWHEEL
DISMOUNTING / REMOUNTING
Refer to SECTION 7A ªDismounting / Remounting of Trans Unitº.
REMOVAL
1) Hold flywheel stationary with special tool (A) and remove clutch
cover bolts, clutch cover and clutch disc.
Special Tool
(A): 09924-17810
2) Pull out input shaft bearing by using special tool (B) and wrench.
Special Tool
(B): 09917-58010 (G16 engine)
(B): 09923-73210 (J20 and H25 engines)
3) Remove release bearing and release fork.

YH4
GRAND
VITARA
7D
TRANSFER 7D-1
The aluminum transfer case directly connected to the
back of the transmission contains the input gear,
countershaft & gear, output rear shaft, output low gear
and output front shaft (for front drive) connected by
way of the hyvo-chain.
The transfer has such a selective mechanism as to
enable the shift control lever to make selection of high
speed (direct connection with transmission output:
main shaft), low speed (speed reduction by input
gear, counter gear and output low gear) or neutral by
way of the reduction sleeve located between input
gear and output low gear, and selection of two-wheel-
drive (high speed only) or four-wheel-drive (high or
low speed) by way of the front drive clutch sleeve lo-cated at the center of the output rear shaft. Also, with
a synchronizer installed to the front drive clutch, it is
possible to change the drive mode between 2WD
(high speed only) and 4WD (high speed only) even
while running.
The front drive shift fork has an auxiliary spring to
make a smooth shift from 4H to 2H possible.
The case has an oil gutter and a plate at synchronizer
to provide proper lubrication even under the strict
conditions of use.
WARNING:
For towing the vehicle for the purpose of repair or
the like, follow the towing instructions in OWN-
ER'S MANUAL.
SECTION 7D
TRANSFER
CONTENTS
GENERAL DESCRIPTION7D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Oil Seals7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer Driven Gear7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Assembly7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismounting7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remounting7D-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION

YH4
GRAND
VITARA
TRANSFER 7D-7
09940-53111
Bearing installer
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Oil filler / level and drain plugs232.317.0
Engine rear mounting bolts505.036.5
Universal joint flange bolts505.036.5
Speed sensor bolt60.64.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)

Oil seal lips and O-rings.

Splines of propeller shaft.

Select return system.

Shift control lever.
SPECIAL TOOL