SUZUKI GRAND VITARA 2002 2.G Service Workshop Manual

YH4
GRAND
VITARA
1
1. Lugs
2. Grooves
3. Alignment marks
2. Steering column upper cover
3. Steering column lower cover 1. Steering column
cover screw
(a)
1. Steering column hole cover
AIR BAG STEERING WHEEL AND COLUMN 3C1-7
INSTALLATION
1) Check that vehicle's front tires are at straight-ahead position and
contact coil is centered. Refer to ªCENTERING CONTACT
COILº in this section.
CAUTION:
These two conditions are prerequisite for installation of
steering wheel. If steering wheel has been installed with-
out these conditions, contact coil will break when steer-
ing wheel is turned.
2) Install steering wheel to steering shaft with 2 lugs on contact coil
fitted in two grooves in the back of steering wheel and also align-
ing marks on steering wheel and steering shaft.
3) Tighten steering shaft nut to specified torque.
Tightening Torque
(a): 33 N
.m (3.3 kg-m, 23.5 lb-ft)
4) Install driver air bag (inflator) module to steering wheel. Refer to
ªDRIVER AIR BAG (INFLATOR) MODULEº in this section.
CONTACT COIL AND COMBINATION SWITCH
ASSEMBLY
CAUTION:
Do not turn contact coil (on combination switch) more than
allowable number of turns (about two and a half turns from
the center position clockwise or counterclockwise respec-
tively), or coil will break.
REMOVAL
1) Remove steering wheel from steering column. Refer to
ªSTEERING WHEELº in this section.
2) Remove steering column hole cover.
3) Remove steering column cover screws (3 pieces).
4) Separate upper cover and lower cover, then remove them.
5) Disconnect all connectors for contact coil and combination
switch assembly.

YH4
GRAND
VITARA
1
1. Contact coil and combination switch assembly
2. Screw
1. Contact coil and combination switch assembly
1. Seal (if equipped, remove lock pin after installing
contact coil and combination switch assembly.)
2. Lock pin (if equipped, remove lock pin after installing
contact coil and combination switch assembly.)
3C1-8 AIR BAG STEERING WHEEL AND COLUMN
6) Remove contact coil and combination switch assembly from
steering column.
INSPECTION
Check contact coil and combination switch wire harness for any
signs of scorching, melting or other damage. If it is damaged, re-
place.
INSTALLATION
1) Check to make sure that vehicle's front tires are set at straight-
ahead position and then ignition switch is at ªLOCKº position.
2) Install contact coil and combination switch assembly to steering
column.
NOTE:
New contact coil and combination switch assembly is sup-
plied with contact coil set and held at its center position
with a lock pin and seal. Remove this lock pin after installing
contact coil and combination switch assembly to steering
column.

YH4
GRAND
VITARA
1
1. Steering column hole cover 1. Steering column cover screw
2. Steering column upper cover
3. Steering column lower cover: Standard screw
: Tapping screw
*
* *
AIR BAG STEERING WHEEL AND COLUMN 3C1-9
3) Connect all connectors that have been removed in removal.
4) Install steering column upper and lower cover, and then tighten
steering column cover screws.
CAUTION:
When installing lower cover and upper cover, be careful
so that contact coil and combination switch lead wire is
not caught between covers.
5) Install steering column hole cover.
6) Install steering wheel to steering column. Refer to ªSTEERING
WHEELº in this section.
STEERING COLUMN
CAUTION:
Once the steering column is removed from the vehicle, the
column is extremely susceptible to damage.
Dropping the column assembly on its end could collapse
the steering shaft or loosen the plastic shear pins which
maintain column length leaning on the column assembly
could cause it to bend or deform.
Any of the above damage could impair the column's col-
lapsible design.
When loosening steering column mounting bolts, make
sure that steering column assembly and steering shaft low-
er assembly have been separated. Loosening them with
steering column assembly and steering shaft lower assem-
bly assembled could cause damage to bearing in steering
shaft lower assembly.
NOTE:
When servicing steering column or any column-mounted
component, remove steering wheel. But when removing steer-
ing column simply to gain access to instrument panel compo-
nents, leave steering wheel installed on steering column.

YH4
GRAND
VITARA
1. Steering column assembly
2. Steering shaft joint
3. Marks
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)1. Steering column hole cover
1
3C1-10 AIR BAG STEERING WHEEL AND COLUMN
REMOVAL
WARNING:
Never rest a steering column assembly on the steering
wheel with air bag (inflator) module face down and column
vertical. Otherwise personal injury may result.
1) Disconnect negative battery cable at battery terminal.
2) Disable air bag system. Refer to ªDISABLING AIR BAG SYS-
TEMº under ªSERVICE PRECAUTIONSº in Section 10B.
3) Remove steering wheel and contact coil and combination switch
assembly, if necessary. Refer to ªSTEERING WHEELº and
ªCONTACT COIL AND COMBINATION SWITCH ASSEMBLYº
in this section.
Perform the following procedure if not removing steering wheel
and/or combination switch.
ii) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
ii) Turn ignition switch to ªLOCKº position and remove key.
4) Remove steering column hole cover.
5) Disconnect all connectors for the following parts.

Contact coil and combination switch

Ignition switch
6) Make alignment marks on shaft joint and shaft (column side) for
a guide during reinstallation.
7) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in the figure).

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-11
1. Steering column
2. Steering column mounting bolt
3. Steering column lower seal
1. Shift (key) interlock cable
2. Screw
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly ªaº
8) Remove steering column mounting bolts (6 pieces).
9) If equipped with shift (key) interlock cable, remove shift (key)
interlock cable screw and then disconnect its cable from igni-
tion switch.
10) Remove steering column from vehicle.
INSPECTION
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted or air bag
deployed, may have a damaged or misaligned steering col-
umn.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)

YH4
GRAND
VITARA
1. Steering column
2. Mounting bolt
3. Steering column lower seal
4. Dash panel
1. Steering column lower seal
In engine room
In cabin
1. Shift (key) interlock cable
2. Screw
3C1-12 AIR BAG STEERING WHEEL AND COLUMN
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering lower shaft assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.
INSTALLATION
CAUTION:
After tightening steering column mounting bolts, steering
shaft joint bolts should be tightened.
1) Be sure that front wheels and steering wheel are in straight-
ahead position.
2) If equipped with shift (key) interlock cable, install shift (key) inter-
lock cable to ignition switch.
Tightening Torque
(a): 2.2 N
.m (0.22 kg-m, 1.6 lb-ft)
3) Install steering column assembly to dash panel and upper
bracket so that boss of steering column lower seal and all around
it project out of hole in dash panel into engine room. Tighten
steering column lower bolts (4 pieces) first and then upper bolts
(2 pieces) to specified torque.
Tightening Torque
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
1. Steering shaft joint
2. Steering shaft (column side)
3. Marks
1. Steering shaft joint
2. Bolt (column side)
3. Bolt (lower shaft assembly side)
1. Steering column hole cover
1
AIR BAG STEERING WHEEL AND COLUMN 3C1-13
4) Install steering shaft joint to steering shaft by matching it to
marks made before removal.
5) Install shaft joint bolt (column side) to steering shaft joint. Tighten
shaft joint bolt (column side) to specified torque first and then
shaft joint bolt (lower shaft assembly side) to specified torque.
Tightening Torque
(c): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
6) If contact coil and combination switch assembly is removed,
install it, referring to ªCONTACT COIL AND COMBINATION
SWITCH ASSEMBLYº in this section.
7) Connect all connectors that have been removed in removal.
8) Install steering column hole cover.
9) If steering wheel is removed, install it by referring to ªSTEER-
ING WHEELº in this section.
10) Connect negative battery cable.
11) After installing steering column assembly, be sure to enable air
bag system by referring to ªENABLING AIR BAG SYSTEMº un-
der ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
3C1-14 AIR BAG STEERING WHEEL AND COLUMN
1. Steering column
2. Steering lock 1
2
1. Center punch (with sharp point)
2. Steering lock mounting bolt
1. Steering column
2. Steering shaft
STEERING LOCK ASSEMBLY (IGNITION
SWITCH)
REMOVAL
1) Remove steering column. Refer to ªSTEERING COLUMNº in
this section.
2) Using center punch as shown, loosen and remove steering lock
mounting bolts.
NOTE:
Use care not to damage aluminum part of steering lock
body with center punch.
3) Turn ignition key to ªACCº or ªONº position and remove steering
lock assembly from steering column.
INSTALLATION
1) Position oblong hole of steering shaft in the center of hole in col-
umn.
2) Turn ignition key to ªACCº or ªONº position and install steering
lock assembly onto column.
3) Now turn ignition key to ªLOCKº position and pull it out.
4) Align hub on lock with oblong hole of steering shaft and rotate
shaft to assure that steering shaft is locked.
5) Tighten new bolts until head of each bolt is broken off.
6) Turn ignition key to ªACCº or ªONº position and check to be sure
that steering shaft rotates smoothly. Also check for lock opera-
tion.
7) Install steering column. Refer to ªSTEERING COLUMNº in this
section.

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-15
1. Steering column assembly
2. Steering shaft joint
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)
1. Steering lower shaft assembly
2. Steering lower shaft assembly
lower joint bolt
3. Steering shaft joint
STEERING LOWER SHAFT ASSEMBLY
CAUTION:
Never turn steering wheel while steering lower shaft assem-
bly is removed.
Should it have been turned and contact coil (on combina-
tion switch) have got out of its centered position, it needs
to be centered again. Also, turning steering wheel more
than about two and a half turns will break contact coil.
REMOVAL
1) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
2) Turn ignition switch to ªLOCKº position and remove key.
3) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in figure).
4) Remove lower shaft assembly lower joint bolt and then remove
lower shaft assembly.
5) Remove shaft joint bolt (lower shaft assembly side) from shaft
joint and then remove shaft joint from lower shaft assembly.

YH4
GRAND
VITARA
2
1
1. Steering shaft joint
2. Bolt (Steering column assembly side)
3. Bolt (Steering lower shaft assembly side)1. Steering shaft joint
2. Steering lower shaft assembly
1. Steering lower shaft
assembly
2. Steering lower shaft
assembly lower joint
3. Steering lower shaft
assembly lower joint bolt
4. Steering shaft joint
5. Mark
6. Slit
1. Steering column assembly
2. Steering shaft joint
3C1-16 AIR BAG STEERING WHEEL AND COLUMN
INSTALLATION
1) Be sure that front wheels and steering wheel are in straight
ahead position.
2) Align flat part ªAº of lower shaft assembly with bolt hole ªBº of
shaft joint as shown. Then insert shaft joint into lower shaft as-
sembly.
3) Install shaft joint bolt (lower shaft assembly side) to shaft joint.
Then tighten it by hand.
4) Insert pinion shaft into lower shaft assembly lower joint with slit
of lower joint, marks on pinion shaft and gear case aligned.
And then install lower shaft assembly lower joint bolt to lower
shaft assembly lower joint. Tighten it to specified torque.
Tightening Torque
(a): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
5) Install steering shaft joint to steering shaft.
NOTE:
Be sue that front wheels and steering wheel are in straight-
ahead position.
6) Install shaft joint bolt (column side) to shaft joint. Tighten shaft
joint bolt (column side) to specified torque first and then shaft
joint bolt (shaft lower assembly side) to specified torque.
Tightening Torque
(b): 25 N
.m (2.5 kg-m, 18.0 lb-ft)