Assembly SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA
6
5
1. Headlight assembly
2. Halogen bulb
3. Socket cover
4. Turn signal light bulb
5. Position light bulb
6. Turn signal light bulb socket
7. Position light bulb socket
8B-2 LIGHTING SYSTEM
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
HEADLIGHTS

YH4
GRAND
VITARA
Terminal
Wire ColorSwitch Position
Terminal
Switch Position
Wire Color
HEAD
OFFHI
PASS SMALL
8B-6 LIGHTING SYSTEM
ON-VEHICLE SERVICE
HEADLIGHTS
HEADLIGHT SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
Lighting Switch
ELTH
WGR
OFF
SMALL
HEAD
Dimmer & Passing Switch
EDHLHUHF
W/BR/WRR/B
Passing (PASS)
Low Beam
High Beam (HI)
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
REMOVAL
1) Disconnect negative cable at battery.
2) Remove front grille.
3) Disconnect harness and couplers from headlight assembly.
4) Remove three bolts and pull headlight assembly off vehicle.
INSTALLATION
Reverse removal procedure for installation.
Make sure to follow HEADLIGHT AIMING WITH SCREEN and aim
headlight after installation.

YH4
GRAND
VITARA
8B-8 LIGHTING SYSTEM
HEADLIGHTS WITH LEVELING SYSTEM
(IF EQUIPPED)
LEVELING SWITCH
INSPECTION
To check the switch operation, substitute it with a new one. If proper
operation is obtained, it means the switch is defective.
Replace it with a new one.
LEVELING ACTUATOR
INSPECTION
All headlight system couples connected including leveling actuator
and switch, and at Ignition switch ON, listen to the leveling actuator
sound on both actuators according to the movement of the leveling
switch. If no sound is heard with the movement of the leveling
switch, replace headlight assembly.

YH4
GRAND
VITARA
1. Meter cluster
2. Hazard switch
Terminal
Wire ColorSwitch Position
LH steering vehicle shown
LIGHTING SYSTEM 8B-9
TURN SIGNAL AND HAZARD WARNING
LIGHTS
TURN SIGNAL SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
TLTBTR
G/RGG/Y
L
N
R
REMOVAL AND INSTALLATION
Refer to Section 3C COMBINATION SWITCH for vehicle without air
bag system and Section 3C1 CONTACT COIL AND COMBINA-
TION SWITCH ASSEMBLY for vehicle with air bag system.
HAZARD SWITCH
REMOVAL
1) Remove meter cluster.
2) Pull hazard switch out of instrument panel.
3) Disconnect coupler from hazard switch.
4) Remove hazard switch.
INSTALLATION
Reverse removal procedure.
INSPECTION
Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace siwtch.

YH4
GRAND
VITARA
8C-6 INSTRUMENTATION / DRIVER INFORMATION
KeyPosition
TerminalWire
color
Hard Top Model
Canvas Top Model
ON-VEHICLE SERVICE
IGNITION (MAIN) SWITCH
INSPECTION
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Disconnect main switch lead wire coupler.
4) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace ignition
(main) switch.
+B+ACCIG1-1IG1-2IG2STL1L2K1K2
W/YBlB/WB/WY/BB/YBBGG
OUTLOCKLOCK
ACC
IN
ON
START
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Remove steering column referring to Section 3C1 of this manu-
al. Then remove steering lock / ignition (main) switch from steer-
ing column.
INSTALLATION
1) Install steering lock / ignition (main) switch to steering column.
Install steering column assembly referring to Section 3C1 of this
manual.
2) Enable air bag system. Refer to ENABLING AIR BAG SYSTEM
in Section 10B of this manual.
NOTE:
When installing steering column, special care must be tak-
en for tightening sequence and its torque.

YH4
GRAND
VITARA
INSTRUMENTATION / DRIVER INFORMATION 8C-9
1. Exhaust pipe
FUEL METER / FUEL GAUGE UNIT
FUEL METER
INSPECTION
1) Remove rear bumper facing.
2) Detach grommet (3) from vehicle.
3) Disconnect coupler (2) of fuel pump and gauge.
4) Turning switch ON, and check that fuel meter indicates E.
5) Turn ignition switch OFF.
6) Ground Bl / W lead through a 3.4 W test bulb (4) as illustrated.
7) Turn ignition switch ON and check that bulb light up and pointer
(5) moves to F side.
8) If fuel meter shows no operation, repair or replace defective
parts.
FUEL SENDER GAUGE
INSPECTION
1) Remove fuel pump assembly (1) referring to FUEL PUMP RE-
MOVAL in Section 6C.
2) Check resistance between terminals (A) and (B) under each
float position.
Float Position
FuelResistance (
)56
model66
modelMeterResistance (
)
ªaº88.3 mm
(3.48 in.)51.7 mm
(2.04 in.)F6 ± 8
ªbº157.2 mm
(6.20 in.)139.6 mm
(5.50 in.)1/229.5 ± 35.5
ªcº254.9 mm
(10.0 in.)254.9 mm
(10.0 in.)E94 ± 96
If measured valve is out of specification, replace fuel sender gauge.

YH4
GRAND
VITARA
Front Wiper Assembly
Washer AssemblyFront Wiper Switch
8D-2 WINDOWS, MIRRORS, SECURITY AND LOCKS
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER

YH4
GRAND
VITARA
Rear Wiper Switch
Rear Wiper Intermittent Relay Rear Wiper Assembly
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-3
REAR WIPER AND WASHER (IF EQUIPPED)

YH4
GRAND
VITARA
WASHER
ONINT
LO
HI
Type A
Type B
Type C
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-9
Wiper
SW
Terminal
Wiper SW
Terminal
ON-VEHICLE SERVICE
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER
INSPECTION
Front Wiper and Washer Switch (in Combination Switch)
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
B3+2+1AsB3+2+1As
OFFB3WINTB3W
LOOFF
HION
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
Wiper Motor
1) As illustrated, use a 12 V battery to connect its (+) terminal to ter-
minal ªAº, and its (±) terminal to Black lead wire (2) (Type A, B)
or terminal ªEº (Type C).
If motor (1) rotates at a low revolution speed of 45 to 55 rpm, it
is proper. For high speed check, connect battery (+) terminal to
terminal ªBº, and its (±) terminal to Black lead wire (2) (Type A,
B) or terminal ªEº (Type C). If motor rotates at a high revolution
speed of 67 to 83 rpm, it is proper.

YH4
GRAND
VITARA
Terminal
Operation
If mirror heater is not equipped
If mirror heater is equipped
8D-30 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR MIRROR CONTROL SYSTEM
INSPECTION
MIRROR SWITCH
1) Remove mirror switch from instrument panel.
2) Check for continuity between terminals at each switch position
as shown below.
If check result is not as specified, replace mirror switch.
DOOR MIRROR ACTUATOR
1) Remove garnish from door.
2) Disconnect door mirror coupler.
3) Check that door mirror operates properly when battery voltage
is applied to connector terminals.
Connect battery positive and negative terminal to the door mirror
terminal shown below and check operation.
If it does not operate as specified in table below, replace door
mirror assembly.
VBlYVBlY
Up

Down

Left

Right

NOTE:
When installing door mirror to door, be careful not to pinch
harness between door and door mirror.