speed SUZUKI GRAND VITARA 2001 2.G Service Manual Online

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-49
DTC P0751 SHIFT SOLENOID VALVE-A (#1) PERFORMANCE OR STUCK OFF
DTC P0756 SHIFT SOLENOID VALVE-B (#2) PERFORMANCE OR STUCK OFF
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
While running in D range, gear change control from
PCM to A / T does not agree with actual A / T gear posi-
tion even though solenoid valve is electrically in good
condition.
(A / T gear position is calculated based on engine
speed signal and vehicle speed sensor signal.)
(2 driving cycles detection logic)DTC P0751:

Shift solenoid valve-A stuck or leakage.

2-3 shift valve stuck.

Valve body fluid passage clogged.

Mechanical malfunction in transmission.
(Direct clutch malfunction)
DTC P0756:

Shift solenoid valve-B stuck or leakage.

1-2 shift valve stuck.

3-4 shift valve stuck.

Valve body fluid passage clogged.

Mechanical malfunction in transmission.
(2nd brake malfunction)
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF.
2) Clear DTC, pending DTC and freeze frame data in PCM memory by using scan tool and check fuel level meter
indication is 1 / 4 or more.
3) Start engine, warm it up to normal operating temperature and shift transfer lever to ª2Hº or ª4Hº range.
4) Increase vehicle speed with D range, and check that gear position changes from 1st to 2nd, 3rd and 4th in that
order as vehicle speed increases, referring to ªGear Shift Diagramº in this section.
5) Stop vehicle and check pending DTC and DTC by using scan tool.
TROUBLESHOOTING
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Shift solenoid valve-A or -B operation check:
1) Check shift solenoid valve-A or -B for operation
referring to ªSolenoid Valves Operation Checkº
section.
Is it in good condition?Go to Step 3.Faulty shift solenoid
valve-A or -B.
3Valve body check:
1) Check valve body and its passage referring to
ªUnit Repairº section.
Are they in good condition?Overhaul and repair
automatic transmis-
sion.Faulty valve body.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-51
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC.
3) Start engine and shift transfer lever to ª2Hº or ª4Hº range.
4) Shift selector lever in D range and keep it for 10 seconds.
5) Drive vehicle about 30 km / h (20 mph) with 2nd gear in D range for 10 seconds.
6) Increase vehicle speed to about 80 km / h (50 mph) with 4th gear in D range and keep it for 10 seconds.
7) Release accelerator pedal, decrease vehicle speed and stop vehicle.
8) Check DTC and / or pending DTC.
TROUBLESHOOTING (DTC P0753 / P0758)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Is the vehicle equipped with monitor connector?Go to Step 3.Go to Step 4.
3Is DTC NO.61 or 63?Go to Step 4.Go to Step 6.
4Check Shift Solenoid Circuit for Open or Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Check for proper connection to PCM at terminals
C51-1-2 for G16 / J20 (C51-1-6 for H25) or C51-1-1.
3) If OK, then measure resistance between terminal
C51-1-2 for G16 / J20 (C51-1-6 for H25) or C51-1-1
of disconnected PCM connector and ground.
Is it 11 ± 15
at 20C, 68F?Go to Step 5.ªGº or ªG / Rº circuit
open or shorted to
ground.
If wire and
connections are OK,
replace malfunction
shift solenoid.
5Check Shift Solenoid Circuit for Short.
1) Turn ignition switch ON.
2) Measure voltage between terminal C51-1-2 for
G16 / J20 (C51-1-6 for H25) or C51-1-1 of
disconnected PCM connector and ground.
Is it about 0 V?Intermittent trouble or
faulty PCM.
Check for
ªIntermittent and
Poor Connectionº in
Section 0A.ªGº or ªG / Rº circuit
shorted to power
circuit.
6Check Shift Solenoid Circuit for Short.
1) Turn ignition switch OFF and disconnect PCM
connectors.
2) Check for proper connection to PCM at terminals
C51-1-2 for G16 / J20 (C51-1-6 for H25) or C51-1-1.
3) If OK, then measure resistance between terminal
C51-1-2 for G16/J20 (C51-1-6 for H25) or C51-1-1
of disconnected PCM connector and ground.
Is it 11 ± 15
at 20C, 68F?Intermittent trouble or
faulty PCM.
Check for
ªIntermittent and
Poor Connectionº in
Section 0A.ªGº or ªG / Rº circuit
shorted to ground.

YH4
GRAND
VITARA
G16 / J20 Engines
H25 Engine
1. PCM
2. 4WD low switch
3. J / C
7B1-52 AUTOMATIC TRANSMISSION (4 A / T)
DTC P1875 4WD LOW SWITCH CIRCUIT MALFUNCTION (if equipped)
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
While driving at higher than specified vehicle speed
and with more than specified throttle valve opening,
the following conditions are satisfied for specified time.

Vehicle speed sensed by vehicle speed sensor is
more than 10 km / h higher than that sensed by A / T
output speed sensor.
(2 driving cycles detection logic)
4WD LOW switch or its circuit

PCM
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF.
2) Clear DTC, pending DTC and freeze frame data in PCM memory by using scan tool.
3) Start engine.
4) Increase vehicle speed to about 30 km/h (19 mph) or more in D range and is in 2H position.
5) Keep driving at above vehicle speed for 30 seconds.
6) Stop vehicle and shift transfer lever to 4L position with A/T selector lever is in P range
7) Increase vehicle speed to about 25 km/h (15 mph) or more in D range and is in 4L position.
8) Keep driving at above vehicle speed for 30 seconds.
9) Stop vehicle and check pending DTC and DTC by using scan tool.

YH4
GRAND
VITARA
1. Fluid pressure check hole
2. Oil pan
1. Oil pan
2. Exhaust pipe
7B1-54 AUTOMATIC TRANSMISSION (4 A / T)
LINE PRESSURE TEST
Purpose of this test is to check operating conditions of each part by
measuring fluid pressure in fluid pressure line. Line pressure test
requires following conditions.

Automatic fluid is at normal operating temperature (70 to 80C /
158 ± 176F).

Fluid is filled to proper level (between FULL HOT and LOW HOT
on dipstick).
1) Apply parking brake securely and place checks against wheels.
2) Attach oil pressure gauge to fluid pressure check hole in trans-
mission case.
Special Tool
(A): 09925-37810
CAUTION:
After attaching oil pressure gauge, check that not fluid
leakage exists.
3) Depress foot brake fully, run engine at idle and stall and then
check fluid pressure in ªDº or ªRº range.
CAUTION:
Do not continue running engine at stall speed longer than
5 seconds.
G16 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.9 ± 4.4 kg / cm2
55 ± 63 psi
5.1 ± 5.7 kg / cm2
73 ± 81 psi
At stall speed11.7 ± 13.2 kg / cm2
166 ± 188 psi
14.2 ± 16.7 kg / cm2
202 ± 237 psi
J20 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.8 ± 4.3 kg / cm2
54 ± 61 psi
5.3 ± 5.9 kg / cm2
75 ± 84 psi
At stall speed9.7 ± 11.2 kg / cm2
138 ± 159 psi
12.9 ± 15.5 kg / cm2
183 ± 220 psi
H25 Engine
Engine runningLine pressuregg
modeªDº rangeªRº range
At idle speed3.9 ± 4.4 kg / cm2
55 ± 63 psi
6.6 ± 7.2 kg / cm2
94 ± 102 psi
At stall speed11.3 ± 12.7 kg / cm2
161 ± 181 psi
14.7 ± 22.7 kg / cm2
209 ± 323 psi

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-55
Check resultPossible cause
Line pressure higher
than standard level in
each range
Malfunctioning regulator valve

Malfunctioning throttle valve

Maladjusted A / T throttle cable
Line pressure lower than
standard level in each
range
Defective O/D clutch

Defective oil pump

Malfunctioning throttle valve

Malfunctioning regulator value

Maladjusted A / T throttle cable
Line pressure lower than
standard level only in ªDº
range
Fluid leakage from forward clutch

Defective O/D clutch

Leakage from ªDº range fluid pressure cir-
cuit
Line pressure lower than
standard level only in ªRº
range
Fluid leakage from direct clutch

Defective O/D clutch

Fluid leakage from reverse brake

Fluid leakage from ªRº range fluid circuit
Tightening torque of transmission case plug:
17 N.m (1.7 kg-m, 12.0 lb-ft)
STALL TEST
This test is to check overall performance of automatic transmission
and engine by measuring stall speed at ªDº and ªRº ranges. Be sure
to perform this test only when transmission fluid is at normal operat-
ing temperature and its level is between FULL and LOW marks.
CAUTION:

Do not run engine at stall more than 5 seconds continu-
ously, for fluid temperature may rise excessively high.

After performing stall test, be sure to leave engine running
at idle for longer than 30 seconds before another stall test.
1) Apply parking brake and block wheels.
2) Install tachometer.
3) Start engine with select lever shifted to ªPº.
4) Depress brake pedal fully.
5) Shift select lever to ªDº and depress accelerator pedal fully while
watching tachometer. Read engine rpm quickly when it has be-
come constant (stall speed).
6) Release accelerator pedal immediately after stall speed is
checked.
7) In the same way, check stall speed in ªRº range.

YH4
GRAND
VITARA
7B1-56 AUTOMATIC TRANSMISSION (4 A / T)
8) Stall speed should be within the following specification.
Stall speed: 2,100 ± 2,400 r / min. for G16 engine
2,300 ± 2,600 r / min. for J20 engine
2,300 ± 2,600 r / min. for H25 engine
Check result
Possible cause
Lower than standard
level
Faulty engine output

Defective torque converter
Higher than standard
level in ªDº range
Slippery O/D clutch

Slippery forward clutch

Malfunctioning O/D one-way clutch

Malfunctioning one-way clutch No. 2

Low line pressure
Higher than standard
level in ªRº range
Slippery direct clutch

Slippery reverse brake

Low fluid pressure

Slippery O/D clutch

Defective O/D one-way clutch
ROAD TEST
This test is to check if upshift and downshift take place at specified
speed while actually driving vehicle on a level road.
WARNING:

Carry out test in very little traffic area to prevent an acci-
dent.

Test requires 2 persons, a driver and a tester.
1) Warm up engine.
2) With engine running at idle, shift select lever ªDº.
3) Accelerate vehicle speed by depressing accelerator pedal grad-
ually.
4) While driving in ªDº range, check if gear shift occurs properly as
shown in Gear Shift Diagram in this section.
Test result
Possible cause
When 1
2 upshift fails to
occur1±2 shift valve stuck
When 2
3 upshift fails to
occur2±3 shift valve stuck
When 3
O/D upshift
fails to occur3±4 shift valve stuck
When gear shift point is in-
correct
Maladjusted throttle cable

Defective shift solenoid valve
-A or -B

1±2, 2±3 or 3±4 shift valve not
operating properly

YH4
GRAND
VITARA
1
1. Shift solenoids connector
AUTOMATIC TRANSMISSION (4 A / T) 7B1-57
MANUAL ROAD TEST
This test check the gear being used in ªLº, ª2º or ªDº range when
driven with unoperated gear shift control system. Test drive vehicle
on a level road.
NOTE:
Before this test, check diagnostic trouble code (DTC).
1) Disconnect coupler of shift solenoid valves on transmission.
WARNING:
To avoid the danger of being burned, do not touch the hot
exhaust system when disconnecting shift solenoid
valves coupler.
2) With select lever in ªPº, start engine and warm it up.
3) With select lever in ªLº range, start vehicle and accelerate to 20
km/h (12.5 mile/h). Check in this state that 1st gear is being
used.
4) At 20 km/h (12.5 mile/h), shift select lever to 2 range and acceler-
ate to 40 km/h (25 mile/h). Check in this state that 3rd gear is
being used.
5) At 40 km/h (25 mile/h), shift select lever to D range and check
that O/D gear is used when speed is higher than 40 km/h (25
mile/h).
6) After above checks, stop vehicle then engine, and connect shift
solenoids coupler with ignition switch OFF.
WARNING:
To avoid the danger of being burned, do not touch the hot
exhaust system when connecting shift solenoid valves
coupler.
7) Clear DTC with scan tool.
TIME LAG TEST
This test is to check conditions of clutch, reverse brake and fluid
pressure. ªTime lagº means time elapsed since select lever is
shifted with engine idling till shock is felt.
1) With chocks placed before and behind front and rear wheels re-
spectively, depress brake pedal.
2) Start engine.
3) With stop watch ready, shift select lever from ªNº to ªDº range
and measure time from that moment till shock is felt.
4) Similarly measure time lag by shifting select lever from ªNº to ªRº
range.
Specification for ªNº
ªDºLess than 1.2 sec.
time lagªNº
ªRºLess than 1.5 sec.
NOTE:

When repeating this test, be sure to wait at least minute
after select lever is shifted back to ªNº range.

Engine should be warmed up fully for this test.
Test resultPossible causes
When ªNº
ªDº time lag
exceeds specification
Low line pressure

Worn forward clutch
When ªNº
ªRº time lag
exceeds specification
Low line pressure

Worn direct clutch

Worn reverse brake

YH4
GRAND
VITARA
7B1-64 AUTOMATIC TRANSMISSION (4 A / T)
1. A / T vehicle (output) speed sensor
ªNº reference
line
Center line on
manual valve shaft
G16 / J20
1. Service wire
2. PCM connectors disconnected
Switch
position
TRANSMISSION RANGE SWITCH (SENSOR)
INSPECTION & ADJUSTMENT
1) Shift select lever to ªNº range.
2) Check that center line on manual valve shaft and ªNº reference
line on switch are aligned. If not, loosen switch bolt and align
them.
3) Check that engine starts in ªNº and ªPº ranges but it doesn't start
in ªDº, ª2º, ªLº or ªRº range. Also, check that back-up lamp lights
in ªRº range.
4) If faulty condition cannot be corrected by adjustment, discon-
nect transmission range switch coupler and check that continu-
ity exists as shown by moving select lever.
Terminal No.54982310765498231076
P
R
N
D
2
L
A / T OUTPUT SPEED SENSOR
INSPECTION
Check A / T output speed sensor for resistance between terminals
of sensor or PCM coupler.
A / T output speed sensor
resistance value : 387 ± 473
at 20
C, 68
F
O / D CUT SWITCH
INSPECTION
Check O / D cut switch for operation referring to step 4 of Diag. Flow
Table B-2 in this section.
If malfunction is found, replace.
SOLENOID VALVES
(Shift solenoid valves & TCC solenoid valve)
INSPECTION
With couplers of PCM disconnected and using service wire as
shown at the left, check each solenoid valve for clicking sound.
G16 / J20 Engines
Shift solenoid valve - A (#1)C51-1-2
Shift solenoid valve - B (#2)C51-1-1
TCC (Lock-up) solenoid valveC51-1-8

YH4
GRAND
VITARA
7B1-76 AUTOMATIC TRANSMISSION (4 A / T)
12) Remove engine to transmission nuts.
13) Disconnect connectors from VSS, output speed sensor, input
speed sensor, TR switch, shift & TCC solenoid valves and oth-
er electrical parts, and release their wire harness from clamps.
14) Apply transmission jack and take off rear mounting member by
removing its bolts.
15) With transmission (and transfer if equipped) assembly held up
on jack, move them to the rear and lower them including torque
converter.
WARNING:
Transmission (and transfer if equipped) assembly may
tilt rearward on jack. It is recommended to use an auxil-
iary arm of jack for the purpose of safety.
AFTER DISMOUNTING
WARNING:
Be sure to keep transmission (and transfer if equipped) as-
sembly horizontal throughout the work. Should they be
tilted, torque converter may fall off and cause personal inju-
ry and A / T fluid may flow out.
1) Remove breather hoses.
2) Remove transfer by removing its bolts, if equipped.

YH4
GRAND
VITARA
7D
TRANSFER 7D-1
The aluminum transfer case directly connected to the
back of the transmission contains the input gear,
countershaft & gear, output rear shaft, output low gear
and output front shaft (for front drive) connected by
way of the hyvo-chain.
The transfer has such a selective mechanism as to
enable the shift control lever to make selection of high
speed (direct connection with transmission output:
main shaft), low speed (speed reduction by input
gear, counter gear and output low gear) or neutral by
way of the reduction sleeve located between input
gear and output low gear, and selection of two-wheel-
drive (high speed only) or four-wheel-drive (high or
low speed) by way of the front drive clutch sleeve lo-cated at the center of the output rear shaft. Also, with
a synchronizer installed to the front drive clutch, it is
possible to change the drive mode between 2WD
(high speed only) and 4WD (high speed only) even
while running.
The front drive shift fork has an auxiliary spring to
make a smooth shift from 4H to 2H possible.
The case has an oil gutter and a plate at synchronizer
to provide proper lubrication even under the strict
conditions of use.
WARNING:
For towing the vehicle for the purpose of repair or
the like, follow the towing instructions in OWN-
ER'S MANUAL.
SECTION 7D
TRANSFER
CONTENTS
GENERAL DESCRIPTION7D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Oil Seals7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer Driven Gear7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Assembly7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismounting7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remounting7D-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION