ABS SUZUKI GRAND VITARA 2002 2.G Service Owner's Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2002, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2002 2.GPages: 801, PDF Size: 12.15 MB
Page 230 of 801
YH4
GRAND
VITARA
ªAº: Drill hole with approximately
3 mm (0.12 in.) diameter.
REAR SUSPENSION 3E-3
DIAGNOSIS
DIAGNOSIS TABLE
Refer to SECTION 3.
SHOCK ABSORBER CHECK
Inspect for deformation or damage.
Inspect bushings for wear or damage.
Inspect for evidence of oil leakage.
Replace any defective part.
WARNING:
When handling rear shock absorber in which high-pressure
gas is sealed, make sure to observe the following precau-
tions.
1) Don't disassemble it.
2) Don't put it into the fire.
3) Don't store it where it gets hot.
4) Before disposing it, be sure to drill a hole in it where
shown by an arrow in the figure and let gas and oil out.
Lay it down sideways for this work.
5) The gas itself is harmless but it may issue out of the hole
together with chips generated by the drill. Therefore, be
sure to wear goggle.
LOWER ROD, UPPER ROD, LATERAL ROD
CHECK
Inspect for cracks, deformation or damage.
Replace any defective part.
Inspect each bush for wear and breakage. If found defective, re-
place.
AXLE HOUSING AND COIL SPRING CHECK
Inspect for cracks, deformation or damage.
Inspect for evidence of oil leakage at axle housing.
If any, replace defective part.
Page 232 of 801
YH4
GRAND
VITARA
1. Rear axle housing
2. Floor jack
1. Lock nut (if equipped)
2. Absorber nut
3. Upper support
4. Rubber bush
5. Lower support
6. Shock absorber
7. Bolt
Upper side
Lower side
1. Lock nut (if equipped)
2. Absorber nut
3. Body outside
REAR SUSPENSION 3E-5
ON-VEHICLE SERVICE
SHOCK ABSORBER
The shock absorber is non-adjustable, non-refillable, and cannot
be disassembled. The only service the shock absorber requires is
replacement when it has lost its resistance, is damaged, or leaking
fluid.
REMOVAL
1) Hoist vehicle and remove rear wheel.
2) Support rear axle housing by using floor jack to prevent it from
lowering.
3) Remove lock nut (if equipped) and absorber nut.
4) Remove lower mounting bolt.
5) Remove shock absorber.
INSTALLATION
1) Install shock absorber. Refer to figure for proper installing direc-
tion of lower mounting bolt.
2) Remove floor jack.
3) Lower hoist.
4) Tighten nuts to specified torque.
NOTE:
Tighten lower nut with vehicle off hoist and in non-loaded
condition.
Tightening Torque
(a): 29 N
.m (2.9 kg-m, 21.0 lb-ft)
(b): 85 N
.m (8.5 kg-m. 61.5 lb-ft)
Page 233 of 801
YH4
GRAND
VITARA
1. Parking brake
cable hanger
2. Cross member
3. Clamp
4. Chassis frame1. Rear axle housing
2. Floor jack
1. Shock absorber
2. Lower bolt
1. Clamp
2. Upper rod
3E-6 REAR SUSPENSION
COIL SPRING
REMOVAL
1) Hoist vehicle and remove rear wheel.
2) Support rear axle housing by using floor jack.
3) Disconnect parking brake cable hanger from chassis frame and
clamp from cross member.
4) Remove shock absorber lower mounting bolt.
5) Remove wheel speed sensor clamps from upper rod and axle
housing, if equipped with ABS.
For right side, remove E-ring for fixing brake pipe from cross
member and disconnect breather hose from axle housing.
6) Lower rear axle housing gradually as far down as where coil
spring can be removed.
7) Remove coil spring.
Page 234 of 801
YH4
GRAND
VITARA
1. Rear axle housing
2. Spring seat
3. Coil spring
4. Stepped part
1. Body center
2. Body outside
1. Body center
2. Body outside 1. Parking brake
cable hanger
2. Cross member
3. Clamp
4. Chassis frame
REAR SUSPENSION 3E-7
INSTALLATION
1) Install coil spring on spring seat of axle housing and then raise
axle housing.
NOTE:
When seating coil spring, mate spring end with stepped
part of rear axle spring seat as shown.
2) Install shock absorber lower bolt. For its proper installing direc-
tion, refer to figure.
Nut should not be tightened.
3) Install wheel speed sensor clamp (if equipped) and E-ring, and
connect breather hose to axle housing.
4) Connect cable hanger to chassis frame and clamp to cross
member. Remove floor jack from axle housing.
5) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
6) Lower hoist and tighten absorber lower nut to specified torque.
Tightening Torque
(b): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
NOTE:
For tightening of lower nut, refer to NOTE given under
SHOCK ABSORBER INSTALLATION in this section.
Page 236 of 801
YH4
GRAND
VITARA
1. Clamp
2. Upper rod
1. Upper rod front bolt
2. Nut
3. Upper rod
4. Wheel speed sensor
harness bracket
(Toward outside of body)1. Upper rod
2. Bolt
5. Upper rod rear bolt
6. Washer
7. Body center
8. Front side
REAR SUSPENSION 3E-9
UPPER ROD
REMOVAL
1) Hoist vehicle and remove rear wheel.
2) If equipped with ABS, disconnect wheel speed sensor harness
clamp from left upper rod.
3) Remove upper rod.
INSTALLATION
1) Install upper rod to chassis frame and axle housing, referring to
figure for installing direction of bolts.
Nuts should not be tightened.
2) See figure for distinction of installing direction of left side upper
rod for vehicle equipped with ABS.
3) Connect wheel speed sensor harness clamp to upper rod (if
equipped with ABS).
4) Lower hoist and with vehicle in non-loaded condition, tighten
front bolt and rear nut of upper rod to specified torque.
Tightening Torque
(a): 90 N
.m (9.0 kg-m, 65 lb-ft)
Page 238 of 801
YH4
GRAND
VITARA
1. Bearing retainer
2. Parking brake shoe
lever
3. Clearance1. Wheel speed sensor
1
L
REAR SUSPENSION 3E-11
4) Remove wheel speed sensor from rear axle housing (if
equipped with ABS).
CAUTION:
Do not pull wire harness or twist more than necessary
when removing rear wheel speed sensor.
Do not cause damage to surface of rear wheel speed
sensor or pole piece and do not allow dust, etc. to enter
its installation hole.
5) Check to ensure that there is clearance between rear wheel
bearing retainer and parking brake shoe lever. If no clearance
is found, loosen cable locking nut further to obtain clearance.
6) Using special tools (B) & (C) indicated below, draw out axle
shaft.
NOTE:
Use care not to pull brake back plate along with shaft.
CAUTION:
Pull out axle shaft using care so that upper and lower
brake struts and parking cable are not caught.
Special Tool
(C): 09943-35512
(B): 09942-15510
7) Rear axle shaft that was drawn out.
Shaft length ªLº:
Left side: 711.5 mm (28.0 in.)
Right side: 757.5 mm (29.8 in.)
8) If equipped with ABS, in order to remove sensor rotor from re-
tainer ring, grind with a grinder one part of the sensor rotor as
illustrated till it becomes thin.
Page 239 of 801
YH4
GRAND
VITARA
1. Axle shaft
2. Wheel bearing
3. Press
1. Stud bolt
2. Hydraulic press
1. Rear wheel bearing
retainer ring
2. Grind with a grinder
3. Rear axle
3E-12 REAR SUSPENSION
9) Break with a chisel the thin ground sensor rotor, and it can be
removed (if equipped with ABS).
10) In order to remove the retainer ring from the shaft, grind with
a grinder two parts of the bearing retainer ring as illustrated till
it becomes thin.
CAUTION:
Be careful not to grind too far not to damage the shaft.
11) Break with a chisel the thin ground retainer ring, and it can be
removed.
12) Remove bearing from shaft by using hydraulic press.
13) Remove bearing retainer.
14) Remove stud bolt(s) by using hydraulic press.
Page 240 of 801
YH4
GRAND
VITARA
[B]
1
2
[A]
1. Bearing retainer
2. Oil seal
3. Wheel side
4. Differential side
1. Stud bolt
2. Nut
3. Washer
4. Flange of axle shaft
1. Axle shaft
2. Bearing retainer
[A]: Vehicle without ABS
[B]: Vehicle with ABS
1. Bearing
2. Retainer ring
REAR SUSPENSION 3E-13
INSTALLATION
Install removed parts in reverse order of removal procedure, noting
the following.
1) Apply grease to oil seal lip as shown and install it to axle shaft.
NOTE:
Amount of grease applied to hollow in oil seal should be
more than 60% of its vacant space.
ªAº: Grease 99000-25010
2) Aligning serrations between new stud bolt(s) and flange, install
new stud bolt(s) by tightening nut as shown.
3) Install bearing retainer to shaft.
4) Press-fit wheel bearing and retainer ring as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
Refer to figure so that wheel bearing is installed in proper
direction.
Page 241 of 801
YH4
GRAND
VITARA
1. Sensor rotor
1. Axle housing
1. Bearing retainer
(b)
3E-14 REAR SUSPENSION
5) For vehicle with ABS, press-fit new sensor rotor as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
6) Apply grease to axle shaft inner oil seal lip as shown.
ªAº: Grease 99000-25010
7) Apply sealant to mating surface of bearing retainer with brake
back plate.
NOTE:
Make sure to remove old sealant before applying it anew.
ªBº: Sealant 99000-31110
8) Install rear axle shaft to rear axle housing and tighten bearing
retainer nuts to specified torque.
NOTE:
When installing rear axle shaft, be careful not to cause
damage to oil seal lip in axle housing.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
9) Tighten wheel speed sensor bolt to specified torque (if
equipped with ABS).
Tightening Torque
(b): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
10) Refill rear axle (differential) housing with new specified gear oil.
Refer to SECTION 7F for refill.
11) Install brake drum. (For details, refer to BRAKE DRUM
INSTALLATION in SECTION 5.)
Page 243 of 801
YH4
GRAND
VITARA
1. Brake pipe flare nut
2. Brake pipe
3. Brake back plate
1. Bearing retainer
2. Parking brake shoe
lever
3. Clearance1. Nut 1. Wheel speed sensor
2. Wheel speed sensor coupler
3. Wheel speed sensor harness clamp
4. Wheel speed sensor harness
3E-16 REAR SUSPENSION
REAR AXLE HOUSING
REMOVAL
1) Drain differential gear oil.
Carry out steps 2) to 7) and 15) to 18) on both right and left
wheels.
Note that left wheel and its related parts are used in illustrations
in this section.
2) Remove rear brake drum. (Refer to steps 1) to 5) of BRAKE
DRUM REMOVAL.)
3) Disconnect brake pipe from wheel cylinder. With right side wheel
cylinder, disconnect 2 brake pipes.
4) For vehicle with ABS, disconnect wheel speed sensor coupler
and remove wheel speed sensor with its harness.
5) Remove rear wheel bearing retainer nuts from rear axle hous-
ing.
6) Check to ensure that there is clearance between rear wheel
bearing retainer and parking brake shoe lever. If no clearance
is found, loosen cable locking nut further to obtain clearance.