Pressure sensor SUZUKI GRAND VITARA 2001 2.G Owner's Guide

6-1-76 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0171/P0172 Fuel System Too Lean/Rich (Bank 1)
DTC DETECTING CONDITION AND POSSIBLE CAUSE
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and warm up
engine completely.
3) Increase vehicle speed to 50 – 60 km/h (30 – 40 mph).
4) Keep driving above vehicle speed for 3 min. or more.
5) Stop vehicle and check pending DTC by using scan tool.DTC DETECTING CONDITION TROUBLE AREA
When running after engine warmed (2 driving cycle
detection logic).
• Short term fuel trim exceeding 15 % or long term fuel
trim exceeding 20 % and total trim exceeding 43 % is
detected.
– Fuel system too lean
• Short term fuel trim less than – 11 % or long term fuel
trim less than – 11 % and total trim less than – 30 % is
detected.
– Fuel trim too rich• Vacuum leaks (air inhaling)
• Exhaust gas leakage
• Fuel pressure out of specification
• Heated oxygen sensor malfunction
• EGR system malfunction
• MAF sensor poor performance
• ECT sensor poor performance
• Fuel level sensor.
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. at start : – 8 – 60°C (18 – 140°F)
Engine coolant temp. at start : – 8 – 95°C (18 – 203°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : 110°C (230°F) or lower

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-77
TROUBLESHOOTING
Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” per-
formed?Go to Step 2. Go to “ENGINE DIAG.
FLOW TABLE” in this
section.
2 Is there DTC (s) other than “DTC P0171/
P0172”?Go to applicable DTC
FLOW TABLE.Go to Step 3.
3 Check intake system and exhaust system for
leakage.
Are intake system and exhaust system in good
condition?Go to Step 4. Repair or replace.
4 Check fuel pressure referring to “TABLE B-3” in
this section.
Is check result satisfactory?Go to Step 5. Repair or replace.
5 Check fuel injectors referring to “FUEL INJEC-
TOR INSPECTION” in Section 6E2.
Is check result satisfactory?Go to Step 6. Faulty injector (s).
6 Check fuel level sensor referring to “FUEL
LEVEL SENSOR” in Section 6E2.
Is check result satisfactory?Go to Step 7. Faulty fuel level sensor or
its circuit.
7 Check MAF sensor for performance referring to
“MASS AIR FLOW SENSOR” in Section 6E2.
Is check result satisfactory?Go to Step 8. Faulty MAF sensor or its
circuit.
8 Check ECT sensor referring to Section 6E2.
Is check result satisfactory?Go to Step 9. Faulty ECT sensor.
9 Check HO2S-1 referring to “DTC P0130 DIAG.
FLOW TABLE”.
Is check result satisfactory?Substitute a known-good
ECM (PCM) and recheck.Faulty HO2S-1.

6-1-78 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0174/P0175 Fuel System Too Lean/Rich (Bank 2)
DTC DETECTING CONDITION AND POSSIBLE CAUSE
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and warm up
engine completely.
3) Increase vehicle speed to 50 – 60 km/h (30 – 40 mph).
4) Keep driving above vehicle speed for 3 min. or more.
5) Stop vehicle and check pending DTC by using scan tool.DTC DETECTING CONDITION TROUBLE AREA
When running after engine warmed (2 driving cycle
detection logic).
• Short term fuel trim exceeding 15 % or long term fuel
trim exceeding 20 % and total trim exceeding 43 % is
detected.
– Fuel system too lean
• Short term fuel trim less than – 11 % or long term fuel
trim less than – 11 % and total trim less than – 30 % is
detected.
– Fuel trim too rich• Vacuum leaks (air inhaling)
• Exhaust gas leakage
• Fuel pressure out of specification
• Heated oxygen sensor malfunction
• EGR system malfunction
• MAF sensor poor performance
• ECT sensor poor performance
• Fuel level sensor.
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. at start : – 8 – 60°C (18 – 140°F)
Engine coolant temp. at start : – 8 – 95°C (18 – 203°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : 110°C (230°F) or lower

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-79
TROUBLESHOOTING
Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” per-
formed?Go to Step 2. Go to “ENGINE DIAG.
FLOW TABLE” in this
section.
2 Is there DTC (s) other than “DTC P0174/
P0175”?Go to applicable DTC
FLOW TABLE.Go to Step 3.
3 Check intake system and exhaust system for
leakage.
Are intake system and exhaust system in good
condition?Go to Step 4. Repair or replace.
4 Check fuel pressure referring to “TABLE B-3” in
this section.
Is check result satisfactory?Go to Step 5. Repair or replace.
5 Check fuel injectors referring to “FUEL INJEC-
TOR INSPECTION” in Section 6E2.
Is check result satisfactory?Go to Step 6. Faulty injector (s).
6 Check fuel level sensor referring to “FUEL
LEVEL SENSOR” in Section 6E2.
Is check result satisfactory?Go to Step 7. Faulty fuel level sensor or
its circuit.
7 Check MAF sensor for performance referring to
“MASS AIR FLOW SENSOR” in Section 6E2.
Is check result satisfactory?Go to Step 8. Faulty MAF sensor or its
circuit.
8 Check ECT sensor referring to Section 6E2.
Is check result satisfactory?Go to Step 9. Faulty ECT sensor.
9 Check HO2S-1 referring to “DTC P0150 DIAG.
FLOW TABLE”.
Is check result satisfactory?Substitute a known-good
ECM (PCM) and recheck.Faulty HO2S-1.

6-1-80 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0300/P0301/P0302/P0303/P0304/P0305/P0306 Random Misfire/Cylinder
1 Misfire/Cylinder 2 Misfire/Cylinder 3 Misfire/Cylinder 4 Misfire Detected/Cyl-
inder 5 Misfire Detected/Cylinder 6 Misfire Detected
SYSTEM DESCRIPTION
ECM (PCM) measures the angle speed of the crankshaft based on the pulse signal from the CKP sensor and
CMP sensor for each cylinder. If it detects a large change in the angle speed of the crankshaft, it concludes
occurrence of a misfire. When the number of misfire is counted by the ECM (PCM) beyond the DTC detecting
condition, it determines the cylinder where the misfire occurred and outputs it as DTC.
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and start
engine.
3) Increase vehicle speed to speed recorded as freeze frame data (V) ± 5 km/h when detecting misfire.
4) Keep driving above vehicle speed for 5 min.
5) Stop vehicle and check DTC (or pending DTC) by using scan tool.DTC DETECTING CONDITION TROUBLE AREA
DTC P0300 :
• Misfire which causes catalyst to overheat during 200 engine
revolutions is detected at 2 or more cylinders. (MIL flashes as
long as this misfire occurs continuously.)
• Misfire which affects exhaust emission adversely during 1000
engine revolutions is detected at 2 or more cylinders (2 driving
cycle detection logic)• Ignition system
• Fuel injector and its circuit
• Fuel line pressure
• Engine compression
• Abnormal air drawn in
• EGR system
• Fuel level sensor
• Valve lash adjuster
• Valve timing DTC P0301, P0302, P0303, P0304, P0305, P0306 :
• Misfire which causes catalyst to overheat during 200 engine
revolutions is detected at 1 cylinder. (MIL flashes as long as
this misfire occurs continuously.)
• Misfire which affects exhaust emission adversely during 1000
engine revolutions is detected at 1 cylinder
(2 driving cycle detection logic)
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. : – 8 – 70°C (18 – 158°F)
Engine coolant temp. : – 8°C (18°F) or higher
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-81
TROUBLESHOOTING
Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” per-
formed?Go to Step 2. Go to “ENGINE DIAG.
FLOW TABLE” in this
section.
2 Ignition system inspection :
1) Check spark plug and ignition spark of cylin-
der where misfire occurs, referring to “IGNI-
TION SYSTEM” section.
Is it in good condition?Go to Step 3. Faulty ignition coil, wire
harness, or other system
parts.
3 Fuel injector circuit inspection :
1) Using sound scope, check each injector
operating sound at engine cranking or
idling.
Do all injectors make operating sound?Go to Step 4. Check coupler connec-
tion and wire harness of
injector not making oper-
ating sound and injector
itself.
If OK, substitute a known-
good ECM (PCM) and
recheck.
4 Fuel pressure inspection :
1) Check fuel pressure referring to “TABLE B-
3” in this section.
Is check result satisfactory?Go to Step 5. Repair or replace.
5 Fuel injector inspection :
1) Check fuel injector(s) referring to Section
6E2.
Is check result satisfactory?Go to Step 6. Replace.
6 Ignition timing inspection :
1) Check ignition timing referring to Section
6F2.
Is check result satisfactory?Go to Step 7. Adjust or check system
related parts.
7 EGR system inspection :
1) Check EGR system referring to Section
6E2.
Is check result satisfactory?Go to Step 8. Repair or replace.
8 Fuel level sensor inspection :
1) Check fuel level sensor referring to Section
6E2.
Is check result satisfactory?Go to Step 9. Repair or replace.
9 Check engine mechanical parts or system
which can cause engine rough idle or poor per-
formance.
• Engine compression (See Section 6A2).
• Valve lash or lash adjuster (See Section
6A2).
• Valve timing (Timing belt or chain installa-
tion. See Section 6A2).
Are they in good condition?Check wire harness and
connection of ECM (PCM)
ground, ignition system
and fuel injector for inter-
mittent open and short.Repair or replace.

6-1-84 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0335 Crankshaft Position Sensor Circuit Malfunction
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and run
engine at idle speed for 10 sec.
3) Check DTC by using scan tool.
1. CKP sensor
2. ECM (PCM)
DTC DETECTING CONDITION TROUBLE AREA
CKP sensor signal is not input while 100 pulses of
CMP sensor signal are input after engine start.CKP sensor circuit
CKP sensor
ECM (PCM)
NOTE:
Check to make sure that following condition is satisfied when using this “DTC CONFIRMATION PRO-
CEDURE”.
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : – 8 – 110°C (18 – 230°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-87
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool.
3) Crank engine for 3 seconds or more and keep it at idle for 1 min.
4) Check DTC by using scan tool.
TROUBLESHOOTING
DTC DETECTING CONDITION TROUBLE AREA
CMP sensor signal is not inputted for 3 sec. even though
engine start signal is being inputted.
or
REF signal pattern is incorrect while POS signal varies.
or
POS signal voltage too high or too low.CMP sensor circuit
CMP sensor
Engine starter signal circuit
ECM (PCM)
NOTE:
Check to make sure that following condition is satisfied when using this “DTC CONFIRMATION PRO-
CEDURE”.
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : – 8 – 110°C (18 – 230°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)
NOTE:
If starter circuit is open (i.e., starter signal circuit is OK but starter fails to run), this DTC is stored in
memory at starter switch ON, even through CMP sensor is in good condition.
When starter motor fails to run and this DTC appears, check starter circuit first.
Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” performed? Go to Step 2. Go to “ENGINE DIAG.
FLOW TABLE” in this
section.
2 Is engine cranked? Go to Step 3. Go to Section 6G.
3 Is there DTC P1500 (Engine starter signal circuit)? Go to DTC P1500 Diag.
Flow Table.Go to Step 4.
4 CMP sensor power supply voltage check :
1) With ignition switch OFF, disconnect CMP sen-
sor coupler.
2) With ignition switch ON, check voltage between
C09-2 and C09-1 terminal. (See Fig.)
Is the voltage 10 – 14 V?Go to Step 5. Faulty “BLU/BLK” wire
and/or “GRY/YEL” wire.

6-1-90 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and warm up
engine completely.
3) Increase vehicle speed to 55 – 60 km/h (35 – 40 mph).
4) Keep driving above vehicle speed for 7 min. or more.
5) Increase vehicle speed to 100 – 110 km/h (60 – 70 mph).
6) Release accelerator pedal and with engine brake applied, keep vehicle coasting and then stop vehicle.
7) Check if pending DTC exists by using scan tool. If not, check if EGR system monitoring test has completed
by using scan tool. If not in both of above checks (i.e., no pending DTC and EGR system monitoring test not
completed), check vehicle conditions (environmental) and repeat Steps 3) through 6).DTC DETECTING CONDITION TROUBLE AREA
During deceleration (engine speed high with closed
throttle position) in which fuel cut is involved, difference
in intake manifold pressure between when EGR valve is
opened and when it is closed is smaller than specified
value.
(2 driving cycle detection logic)•EGR valve
• EGR passage
• Manifold absolute pressure sensor
•ECM (PCM)
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
NOTE:
Check to make sure that following conditions are satisfied when using this “DTC CONFIRMATION
PROCEDURE”.
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : – 8 – 110°C (18 – 230°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)
1. Vehicle speed km/h (mph)
2. Step

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-103
DTC P0460 Fuel Level Sensor Circuit High Input
WIRING DIAGRAM/CIRCUIT DESCRIPTION
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC, pending DTC and freeze frame data by using scan tool and run
engine for 1 min.
3) Check pending DTC by using scan tool.
1. Fuel level sensor
2. Fuel meter in combination meter
3. ECM (PCM)
DTC DETECTING CONDITION TROUBLE AREA
Fuel level sensor output voltage higher than specified
value is detected for specified time.
(2 driving cycle detection logic)•Fuel level gauge or its circuit
•Fuel level sensor or its circuit
•ECM (PCM)
NOTE:
Check to make sure that following condition is satisfied when using this “DTC CONFIRMATION PRO-
CEDURE”.
Intake air temp. : – 8°C (18°F) or higher
Engine coolant temp. : – 8 – 110°C (18 – 230°F)
Altitude (barometric pressure) : 2400 m, 8000 ft or less (560 mmHg (75 kPa) or more)