fuel type SUZUKI GRAND VITARA 2000 2.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2000, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2000 2.GPages: 801, PDF Size: 12.15 MB
Page 3 of 801
YH4
GRAND
vol.1
0A
0B
1A
1B
3
3A
3B1
3C
3C1
3D
3E
3F
4A2
4B
5
6
7A5A
5B
5C
5E1
6A1
6A2
6A4
6B
6C
6E1
6E2
6F1
6F2
6G
6G1
6H
6K
7A1
7B1
7C1
7D
7E
7F
8
8B
8C
8D
8G
9
10
10A
8A
10B
6-1ENGINE
General Information and
Diagnosis (G16 / J20)
General Information and
Diagnosis (H25)
Engine Mechanical (G16)
Engine Mechanical (H25)
Engine Mechanical (J20)
Engine Cooling
Engine Fuel
Engine and Emission Control
System (SFI for G16 / J20)
Engine and Emission Control
System (SFI for H25)
Ignition System (G16)
Ignition System (J20 / H25)
Cranking System
(Reduction Type)
Cranking System
(No-Reduction Type)
Charging System
Exhaust System
TRANSMISSION, CLUTCH
AND DIFFERENTIAL
Manual Transmission (Type 1)
Manual Transmission (Type 2)
Automatic Transmission
Clutch (Hydraulic Type)
Transfer
Differential (Front)
Differential (Rear)
BODY ELECTRICAL SYSTEM
Wiring Diagram
Lighting System
Instrumentation / Driver
Information
Windows, Mirrors, Security
and Lock
Immobilizer Control System
BODY SERVICE
RESTRAINT SYSTEM
Seat Belt
Air Bag System GENERAL INFORMATION
General Information
Maintenance and Lubrication
TABLE OF CONTENTS TABLE OF CONTENTS SECTIONSECTION
0B
HEATING AND AIR
CONDITIONING
Heater and Ventilation
Air Conditioning
STEERING, SUSPENSION,
WHEELS AND TIRES
Front End Alignment
Power Steering (P / S) System
Steering Wheel and Column
(Not Equipped with Air Bag)
Air Bag Steering Wheel
and Column
Front Suspension
Rear Suspension
Wheel and Tires
1A
3A 0A
1B
3B1
3C
3C1
3D
3E
3F36A16
6A2
6A4
6B
6C
6E1
6E2
6F1
DRIVE SHAFT / PROP. SHAFT
Front Drive Shaft / Shaft
Bearing, Oil Seal
Propeller Shaft
BRAKES
Brake Pipe / Hose / Master
Cylinder
Front Brakes
Parking and Rear Brakes
Antilock Brake System
4A2
4B
5
5A
5B
5C
5E1
6F2
6G
6G1
6H
6K
7A
7A1
7B1
7C1
7D
7E
7F
8
8A
8B
8C
8D
8G
9
10
10A
10B
6-1
NOTE:
The screen toned Sections 6 ± 6K are included in Volume 2 and Section 8A is in Wiring
Diagram Manual.
Page 29 of 801
YH4
GRAND
VITARA
0B-2 MAINTENANCE AND LUBRICATION
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE UNDER NORMAL DRIVING CONDITIONS
Interval:
This interval should be judged by
This table includes services as scheduled up to 90,000 km
(54,000 miles) mileage. Beyond 90,000 km (54,000 miles), carry
out the same services at the same intervals respectively.
This interval should be judged by
odometer reading or months,Km (x 1,000)153045607590g
whichever comes first.Miles (x 1,000)91827364554
Months122436486072
ENGINE
1-1. Drive beltV-beltIRIRIR
V-rib belt (Flat type)±±I±±R
1-2. Camshaft timing belt (G16 engine only)Replace every 100,000 km or
60,000 miles
1-3. Valve lash (clearance)G16 engine only±I±I±I
1-4. Engine oil and
oil filterJ20 / H25 engines
G16 engine with HO2S (SG, SH, SJ)RRRRRR
G16 engine with HO2S (SE, SF),
G16 engine without HO2SReplace every 10,000 km (6,000 miles)
or 8 months
1-5. Engine coolant±±R±±R
1-6. Exhaust system±I±I±I
IGNITION SYSTEM
2-1. Spark plugs
Wh
Vehicle without
HO2S
Nickel plug±R±R±R
When
unleaded
HO2SIridium plug±±±R±±unleaded
fuel isVehicle with
HO2S
Nickel plug±±R±±Rfuel is
usedHO2SIridium plugReplace every 105,000 km or 63,000
miles
When leaded fuel is used, refer to ªSevere Driving Conditionº schedule
FUEL SYSTEM
3-1. Air cleaner filterIIRIIR
3-2. Fuel lines and connections±I±I±I
3-3. Fuel filterReplace every 105,000 km or 63,000
miles
3-4. Fuel tank±±I±±I
EMISSION CONTROL SYSTEM
4-1. Crankcase ventilation hoses and connections
(Vehicle without HO2S)±±I±±I
4-2. PCV valveVehicle without HO2S±±I±±I
Vehicle with HO2S±±±±±I
4-3. Fuel evaporative emission
tl t
Vehicle without HO2S±I±I±I
control systemVehicle with HO2S±±±±±I
NOTES:
ªRº : Replace or change
ªIº : Inspect and correct, replace or lubricate if necessary
For Item 1-2. Camshaft timing belt: This belt may be replaced every 90,000 km (54,000 miles) according
to customer's maintenance convenience.
For Sweden, item 2-1, 4-2 and 4-3 should be performed by odometer reading only.
For Item 2-1. Spark plugs, replace every 50,000 km if the local law requires.
Nickel spark plug: BKR6E-11 or K20PR-U11
Iridium spark plug: IFR6E11 or SK20PR-A11 for G16 engine, IFR5J11 or SK16PR11 for J20 / H25 engines
Page 289 of 801
YH4
GRAND
VITARA
1. Air bleeder plug
2. Weight
3. Attachment2
ªLº
BRAKES 5-13
FLUSHING BRAKE HYDRAULIC SYSTEM
It is recommended that entire hydraulic system be thoroughly
flushed with clean brake fluid whenever new parts are installed in
hydraulic system.
Periodical change of brake fluid is also recommended.
FLUID PRESSURE TEST(if equipped with
LSPV)
Test procedure for LSPV assembly is as follows.
Before testing, confirm the following.
Fuel tank is filled with fuel fully.
Vehicle is equipped with spare tire, tools, jack and jack handle.
1) Stop vehicle on level floor and place approximately about
200 kg (441 lbs) weight on rear housing so that rear axle weight
800 kg (1764 lb).
Rear axle weight ªLº: 800 kg (1764 lb)
2) Install special tool to front and rear brake.
NOTE:
Special tool should be connected to breather of front (driv-
er's side brake) and rear brakes.
Special Tool
Front brake
(A): 09956-02310
(B): 09952-46510 (Attachment for vehicle with SUMITOMO
ELECTRIC brake caliper)
(C): 55473-82030 (Air bleeder plug supplied as a spare part)
Rear brake
(A): 09956-02310
(B): 09952-36310 (Attachment for thread diameter 7 mm of
bleeder plug) or
09952-46510 (Attachment for thread diameter 8 mm of
bleeder plug)
(C): 55473-82030 (Air bleeder plug supplied as a spare part)
NOTE:
Special tool (B) is used instead of thread diameter 10 mm
attachment of special tool (A).
So remove the attachment from (A) and install (B) as
shown in figure.
For vehicle with TOKICO brake caliper, use the attach-
ment included in special tool (A).
For identification of brake caliper type, refer to GENERAL
DESCRIPTION in SECTION 5B.