motor SUZUKI GRAND VITARA 2000 2.G Service Service Manual

YH4
GRAND
VITARA
7B1-74 AUTOMATIC TRANSMISSION (4 A / T)
1. Boot No.2
2. Boot cover
1. Boot clamp
2. Boot No.1
3. Gear shift control lever
1. Boot No.2
2. Transfer shift control
lever
3. Transfer shift lever case4. Transfer shift control
case cover
5. Boot No.1
1. A / T throttle cable
2. Adjusting nut
3. Lock nut
G16 / J20 H25
DISMOUNTING OF TRANSMISSION (WITH
TRANSFER IF EQUIPPED)
IN CABIN
1) Remove console box.
NOTE:
To remove clip, push in its center pin first.
2) Remove boot cover and boot No.2. (if equipped)
3) Remove boot clamp and then remove boot No.1 from transfer
gear shift lever case. (if equipped)
4) With transfer shift control case cover pushed down with fingers,
turn it to counterclockwise and take out shift control lever. (if
equipped)
IN ENGINE ROOM
1) Remove battery, dipstick and oil filler tube.
2) Disconnect A
/
T throttle cable from throttle cam and bracket.
3) Remove starter motor. But don't disconnect its wiring harness.
4) Remove transmission to engine bolt and nut.

YH4
GRAND
VITARA
1. 4WD switch
2. Air pump assembly
3. Pump motor
4. Release valve
5. Pressure switch6. Transfer
7. Front differential
8. Air hose and pipe
9. 4WD indicator lamp
10. To ignition switch
11. ECM or PCM
Operation
(refer to ªComponents and Functionsº)
Power supply
(from ECM or PCM)
DIFFERENTIAL (FRONT) 7E-3
System Circuit and Operation

YH4
GRAND
VITARA
7E-4 DIFFERENTIAL (FRONT)
Components and Functions
ComponentFunction
4WD switch
When the transfer shift lever is shifted to 4L or 4H position, this switch turns ON
and causes the 4WD control system to turn ON, unless it is shifted to N or 2H
within 1 second.
ECM or PCM
When the 4WD switch turns ON [unless it turns OFF within 1 second], this com-
ponent actuates the pump assembly. If the pressure in the air pump assembly
fails to increase higher than the set level even after the pump motor has run more
than 10 seconds, this component stops the motor to protect it.
Air pump assembly

Pump motor

Release valve

Pressure switchThe air pump assembly consists of a pump motor, release valve and a pressure
switch.
Pump motor:
Produces positive pressure which actuates the actuator.
Release valve:
Closes when transfer shift lever is shifted to 4H or 4L so that the positive pressure
is applied to the actuator, and opens when N or 2H to release the pressure to the
atmosphere.
Pressure switch:
Turns ON and OFF depending on the pressure level in the pump assembly
(whether higher or lower than the set pressure level). ECM or PCM detects the
pressure level through this switch.
Differential case assembly

Free axle hub

Axle lock clutch

ActuatorThe free axle hub, axle lock clutch and actuator are installed in the differential
left case. The positive pressure produced in the air pump assembly is applied
to the actuator which then pushes the axle lock clutch to be engaged with the free
axle hub. In this state, the drive force is transmitted to the front axle, resulting in
the 4WD mode.
When the actuator is free from the positive pressure [when it is under the atmo-
spheric pressure], the axle lock clutch is pushed back by the return spring force
and cannot be engaged with the free axle hub, resulting in the 2WD mode.
ª4WDº indicator lampIt lights up when 4WD control system is in the 4WD mode.

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-7
1
1. ECM (PCM); viewed from harness side
4WD CONTROL CIRCUIT INSPECTION
Voltage Check [G16 and J20 engine models]
Check for input or output voltage (voltage between each circuit and
body ground) of ECM (PCM) with ECM (PCM) connector con-
nected and ignition switch turned ON.
TER-
MINALCIRCUITWIRE
COLORNORMAL
VOLTAGECONDITION
E6110 ± 14 VTransfer shift lever: 2H or NE61-
194WD Indicator lampOr / B0 ± 1 V4 seconds after transfer shift lever shifted
to 4H or 4L
C51 2Air pump assembly0 ± 1 VTransfer shift lever: 2H or NC51-2
-7(Pump motor and release
valve)R10 ± 14 V1 seconds after transfer shift lever shifted
to 4H or 4L
C51-24WD switchB/Or10 ± 14 VTransfer shift lever: 2H or N
-184WD switchB/Or0 ± 1 VTransfer shift lever: 4H or 4L
C51-
3-17GroundB/Bl0 ± 1 V±
C51 2Airpumpassembly0 ± 1 VTransfer shift lever: 2H or NC51-2
-27
Air um assembly
(pressure switch)P10 ± 14 V4 seconds after transfer shift lever shifted
to 4H or 4L

YH4
GRAND
VITARA
7E-8 DIFFERENTIAL (FRONT)
1. ECM (PCM); viewed from harness side
Voltage Check [H25 engine model]
TER-
MINALCIRCUITWIRE
COLORNORMAL
VOLTAGECONDITION
C51 110 ± 14 VTransfer shift lever: 2H or NC51-1
-74WD Indicator lampOr / B0 ± 1 V4 seconds after transfer shift lever shifted
to 4H or 4L
C51 1Air pump assembly0 ± 1 VTransfer shift lever: 2H or NC51-1
-15(Pump motor and release
valve)R10 ± 14 V1 seconds after transfer shift lever shifted
to 4H or 4L
C51-14WD switchB/Or10 ± 14 VTransfer shift lever: 2H or N
-114WD switchB/Or0 ± 1 VTransfer shift lever: 4H or 4L
C51-3
-26GroundB/Bl0 ± 1 V±
C51-1Airpumpassembly0 ± 1 VTransfer shift lever: 2H or NC51-1
-18
Air um assembly
(pressure switch)P10 ± 14 V4 seconds after transfer shift lever shifted
to 4H or 4L

YH4
GRAND
VITARA
7E-10 DIFFERENTIAL (FRONT)
1. Plugged hose
2. Adjusting screw
3. Pipe (to air pump assembly)
4. Hose (to differential carrier)
5. Differential housing
4 5
INSPECTION
4WD Control System
1) Install special tool to air hose connecting between air pump as-
sembly and differential (actuator) as shown in figure. Tighten ad-
justing screw of special tool as far as it stops. Close air check
side opening by using fuel hose as blind plug.
Special Tool
(A): 09918-18110
(B): 09367-04002
NOTE:
Use care not to bend any part of hose.
2) Turn ON ignition switch and shift transfer lever from 2H to 4H
range.
3) Check that motor starts running (a sound can be heard) within
1 second and it stops when gauge of special tool indicates speci-
fied pressure value.
Check also for air leakage.
Pressure specification:
30.0 ± 45.0 kPa (0.30 ± 0.45 kg / cm
2, 4.25 ± 6.40 psi)
4) Check that pressure value indicated on gauge of special tool
drops as soon as transfer lever is shifted to 2H position.
5) Start motor by shifting transfer lever to 4H position again. Loos-
en adjusting screw to lower pressure value on gauge. Motor
should start to run again and stop in about 4 seconds.
6) With the adjusting screw of special tool loosened, shift transfer
shift lever to N or 2H position and then 4L or 4H position.
Pump motor should stop about 10 seconds after motor starts to
run.

YH4
GRAND
VITARA
7E-12 DIFFERENTIAL (FRONT)
1. Pump assembly
Air Pump Assembly
Removal / Installation
1) Disconnect air hoses and coupler from air pump assembly.
2) Remove pump assembly by removing bolts.
3) Reverse removal procedure for installation.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
Inspection
1) Install special tool, voltmeter and battery to pump assembly as
shown in figure.
2) Tighten adjusting screw of special tool as far as it stops and
close its air check side opening by using fuel hose as blind plug.
Special Tool
(A): 09918-18110
3) Check that motor starts to run (a sound can be heard) when bat-
tery is connected and it stops when specified pressure is ob-
tained.
Check also for air leakage.
Specified pressure: 30.0 ± 45.0 kPa
(0.30 ± 0.45 kg / cm
2, 4.25 ± 6.40 psi)
4) Check that value indicated on voltmeter is within specification
shown below.
When motor is running: 0 ± 1 V
When motor has stopped running: 10 ± 14 V
CAUTION:
Do not run motor more than 10 seconds continuously to
prevent motor breakage.

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-5
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER
REAR WIPER AND WASHER (IF EQUIPPED)
TroublePossible causeCorrection
Wiper malfunctions
ªWIPER / WASHERº fuse blown (Hard Top
Model)
ªWIPº fuse blown (Canvas Top Model)

Wiper motor faulty

Wiper switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace motor
Replace switch
Repair
Washer malfunctions
Washer hose or nozzle clogged

ªWIPER / WASHERº fuse blown (Hard Top
Model)
ªWIPº fuse blown (Canvas Top Model)

Washer motor faulty

Washer switch faulty

Wiring faultyClean or repair clogged hose or
nozzle
Replace fuse to check for short
Replace motor
Replace switch
Repair
REAR WINDOW DEFOGGER (IF EQUIPPED)
TroublePossible causeCorrection
Defogger does not work
ªREAR DEFGº fuse blown

Defogger switch faulty

Defogger heat wire faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair heat wire
Repair
POWER WINDOW CONTROL SYSTEM
TroublePossible causeCorrection
All power windows do not
operate
ªPOWER WINDOWº fuse blown (Hard Top
Model)
ªP / Wº fuse blown (Canvas Top Model)

Ignition switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
Only one power window
does not operate
Power window switch (main or sub) faulty

Power window motor faulty

Window lock switch faulty

Wiring or grounding faultyReplace switch
Replace motor
Replace switch
Repair

YH4
GRAND
VITARA
8D-6 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR LOCK SYSTEM (IF KEYLESS ENTRY IS NOT EQUIPPED)
TroublePossible causeCorrection
All power doors are not
locked / unlocked by both
driver side door key
switch and power door
lock switch
ªDOOR LOCKº fuse blown (Hard Top
Model)
ªD / Lº fuse blown (Canvas Top Model)

Power door controller faulty

Wiring or grounding faultyReplace fuse to check for short
Replace controller
Repair
All power doors are not
locked / unlocked by only
power door lock switch
Power door lock switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
driver side door key
switch
Driver side door key switch faulty

Wiring or grounding faultyReplace switch
Repair
Only one power door is not
locked / unlocked
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair
Replace actuator

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-7
POWER DOOR LOCK AND KEYLESS ENTRY SYSTEM (IF KEYLESS ENTRY IS
EQUIPPED)
TroublePossible causeCorrection

All power doors are not
locked / unlocked by
both driver side door key
switch and power door
lock switch. But all
power doors are locked /
unlocked by keyless
entry transmitter

All power doors are not
locked / unlocked by
driver side door key
switch, power door lock
switch and keyless entry
transmitter

When power doors are
locked / unlocked by
keyless entry
transmitter, hazard
warning lights do not
flash
ªDOOR LOCKº fuse blown

Power door lock and keyless entry system
faultyReplace fuse to check for short
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
All power doors are not
locked / unlocked by only
power door lock switch
Power door lock switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
driver side door key
switch
Driver side door key switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
keyless entry transmitter
Code registration error

Transmitter battery dead

Transmitter faulty

Power door lock and keyless entry system
faultyRegister code
Replace battery
Replace transmitter
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
Although any door is
opened within 30 seconds
after power door(s)
unlocked by keyless entry
transmitter, all power
doors are locked again
automatically
Door switch faulty

Wiring harness connected to door switch
brakesReplace switch
Repair
Only one power door is not
locked / unlocked
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair
Replace actuator
Operation distance of
keyless entry is unstable
Transmitter battery dead

Transmitter faultyReplace battery
Replace transmitter