Bearing SUZUKI GRAND VITARA 2002 2.G Service Owner's Manual

YH4
GRAND
VITARA
3D-4 FRONT SUSPENSION
SUSPENSION CONTROL ARM JOINT CHECK
1) Check for smoothness of rotation.
2) Inspect ball stud for damage.
3) Inspect dust cover for damage.
Replace any parts found defective in steps 1) ± 3).
SUSPENSION CONTROL ARM BUSHING
CHECK
Inspect for damage, wear or deterioration.
WHEEL DISC, NUT & BEARING CHECK
1) Inspect each wheel disc for dents, distortion and cracks.
Disc in badly damaged condition must be replaced.
2) Check wheel nuts for tightness and retighten them to specifica-
tion as necessary.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
3) Check wheel bearing for wear. After retightening lock nut to spe-
cified torque, apply dial gauge to wheel hub center and measure
thrust play.
Thrust play limit: 0.05 mm (0.002 in.)
When measurement exceeds limit, replace bearing.
4) By rotating wheel actually, check wheel bearing for noise and
smooth rotation. If defective, replace bearing.

YH4
GRAND
VITARA
3D-12 FRONT SUSPENSION
1. Lock washer
2. Screws 1. Axle shaft drive flange
WHEEL HUB (INCLUDED WHEEL BEARING)
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove axle shaft drive flange (4WD vehicle) or hub cap (2WD
vehicle).
3) If equipped with ABS, remove wheel speed sensor from knuckle
and harness clamp from strut.
4) Remove caliper bolt and suspend caliper.
CAUTION:
Hang removed caliper with a wire hook or the like so as to
prevent brake hose from bending and twisting excessively
or being pulled.
Don't operate brake pedal with pads removed.
5) Remove brake disc.
NOTE:
If brake disc can not be removed by hand, use 8 mm bolts as
shown.
6) Remove front wheel bearing lock washer by loosening 4 screws.
7) Remove front wheel bearing lock nut by using special tool.
Special Tool
(A): 09951-16050
8) Remove front wheel bearing washer.
9) Remove wheel hub component by hand.

YH4
GRAND
VITARA
1. Sensor rotor
2. Wheel hub
3. Vise
4. Flat end rod
1. Bearing lock washer
2. Screw
3. Bearing lock nut
4. Wheel bearing washer
5. Wheel hub component
6. Bolt
1. Oil hydraulic press
2. Hub bolt
FRONT SUSPENSION 3D-13
NOTE:
If wheel hub can not be removed by hand, use special tools
as shown.
Special Tool
(B): 09943-35512
(C): 09942-15510
CAUTION:
If wheel bearing inner race remains on wheel spindle
when removing wheel hub, which means break of wheel
bearing, replace wheel hub component (included wheel
bearing).
10) Remove sensor rotor from wheel hub as shown (if equipped
with ABS).
CAUTION:

Pull out sensor rotor from wheel hub gradually and
evenly.

Do not reuse sensor rotor once removed.
Be sure to new sensor rotor when installing.
11) Remove hub bolts from hub.
INSTALLATION
1) Insert new stud in hub hole. Rotate stud slowly to assure serra-
tions are aligned with those made by original bolt.

YH4
GRAND
VITARA
1. Wheel hub
2. Wheel spindle
3. Bearing inner race
1. Lock washer 1. Sensor rotor
2. Wheel hub
3. Hydraulic press
OK NG
3D-14 FRONT SUSPENSION
2) Install new sensor rotor by using special tool (if equipped with
ABS).
NOTE:
Use care not to insert wheel hub diagonally.
Special Tool
(A): 09952-86510
(B): 09924-74510
Wheel speed sensor rotor installing position
Reference Dimension ªaº : 4.9
0.1 mm (0.19
0.004 in.)
3) Install wheel hub component to spindle supporting wheel bear-
ing inner race by finger as shown.
CAUTION:
Don't tap wheel hub component by hammer or the like.
Otherwise, it will be broken.
NOTE:
When it is impossible to install wheel hub component by
hand, which means the inner race is out of alignment, re-
move wheel hub component once and reinstall it.
4) Install wheel bearing washer, and the install wheel bearing lock
nut.
5) Tighten wheel bearing lock nut to specified torque while turning
wheel hub by hand.
Special Tool
(A): 09951-16050
Tightening Torque
(a): 216 N
.m (21.6 kg-m, 157 lb-ft)
6) Using lock washer, lock bearing lock nut. If lock screw hole is not
aligned with screw hole in lock nut, turn lock nut in tightening
direction till they align.
Tightening Torque
(b): 1.5 N
.m (0.15 kg-m, 1.1 lb-ft)

YH4
GRAND
VITARA
1. Drive shaft
circlip
2. Spindle thrust
washer
3. Drive shaft
4. Wheel spindle
1. Tie-rod end
2. Knuckle
1. Strut
2. Knuckle
1. Dust cover
2. Wheel spindle
3. Knuckle
4. Inner oil seal /
knuckle cap
FRONT SUSPENSION 3D-17
KNUCKLE / WHEEL SPINDLE
REMOVAL
1) Remove wheel hub. Refer to ªWHEEL HUB (INCLUDED
WHEEL BEARING)º in this section.
2) Remove front drive shaft circlip and front spindle thrust washer
(for 4WD vehicle) or front hub cap (for 2WD vehicle).
3) Disconnect tie-rod end from knuckle.
4) Remove stabilizer bar. Refer to ªSTABILIZER BAR / BUSH-
INGSº in this section.
5) Remove ball stud nut.
6) Support lower arm with jack.
7) Remove strut bracket bolts from strut bracket.
8) By using puller, disconnect knuckle from ball stud.
9) While lowering jack, remove knuckle / wheel spindle comp.
10) Remove inner oil seal (for 4WD vehicle), knuckle cap (for 2WD
vehicle), dust cover and wheel spindle.

YH4
GRAND
VITARA
ªAº
ªBº
1. Wheel spindle
2. Drive shaft bearing
1. Wheel spindle
2. Drive shaft
bearing
3. Front drive shaft
thrust washer
4. Inner oil seal
5. Knuckle cap
6. Drive shaft oil sealType A Type B
1. Drive shaft bearing
2. Wheel spindle
3D-18 FRONT SUSPENSION
11) For 4WD vehicle
Remove drive shaft bearing by using special tool.
Special Tool
(A): 09923-74510
(B): 09930-30102
INSTALLATION
Reverse removal sequence to install knuckle, wheel spindle oil seal
and drive shaft bearing,noting following points.

For 4WD vehicle
Install drive shaft bearing by using special tool.
Special Tool
(A): 09913-76010 Type A drive shaft thrust washer. . . . . . . .
(A): 09913-80112 Type B drive shaft thrust washer. . . . . . . .
Dimension ªaº: 0 ± 1 mm (0 ± 0.04 in.)
Dimension ªaº: Type A drive shaft thrust washer . . . . . . . . .
Dimension ªaº: 1.75 ± 2.50 mm (0.069 ± 0.098 in.)
Dimension ªaº: Type B drive shaft thrust washer . . . . . . . . .

When installing wheel spindle to knuckle, coat their mating sur-
faces with sealant.
ªAº: Sealant 99000-31110

For 4WD vehicle
Also, fill recess in wheel spindle with about 10 g lithium grease.
ªBº: Grease 99000-25010

YH4
GRAND
VITARA
(a)
1. Axle shaft drive flange
2. Bolt1. Hub cap
2. Wheel hub
3D-20 FRONT SUSPENSION

Tighten control arm ball stud nut
When tightening ball stud nut, use new nut and tighten it to speci-
fied torque.
Tightening Torque
(a): 60 N
.m (6.0 kg-m, 43.5 lb-ft)

For 2WD vehicle
Apply water tight sealant to mating surface of wheel hub and
install hub cap to wheel hub.
ªAº: Sealant 99000-31090

For 4WD vehicle
When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange.
ªAº: Sealant 99000-31090
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

For installation procedures of wheel hub component, refer to
ªWHEEL HUB (INCLUDED WHEEL BEARING)º in this section.

Connect tie-rod end to knuckle and tighten new tie-rod end nut.
Tightening Torque
(a): 43 N
.m (4.3 kg-m, 31.5 lb-ft)

For any tightening torque other than those specified in text, refer
to ªTIGHTENING TORQUE SPECIFICATIONº in this section.

YH4
GRAND
VITARA
3D-24 FRONT SUSPENSION
REQUIRED SERVICE MATERIALS
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSENO.
Lithium greaseSUZUKI SUPER GREASE (A)
(99000-25010)
Bearing inner oil seal / drive shaft oil seal
Recess of wheel spindles
Spindle outer washer
Spindle part of drive shaft
Spindle bush (inside and flange part)
Spindle inner washera
b
c
d
e
f
SealantSUZUKI BOND NO. 1215
(99000-31110)Mating surfaces of wheel spindle
and knuckle1
Sealing compound
SUZUKI SEALING COM-
POUND 366E
(99000-31090)
Front axle cap
Mating surfaces of wheel hub and drive
flange
Knuckle cap
Hub capA
B
C
D

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-25
09923-74510
Bearing remover09930-30102
Sliding shaft09924-74510
Bearing installer handle09941-66010
Bump stopper wrench
09942-15510
Sliding hammer09943-35512
Brake drum remover09944-68210
Bearing & oil seal installer 09944-66010
Wheel hub / knuckle oil
seal installer
09951-16050
Wheel bearing tightening tool09951-46020
Control arm remover support 09951-16060
Control arm bush remover
(front)09913-80112
Bearing installer
09925-58210
Oil seal installer09913-85210
Oil seal installer
09952-86510
Front sensor rotor installer
SPECIAL TOOLS

YH4
GRAND
VITARA
3E
REAR SUSPENSION 3E-1
GENERAL DESCRIPTION3E- 2 . . . . . . . . . . . . . .
DIAGNOSIS3E- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3E- 3. . . . . . . . . . . . . . . . . . . . . .
Shock Absorber Check 3E- 3. . . . . . . . . . . . . . . .
Lower / Upper / Lateral Rod Check 3E- 3. . . . . . . .
Axle Housing and Coil Spring Check 3E- 3. . . .
Bearing Retainer & Axle Shaft Inner Oil
Seal Check 3E- 4. . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Disc, Nut & Bearing Check 3E- 4. . . . . .
ON-VEHICLE SERVICE3E- 5 . . . . . . . . . . . . . . . .
Shock Absorber 3E- 5. . . . . . . . . . . . . . . . . . . . . . Coil Spring 3E- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Lower Rod 3E- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Rod 3E- 9. . . . . . . . . . . . . . . . . . . . . . . . . .
Lateral Rod 3E-10. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Axle Shaft and Wheel Bearing 3E-10. . . . .
Rear Axle Shaft Inner Oil Seal 3E-15. . . . . . . . . .
Rear Axle Housing 3E-16. . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3E-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3E-23 . . . . . .
SPECIAL TOOLS3E-24 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3E
REAR SUSPENSION
NOTE:

All suspension fasteners are an important attaching part in that it could affect the performance of vital
parts and systems, and / or could result in major repair expense. They must be replaced with one of the
same part number or with an equivalent part if replacement becomes necessary. Do not use a replace-
ment part of lesser quality or substitute design. Torque values must be used as specified during reas-
sembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any suspension part. Replace it with a new part, or damage
to the part may result.
CONTENTS