rear axle bearing SUZUKI GRAND VITARA 2002 2.G Service User Guide

YH4
GRAND
VITARA
REAR SUSPENSION 3E-23
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mKg-mlb-ft
Shock absorber lock nut292.921.0
Shock absorber nut292.921.0
Shock absorber lower nut858.561.5
Lower rod bolt and nut
Upper rod bolt and nut909.065.0
Lateral rod bolt
Differential carrier nut555.540.0
Propeller shaft nut505.036.5
Brake pipe flare nut161.611.5
Bearing retainer nut232.317.0
Differentiation gear oilFiller plug505.036.5g
filler & drain plugDrain plug272.716.0
Wheel nut10010.072.5
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUZUKI SUPER GREASE A
(99000-25010)Oil seal lip
Brake fluidDOT 3Brake reservoir tank
Sealant
SUZUKI BOND NO. 1215
(99000-31110)
Joint seam of axle and brake back
plate

Joint seam of bearing retainer and
brake back plate

Joint seam of differential carrier and
axle housing

Drain plug

Mating surface of oil seal and axle
housing
Gear oilFor gear oil information, refer to
SECTION 7F of this manualDifferential gear
(Refer axle housing.)

YH4
GRAND
VITARA
BRAKES 5-5
ConditionPossible CauseCorrection
Excessive pedal
travel (Pedal
stroke too large)
Partial brake system failure.

Insufficient fluid in master cylinder
reservoirs.

Air in system. (pedal soft / spongy)

Rear brake system not adjusted.
(malfunctioning auto adjusting mechanism)

Bent brake shoes.

Worn rear brake shoes.Check brake systems and repair as
necessary.
Fill reservoirs with approved brake
fluid.
Check for leaks and air in brake
systems.
Check warning light. Bleed system if
required.
Bleed system.
Repair auto adjusting mechanism.
Adjust rear brakes.
Replace brake shoes.
Replace brake shoes.
Dragging brakes
(A very light drag
is present in all
disc brakes
immediately
after pedal is
released)
Master cylinder pistons not returning
correctly.

Restricted brake pipes or hoses.

Incorrect parking brake adjustment on rear
brakes.

Weakened or broken return springs in the
brake.

Sluggish parking-brake cables or linkage.

Wheel cylinder or caliper piston sticking.

Malfunctioning ABS, if equipped with ABS.Replace master cylinder.
Check for soft hoses or damaged
pipes and replace with new hoses
and / or new brake pipes.
Check and adjust to correct specifi-
cations.
Replace.
Repair or replace.
Repair as necessary.
Check system and replace as
necessary.
Pedal pulsation
(Pedal pulsates
when depressed
for braking)
Damaged or loose wheel bearings.

Distorted steering knuckle or rear axle
shafts.

Excessive disc lateral runout.

Parallelism not within specifications.

Rear drums out of round.Replace wheel hub component.
Replace knuckle or rear axle shaft.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check per instructions. If not within
specifications, replace or machine
the disc.
Check runout.
Repair or replace drum as
necessary.
Braking noise
Glazed shoe linings, or foreign matters
stuck to linings.

Worn or distorted shoe linings.

Loose front wheel bearings.

Distorted backing plates or loose mounting
bolts.Repair or replace shoe lining.
Replace shoe lining (or pad).
Replace wheel hub component.
Replace or retighten securing bolts.

YH4
GRAND
VITARA
5C-14 PARKING AND REAR BRAKE
1
2
3
1. Brake back plate
2. Cable cap
3. Brake cable
1. Wheel bearing retainer nut
1. Rear axle shaft
2. Wheel bearing
3. Brake back plate(A)
BRAKE BACK PLATE
REMOVAL
1) Perform steps 1) to 5) of BRAKE DRUM REMOVAL.
2) Perform steps 2) to 4) of BRAKE SHOE REMOVAL.
3) Perform steps 3) and 4) of WHEEL CYLINDER REMOVAL.
4) Remove cable from brake back plate by squeezing parking
brake cable cap.
5) Drain rear differential gear oil.
6) Remove wheel bearing retainer nuts from rear axle housing.
7) Using special tools, draw out rear axle shaft with brake back
plate.
Special Tool
(A): 09943-35512
(B): 09942-15510
8) Remove brake back plate from rear axle shaft.

YH4
GRAND
VITARA
PARKING AND REAR BRAKE 5C-15
1. Rear axle shaft
2. Wheel bearing
3. Brake back plate1. Rear axle shaft
1. Rear axle
housing ªAº
INSTALLATION
1) Apply sealant to mating surface of bearing retainer with brake
back plate.
ªAº: Sealant 99000-31110
NOTE:
Make sure to remove old sealant before applying it anew.
2) Install brake back plate to rear axle shaft.
3) Apply sealant to joint seam of rear axle housing and brake back
plate.
ªAº: Sealant 99000-31110
NOTE:
Make sure to remove old sealant before applying it anew.
4) Install rear axle shaft to rear axle housing.
5) Tighten brake back plate nuts to specified torque.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
PARKING AND REAR BRAKE 5C-17
09943-35512
Brake drum remover
(Front wheel hub remover)09942-15510
Sliding hammer
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Wheel cylinder bleeder plug7.50.755.5
Parking brake lever bolt232.317.0
Wheel cylinder bolt (For non sealed type)8.50.856.5
Wheel cylinder bolt (For gasket sealed type)111.112.0
Brake pipe flare nut161.612.0
Brake back plate nut232.317.0
Wheel nut10010.072.5
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.
Water tight
sealantSEALING COMPOUND 366E
99000-31090
To apply to mating surfaces of brake back
plate and rear wheel cylinder.
SealantSUZUKI BOND NO. 1215
99000-31110

To apply to mating surfaces of brake back
plate and rear axle housing.

To apply mating surfaces of brake back
plate and rear wheel bearing retainer.
SPECIAL TOOLS

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-39
1. Rear axle
2. Retainer ring
3. Sensor rotor
4. Vinyl envelope
ªAº Grind with grinderªAº
1. Sensor rotor 4
31
2
2 1
3
REAR SENSOR ROTOR
REMOVAL
1) Remove rear axle shaft. Refer to REAR AXLE SHAFT RE-
MOVAL in Section 3E.
2) In order to remove sensor rotor from retainer ring, grind with a
grinder one part of the sensor rotor as illustrated till it becomes
thin.
CAUTION:

Cover vinyl sheet or the like over wheel bearing so that
fine grains from grinding will not enter there.

Be careful not to go so far as to grind the retainer ring.
3) Break with a chisel the thin ground sensor rotor, and it can be re-
moved.
INSTALLATION
1) Press-fit sensor rotor as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
2) Install rear axle shaft. Refer to REAR AXLE SHAFT INSTALLA-
TION in Section 3E.

YH4
GRAND
VITARA
7F-2 DIFFERENTIAL (REAR)
DIAGNOSIS
ConditionPossible CauseCorrection
Gear noise
Deteriorated or water mixed lubricant

Inadequate or insufficient lubricant

Maladjusted backlash between bevel
pinion and gear

Improper tooth contact in the mesh between
bevel pinion and gear

Loose bevel gear securing bolts

Damaged side gear(s) or side pinion(s)Repair and replenish
Repair and replenish
Adjust as prescribed
Adjust or replace
Replace or retighten
Replace
Bearing noise
(Constant noise) Deteriorated or water
mixed lubricant

(Constant noise) Inadequate or insufficient
lubricant

(Noise while coasting) Damaged bearing(s)
of bevel pinion

(Noise while turning) Damaged diff. side
bearing(s) or axle bearing(s)Repair and replenish
Repair and replenish
Replace
Replace
Oil leakage
Clogged breather plug

Worn or damaged oil seal

Excessive oilClean
Replace
Adjust oil level