roof SUZUKI GRAND VITARA 2001 2.G Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2001, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2001 2.GPages: 656, PDF Size: 14.31 MB
Page 552 of 656
BODY SERVICE 9-7
Hole to hole distance :
a. Clip hole in the center of head lining rear installation section e. Installation hole in uppermost part of lower hinge
b (b’). Innermost end of roof panel installation section f (f’). Innermost end of rear floor tail member installation section
c. Installation hole in upper part of back door striker g (g’). Installation hole in outer upper section of rear combination right lamp
d. Installation hole in uppermost part of upper hinge h. Nut hole
b
ba
b’
b’
c
g’
f’
f’
h
f
f
e
g
d
f
b
a – b’ : 448 mm (17.64 in.) b – e : 837 mm (32.95 in.) c – e : 1293 mm (50.90 in.)
a – f’ : 1054 mm (41.50 in.) b – f : 892 mm (35.12 in.) f – f’ : 1030 mm (40.55 in.)
a – g’ : 1050 mm (41.34 in.) b’ – c : 650 mm (25.59 in.) f’ – h : 512 mm (20.16 in.)
a – h : 921 mm (36.25 in.) b’ – f : 1314 mm (51.73 in.) g – g’ : 1544 mm (60.79 in.)
b – b’ : 888 mm (34.96 in.) b’ – h : 996 mm (39.21 in.) g’ – h : 806 mm (31.73 in.)
b – d : 400 mm (15.75 in.) c – d : 1245 mm (49.02 in.)
Page 557 of 656
9-12 BODY SERVICE
1. Rear quarter inner panel 5. Roof panel 9. Air outlet panel
2. Side body outer panel 6. Front pillar upper reinforcement“A” : Apply sealant
3. Back pillar outer panel 7. Rear wheel housing panel“B” : Brush treatment
4. Front pillar inner panel 8. Fuel inlet box
N
“A” (“B”)“A” (“B”)
C
C
“A”5“A”
“A” (“B”)
“A” (“B”)
“A” (“B”)
“A”
“A” “A”2
6
4
117
82
97 2
13
O
U
V X W2“A” (“B”)
A
AB B L
L
“A”
N
C – C
B – BA – A
L – L
VIEW:W
Page 562 of 656
BODY SERVICE 9-17
Undercoating/Anti-corrosion Compound Application Area
“a” : 200 mm (7.87 in.) 1. Side body outer
“b” : 100 mm (3.94 in.) 2. Side sill inner
“A” : Apply rust proof wax (hot wax 50 µm or more) 3. Frame
“B” : Apply rust proof wax (high viscosity wax 50 µm or more) 4. Main floor
5. Side body outer
6. Rear wheel housing
7. Center floor
A
A
B
BD
D
C
“A”“A”
“A”“A”
“A”
“A”5
C
Z
“B”
“B” 3 4
76 2
“a”“b”“a”
1
D – D
C – CB – B
A – A
“B” VIEW: Z
Page 565 of 656
9-20 BODY SERVICE
Rear floor carpet (without third seat vehicle)
REMOVAL
1) Remove rear luggage mat end garnish (1), rear side sill scuff
and rear quarter lower trims (2).
2) Remove luggage hook plate nut (3).
3) Remove rear floor carpet.
INSTALLATION
Reverse removal procedure for installation, noting the following.
Head Lining
REMOVAL
1) Remove front side sill scuffs (1), rear side sill scuffs (2), cen-
ter pillar lower trims (3), center pillar upper trims (4), front pil-
lar upper trims (5) rear luggage mat end garnish (6), rear
luggage box (7), rear quarter lower trims (8) and rear quarter
upper trims (9).
2) Remove rear A/C No.1 duct (1).
3) Remove sliding roof switch and sliding roof trim (if equipped).
4) Remove sun visor assembly (1)
5) Remove map lamp (2), dome lamp (3) and luggage lamp (4).
6) Remove assistant grips (5).
7) Disconnect rear washer hose and roof harness.
8) Remove head lining (6).
1 2
3
4
5
3
1
6
7
8
9
2
1
NOTE:
For without sunroof model.
Adhesive is used in head lining. Clear adhesive from
head lining and roof after removing roof lining.
12
55 346
Page 566 of 656
BODY SERVICE 9-21
INSTALLATION
Reverse removal procedure to install head lining noting the follow-
ing instructions.
•Set roof harness (1) and rear washer hose (2) to head lining
(3) with adhesive tape as shown.
•For without sunroof model
Apply double coated tape (4) to head lining as shown.
•Tighten seat belt anchor bolt as specified torque referring to
Section 10A. CAUTION:
Do not remove rear A/C No.2 duct (1) from head lining (2).
If perform this prohibited service, head lining (2) will be
broken.
13
2
1 4
2