piston SUZUKI GRAND VITARA 2001 2.G Service Owner's Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2001, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2001 2.GPages: 801, PDF Size: 12.15 MB
Page 432 of 801
YH4
GRAND
VITARA
7B1-30 AUTOMATIC TRANSMISSION (4 A / T)
Running condition Gear shift Abnormal
noise
ConditionPossible CauseCorrection
Poor 1st speed run-
ning or excessive
slippage in ªDº or ª2ºFluid pressure leakage from forward clutch
due to wear or breakage of O/D case seal
ringReplace.
Overdrive clutch slippingReplace.
Unable to run or ex-
cessive slippage in
ªLº rangeFluid pressure leakage of forward clutch
due to wear or breakage of O/D case seal
ringReplace.
Reverse brake disc slippingReplace.
Broken brake piston O-ringReplace.
Unable to run or ex-
cessive slippage in
ªRº rangeFluid pressure leakage to direct clutch due
to wear or breakage of center support seal
ringReplace.
Worn direct clutchReplace.
Poor 1±2 shift, ex-
cessive slippageFluid pressure leakage to overdrive clutch
due to wear or breakage of O/D case seal
ringReplace.
Faulty second brakeReplace.
Broken O-ring of second brake pistonReplace.
Faulty second coast brake (in ª2º range)Replace.
Poor 2±3 shift, ex-
cessive slippageFluid pressure leakage to overdrive clutch
due to wear or breakage of O/D case seal
ringReplace.
Worn direct clutch bushingReplace.
Direct clutch slippingReplace.
Foreign material caught in direct clutch pis-
ton check ballReplace.
Poor start or surging
in ªDº rangeFluid pressure leakage of forward clutch
due to wear or breakage of O/D case seal
ringReplace.
Malfunction of forward clutchReplace.
Poor 3±4 shift, ex-
ili
Faulty overdrive brakeReplace.
cessive slippageFaulty overdrive clutchReplace.
Poor start or judder-
ing in ªRº rangeFluid pressure leakage of direct clutch due
to wear or breakage of oil center support
seal ringReplace.
Worn direct clutchReplace.
Excessive shock on
1± 2 shiftFaulty one-way clutchReplace.
Non operate lock-up
systemFaulty torque converterReplace.
Abnormal noise in
ªPº or ªNº rangeWorn oil pumpReplace.
SCAN TOOL DATA-Refer to SECTION 6 / 6-1.
INSPECTION OF PCM AND ITS CIRCUIT-Refer to SECTION 6 / 6-1.
WIRE HARNESS AND CONNECTORS-Refer to SECTION 6 / 6-1.
Page 484 of 801
YH4
GRAND
VITARA
CLUTCH 7C1-3
DIAGNOSIS
ConditionPossible CauseCorrection
SlippingImproper clutch pedal free travel.
Worn or oily clutch disc facing.
Warped disc, pressure plate or flywheel
surface.
Weakened diaphragm spring.
Master cylinder piston or seal cup not returning.Bleed air or replace master
cylinder.
Replace disc.
Replace disc, clutch cover or
flywheel.
Replace clutch cover.
Repair master cylinder.
Dragging clutchImproper clutch pedal free travel.
Weakened diaphragm spring, or worn spring tip.
Rusted input shaft splines.
Damaged or worn splines of transmission
input shaft.
Excessively wobbly clutch disc.
Clutch facings broken or dirty with oil.
Fluid leakage.Bleed air or replace master
cylinder.
Replace clutch cover.
Lubricate.
Replace input shaft.
Replace disc.
Replace disc.
Repair or replace.
Clutch vibrationGlazed (glass-like) clutch facings.
Clutch facings dirty with oil.
Release bearing slides unsmoothly on input
shaft bearing retainer.
Wobbly clutch disc, or poor facing contact.
Weakened torsion springs in clutch disc.
Clutch disc rivets loose.
Distorted pressure plate or flywheel surface.
Weakened or loosened engine mounting
bolt or nut.Repair or replace disc.
Replace disc.
Lubricate or replace input
shaft bearing retainer.
Replace disc.
Replace disc.
Replace disc.
Replace clutch cover or flywheel.
Retighten or replace mounting.
Noisy clutchWorn or broken release bearing.
Input shaft front bearing worn down.
Excessive rattle of clutch disc hub.
Cracked clutch disc.
Pressure plate and diaphragm spring rattling.Replace release bearing.
Replace input shaft bearing.
Replace disc.
Replace disc.
Replace clutch cover.
Grabbing clutchClutch disc facings soaked with oil.
Clutch disc facings excessively worn.
Rivet heads showing out of facing.
Weakened torsion springs.Replace disc.
Replace disc.
Replace disc.
Replace disc.
Page 488 of 801
YH4
GRAND
VITARA
3
4
1. Reservoir cap
2. Cylinder
3. Piston assembly
4. Push rod
5. Piston stopper
6. Circlip
7. Boot
8. Lock nut
9. Clevis
1. Circlip
2. Push rod
3. Piston
4. Cylinder
1. Circlip
2. Push rod
3. Piston stopper
CLUTCH 7C1-7
DISASSEMBLY AND ASSEMBLY CLUTCH
MASTER CYLINDER
DISASSEMBLY
1) Remove boot and then circlip with piston pushed in.
2) Remove push rod and blow compressed air gradually into hole
for pipe connection to remove piston assembly, using care to
prevent it from jumping out.
INSPECTION
Inspect all disassembled parts for wear or damage and replace
parts if necessary.
NOTE:
Wash disassembled parts with brake fluid.
Do not reuse piston assembly and circlip.
Inspect cylinder bore for scoring or corrosion. It is best to replace
corroded cylinder. Corrosion can be identified as pits or excessive
roughness.
NOTE:
Polishing bore of cylinder with anything abrasive is prohib-
ited, as damage to cylinder bore may occur.
Rinse cylinder in clean brake fluid. Shake excess rinsing fluid from
cylinder. Do not use a cloth to dry cylinder, as lint from cloth cannot
be kept away from cylinder bore surfaces.
ASSEMBLY
NOTE:
Before installation, wash each part in specified brake fluid.
1) Apply brake fluid to inside of piston assembly and cylinder body.
2) Install piston assembly into cylinder.
3) With piston pushed down, install circlip as shown.
And install boot.
Page 489 of 801
YH4
GRAND
VITARA
ªAº
1. Reservoir cap
2. Cylinder
3. Piston assembly
4. Push rod
5. Piston stopper
6. Circlip
7. Boot
8. Lock nut
9. Clevis
1. Clutch operating cylinder
2. Hose
3. E-ring
7C1-8 CLUTCH
4) Tighten lock nut to specified torque.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
5) For installation of master cylinder to vehicle, refer to INSTALLA-
TION described previously.
CLUTCH OPERATING CYLINDER
REMOVAL
NOTE:
Do not allow fluid to get on painted surfaces.
1) Clean around reservoir cap and take out fluid with syringe or
such.
2) Disconnect fluid hose from operating cylinder.
3) Remove operating cylinder attaching bolts and operating cylin-
der.
INSTALLATION
1) For air bleeding of master cylinder alone, it must be removed
from vehicle.
For procedures of removal and installation of master cylinder as-
sembly and air bleeding, refer to CLUTCH MASTER CYLINDER
section.
2) Apply small amount of grease to rod tip.
ªAº: Grease 99000-25010
NOTE:
Don't allow any grease to be on boot.
3) Install clutch operating cylinder and torque attaching bolts to
specification.
4) Connect clutch fluid hose and torque union bolt to specification.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 16.5 lb-ft)
Page 637 of 801
YH4
GRAND
VITARA
BODY SERVICE 9-19
1. Back door panel assy
2. Back door window glass
3. Back door hinge
4. Back door / Rear gate balancer unit
1. Back door hinge
2. Back door
3. Body
BACK DOOR / REAR GATE ASSEMBLY
REMOVAL
1) Remove back door trim, and door / rear gate sealing cover, refer
to steps 1) to 4) of BACK DOOR LOCK ASSEMBLY in this sec-
tion.
2) Remove wire harness connector inside the back door / rear gate.
3) Remove back door / rear gate balancer (first at its door-side and
next at its body-side), as shown.
WARNING:
Handling of Back Door / Rear Gate Balancer (Damper)
Do not disassemble balancer because its cylinder is
filled with gas.
The gas itself is harmless but it may issue out of the
hole together with chips generated by the drill.
Therefore, be sure to wear goggle.
When discarding removed back door / rear gate balanc-
er (damper), use a 2 to 3 mm (0.08 to 0.12 in.) drill to
make a hole as shown.
Handle balancer carefully. Do not scar or scratch ex-
posed surface of its piston rod, and never allow any
paint or oil to stick to its surface.
Do not turn piston rod with balancer fully extended.
5) Remove back door / rear gate hinge bolts and back door / rear
gate.