3c1 SUZUKI GRAND VITARA 2002 2.G Service Owner's Manual

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-17
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly
1. Steering column lower seal ªaº
CHECKING STEERING COLUMN FOR
ACCIDENT DAMAGE
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted or air bag
deployed, may have a damaged or misaligned steering col-
umn.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering shaft lower assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.

YH4
GRAND
VITARA
1. Lower position
2. Upper position
3C1-18 AIR BAG STEERING WHEEL AND COLUMN
09944-36011
Steering wheel remover
ADJUSTABLE STEERING COLUMN RELEASE
LEVER
INSPECTION
Check to make sure that the following:

Steering column moves smoothly when adjustable steering col-
umn release lever is at lower position (i.e., steering column is not
locked).

Steering column is fixed securely when adjustable steering col-
umn release lever is at upper position (i.e., steering column is
locked).
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Driver air bag (inflator) module bolt90.96.5
Steering shaft nut333.323.5
Steering column mounting bolt232.317.0
Steering shaft joint bolt252.518.0
Steering lower shaft assembly lower joint bolt252.518.0
Shift (key) interlock cable screw2.20.221.6
SPECIAL TOOL

YH4
GRAND
VITARA
5E1-14 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
DIAGNOSTIC TROUBLE CODE (DTC) TABLE
DTC
(indicated
DTC
(displayedVOLTMETER INDICATION(indicated
by ABS
i
(dis layed
on
SUZUKI
VOLTMETER INDICATION
(or ªABSº warning
lflhi tt)
DIAGNOSTIC AREA
warning
lamp)SUZUKI
scan tool)
lamp flashing pattern)
15C1015G sensor (for 4WD model only)
21C1021Right-21C1021g
front
25C1025Left-25C1025front
31C1031Right-31C1031g
rear
35C1035Left-35C1035rearWheel speed sensor circuit and rotor
22C1022Right-Wheel speed sensor circuit and rotor
22C1022g
front
26C1026Left-26C1026front
32C1032Right-32C1032g
rear
36C1036Left-36C1036rear
41C1041Right-Inlet solenoid circuit41C1042
g
frontOutlet solenoid circuit
45C1045Left-Inlet solenoid circuit45C1046frontOutlet solenoid circuit
56C1055RearInlet solenoid circuit56C1056RearOutlet solenoid circuit
57C1057Solenoid and pump motor power source circuit
61C1061ABS pump motor (in hydraulic unit) circuit
63C1063ABS fail-safe relay circuit
71C1071ABS control moduleInternal malfunction
12±Normal

YH4
GRAND
VITARA
Terminal
Wire ColorSwitch Position
Terminal
Switch Position
Wire Color
HEAD
OFFHI
PASS SMALL
8B-6 LIGHTING SYSTEM
ON-VEHICLE SERVICE
HEADLIGHTS
HEADLIGHT SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
Lighting Switch
ELTH
WGR
OFF
SMALL
HEAD
Dimmer & Passing Switch
EDHLHUHF
W/BR/WRR/B
Passing (PASS)
Low Beam
High Beam (HI)
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
REMOVAL
1) Disconnect negative cable at battery.
2) Remove front grille.
3) Disconnect harness and couplers from headlight assembly.
4) Remove three bolts and pull headlight assembly off vehicle.
INSTALLATION
Reverse removal procedure for installation.
Make sure to follow HEADLIGHT AIMING WITH SCREEN and aim
headlight after installation.

YH4
GRAND
VITARA
1. Meter cluster
2. Hazard switch
Terminal
Wire ColorSwitch Position
LH steering vehicle shown
LIGHTING SYSTEM 8B-9
TURN SIGNAL AND HAZARD WARNING
LIGHTS
TURN SIGNAL SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
TLTBTR
G/RGG/Y
L
N
R
REMOVAL AND INSTALLATION
Refer to Section 3C COMBINATION SWITCH for vehicle without air
bag system and Section 3C1 CONTACT COIL AND COMBINA-
TION SWITCH ASSEMBLY for vehicle with air bag system.
HAZARD SWITCH
REMOVAL
1) Remove meter cluster.
2) Pull hazard switch out of instrument panel.
3) Disconnect coupler from hazard switch.
4) Remove hazard switch.
INSTALLATION
Reverse removal procedure.
INSPECTION
Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace siwtch.

YH4
GRAND
VITARA
8C-6 INSTRUMENTATION / DRIVER INFORMATION
KeyPosition
TerminalWire
color
Hard Top Model
Canvas Top Model
ON-VEHICLE SERVICE
IGNITION (MAIN) SWITCH
INSPECTION
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Disconnect main switch lead wire coupler.
4) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace ignition
(main) switch.
+B+ACCIG1-1IG1-2IG2STL1L2K1K2
W/YBlB/WB/WY/BB/YBBGG
OUTLOCKLOCK
ACC
IN
ON
START
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Remove steering column referring to Section 3C1 of this manu-
al. Then remove steering lock / ignition (main) switch from steer-
ing column.
INSTALLATION
1) Install steering lock / ignition (main) switch to steering column.
Install steering column assembly referring to Section 3C1 of this
manual.
2) Enable air bag system. Refer to ENABLING AIR BAG SYSTEM
in Section 10B of this manual.
NOTE:
When installing steering column, special care must be tak-
en for tightening sequence and its torque.

YH4
GRAND
VITARA
WASHER
ONINT
LO
HI
Type A
Type B
Type C
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-9
Wiper
SW
Terminal
Wiper SW
Terminal
ON-VEHICLE SERVICE
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER
INSPECTION
Front Wiper and Washer Switch (in Combination Switch)
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
B3+2+1AsB3+2+1As
OFFB3WINTB3W
LOOFF
HION
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
Wiper Motor
1) As illustrated, use a 12 V battery to connect its (+) terminal to ter-
minal ªAº, and its (±) terminal to Black lead wire (2) (Type A, B)
or terminal ªEº (Type C).
If motor (1) rotates at a low revolution speed of 45 to 55 rpm, it
is proper. For high speed check, connect battery (+) terminal to
terminal ªBº, and its (±) terminal to Black lead wire (2) (Type A,
B) or terminal ªEº (Type C). If motor rotates at a high revolution
speed of 67 to 83 rpm, it is proper.

YH4
GRAND
VITARA
1. (a)
1. (a)
1
11
Tightening Torque
(a): 23 N.m (2.3 kg-m, 17.0 lb-ft)
1. Bolt
BODY SERVICE 9-33
INSTRUMENTATION AND DRIVER INFORMATION
INSTRUMENT PANEL
WARNING:
See WARNING at the beginning of this section.
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to ªDisabling Air Bag Systemº in
Section 10B.
3) Remove console box.
4) Remove glove box and column hole cover.
5) Disconnect wires and cables from heater unit and blower motor
assembly.
6) Remove steering column assembly. Refer to Section 3C1.
7) Disconnect speedometer connector and remove speedometer
assembly. If equipped with air bag, disconnect wire coupler at
SDM and air bag ground terminal for air bag.
8) Remove engine hood opener.
9) Disconnect couplers which need to be disconnected for removal
for instrument panel.
10) Remove instrument panel mounting screws.
11) Remove instrument panel mounting bolt.
12) Remove instrument panel.
CAUTION:
For vehicle with Air Bag, instrument panel could not be re-
moved with SDM coupler connected and ground terminal
installed.
Use care not to damage Air Bag harness.
INSTALLATION
1) Install instrument panel by reversing removal procedure, noting
the following items.

When installing each part, be careful not to catch any cable or
wiring harness.

When installing steering column assembly, refer to ªAIR BAG
STEERING COLUMN INSTALLATIONº in Section 3C1.
2) Adjust control cables. (Refer to Section 1A ªHEATER CON-
TROL CABLESº.)
3) Enable air bag system. Refer to ªEnabling Air Bag Systemº in
Section 10B.

YH4
GRAND
VITARA
BODY SERVICE 9-63
KEY CODING
KEY USAGE AND IDENTIFICATION
Key is used for ignition and door lock cylinder. Keys are cut on both
edges to make them reversible.
Key identification is obtained from five character key code stamped
on key code tag. Using this key code, key code cutting combination
can be determined from a code list (available to owners of key cut-
ting equipment from suppliers).
If key codes are not available from records or tags, key code can
be obtained from the right hand door lock cylinder (if lock has not
been replaced). Lock cylinders supplied by the factory as service
parts are unmarked.
If original key is available, key code cutting combination can be de-
termined by laying key.
IGNITION SWITCH LOCK CYLINDER
Removal / Installation
See Section 3C1, ªAIR BAG STEERING WHEEL AND COLUMNº.
ELECTRICAL DIAGNOSIS
For ignition switch electrical troubleshooting, see Section 8, ªBODY
ELECTRICAL SYSTEMº.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-33
BASE OF COLUMN1. Paper
STEERING
WHEEL
CODE 21 ± DRIVER AIR BAG INITIATOR CIRCUIT RESISTANCE HIGH (Page 2 of 2)
STEPACTIONYESNO
31) With ignition switch OFF, disconnect Special
Tool (B) then reconnect contact coil connector
located near the base of the steering column.
2) Remove driver air bag (inflator) module from
steering wheel (Refer to SECTION 3C1).
3) Check proper connection to driver air bag
(inflator) module at terminals in ªDº connector.
4) If OK then connect Special Tool (B) to driver
air bag (inflator) module disconnected at step 2).
5) With ignition switch ON, is DTC 21 current?1) Ignition switch OFF.
2) Replace contact coil
assembly (Refer to
SECTION 3C1).1) Ignition switch OFF.
2) Replace driver air
bag (inflator)
module (Refer to
SECTION 3C1).
Fig. for STEP 1 and 2 Fig. for STEP 2
Fig. for STEP 3
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.